Hager EE804A Bedienungsanleitung

Hager Bewegungsmelder EE804A

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hager EE804A (2 Seiten) in der Kategorie Bewegungsmelder. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
1 09/2017 - 6LE002943AHager Controls S.A.S., 33 rue Saint-Nicolas, B.P. 10140, 67703 SAVERNE CEDEX, France - www.hager.com
6LE002943A
EE804A
Presence and motion detector
360°, surface-mounted
EE805A
Presence and motion detector
360°, flush-mounted
z
Design and layout of the device
(Figure 1/2)
(1) Connecting terminals
(2) Mounting device locking screw
(3) Release opening
(4) Fastening grids
(5) Detector lens
(6) Response brightness potentiometer
(7) Potentiometer delay time
(8) Cover for potentiometer
(9) Locking screw
(10) Fixing springs
(11) Strain relief with mounting device for cable
ties
(12) Cover for connection compartment
Function
Correct use
- automatic switching of electric loads depend-
ing on heat motion and ambient brightness
- EE804A: Surface-mounted installation or in-
stallation on mounting box according to DIN
49073
- EE805A: Cavity installation
Product characteristics
- Combination of presence and motion detector
with enhanced detection sensitivity in the cen-
tral presence-detection area
- Response brightness adjustable
- Delay time adjustable
Behaviour during operation
The motion detector detects heat motion caused
by people, animals, or objects.
- will be switched on for the delay time if move-
ments are detected in the detection area and
the set response brightness is undershot.
Each detected movement restarts the delay
time.
- will be switched off if no additional movements
are detected in the detection area and the set
delay time has elapsed or the set response
brightness is exceeded.
Information for electricians
Installation and electrical connection
DANGER!
Touching live parts can result in an
electric shock!
An electric shock can be lethal!
Disconnect the connecting cables
before working on the device and
cover all live parts in the area!
ç
Selecting installation location
The motion detector must be installed horizontally
on the ceiling. It has an detection angle of 360°.
The diameter of the detection area depends on the
installation height. At an installation height of 2.5
m, the diameter at ground level is approx. 6 m. The
diameter of the inner detection area with enhanced
detection sensitivity is 4 m (îš¿gure 3).
At an installation height greater than 2.5 m, the
detection area increases. At the same time, the
detection sensitivity decreases.
Observe the motion orientation: a distinction is
made between "direct approach" and "trans-
verse motion". Motions transverse to the motion
detector can be detected better than motions
toward the motion detector (Fig. 4).
îš„If used as a presence detector, the device must
be installed so that areas with less motion activ-
ity (desk, seating area) are within the detection
area (îš¿gure 3).
îš„Avoid sources of interference in the detection
area. Sources of interference, e.g. heating
elements, ventilation systems, air conditioners
and lamps that are cooling down can cause
undesired switching (Fig. 5).
îš„Select an installation location that is free of
vibration. Vibrations can cause undesired
switching.
Connecting and installing the surface-mounted
variant EE804A (îš¿gure 7)
îš„Run the connection cable through the insertion
opening (13).
îš„Install device socket under the cover using the
screw dowel set enclosed. Installation can be
done on a ush-mounted box if available
îš„Connect device according to connection dia-
gram (îš¿gure 6).
îš„Snap onto base
îš„Screw in locking screw (9).
îš„Conîš¿gure settings.
îš„Close cover (8).
z
Safety instructions
Electrical equipment may only be installed and
assembled by a qualiîš¿ed electrician in accord-
ance with the relevant installation standards,
regulations, directives and safety and accident
prevention directives of the country.
Failure to comply with these installation in-
structions may result in damage to the device,
îš¿re or other hazards.
Due to its detection behaviour the device is not
suitable for use in burglary detection or alarm
systems.
These instructions are an integral component of
the product and must be retained by the end user.
(1)
(8)
(9)
(2)
(3)
(5)
(4)
(6) (7)
1
4
(4)
(5)
(10)
(11)
(12)
(10)
2
(6) (7)
0 m 2 m2 m
1 m
2 m
2,5 m
3 m3 m
3
2 09/2017 - 6LE002943AHager Controls S.A.S., 33 rue Saint-Nicolas, B.P. 10140, 67703 SAVERNE CEDEX, France - www.hager.com
Connecting and installing the ush-mounted
variant EE805A (îš¿gure 8)
Establish installation opening Ø 75 mm.
îš„Connect motion detector according to the
connecting diagram (îš¿gure 6).
îš„Establish strain relief on the corresponding
mounting devices (11) with cable ties.
îš„Attach cover (12).
îš„Conîš¿gure settings.
îš„Insert the two îš¿xing springs (10) through the
installation opening while pressing upwards
and allow them to spring back.
Commissioning
Testing the detection
In test mode, the motion detector works with max-
imum response brightness. If motion is detected,
the load is switched for approx. 2 seconds. After
approx. 20 cycles, the operating cycles decrease
in order to protect the connected load.
îš„Set potentiometer response brightness (6) to
(right end stop) (îš¿gure 1/2).
îš„Set potentiometer delay time (7) to minimal
(left end stop) (îš¿gure 1/2).
The device is in test mode.
îš„Carry out test by moving in the detection area.
If the motion detector switches on without
motion in the detection area, then sources
of interference are present (see Installation
location).
Setting the response brightness
The response brightness is the brightness value
saved in the motion detector; when this value is
undershot the connected load is switched on if
movements are detected. The brightness thresh-
old can be set continuously between approx.
5 ( ) and 1000 Lux ( , daytime operation/bright-
ness-independent).
To control the lighting in stairwells in accord-
ance with EN12464-1, select the potentiometer
setting > 150 Lux (e.g factory setting, 200 Lux).
îš„Turn the response brightness potentiometer (6)
to the desired position.
Set delay time
The delay time is the period of time set in the
motion detector which is the shortest time that
the lighting is switched on when the response
brightness is undershot and motion is detected.
On delivery, the delay time is set to approx. 3
minutes.
îš„Turn the delay time potentiometer (7) to the
desired position.
Appendix
Technical data
Supply voltage 230V~, +10%/-15%
240V~, +6/-6%
Frequency 50/60Hz
Power consumption without load 0.3 W
Delay time, adjustable
- Operation 5s - 30 min
- Test mode 2 s
- Factory setting ~ 3 min
Response brightness, adjustable 5 ... 1000 Lux
- Factory setting 200 Lux
Recommended installation height 2.5 m ... 3.5 m
maximum installation height 4 m
Detection area Ø motion
(installation height 2.5 m) ~ 6 m
Detection area Ø presence
(installation height 2.5 m.) ~ 4 m
Detection angle 360°
Closing contact with
zero cross switching 10 A AC1, 230 V~
Upstream circuit breaker 10A
Incandescent and halogen lamps 230 V 2300 W
LED lamps/
Compact uorescent lamps 20 x 20 W (400 W)
Ferromagnetic transformers 1500 VA
Electronic transformers 1500 W
Fluorescent lamps
- parallel compensated 1000 W
- with electronic ballast 1000 W
Relative humidity (no condensation) 30°C, 95%
Operating temperature -5 °C ... +45°C
Storage/transport temperature -25 °C... +70 °C
Degree of protection IP 21
Protection class II
Impact resistance IK 04
Dimensions EE804A (Ø x H) 100 x 50 mm
Dimensions EE805A (Ø x H) 90 x 61 mm
Connection cross-section
- EE804A, screw terminals 1 mm² ... 2.5 mm²
- EE805A, plug-in terminals 1 mm² ... 2.5 mm²
Correct Disposal of this product (Waste
Electrical & Electronic Equipment).)
(Applicable in the European Union and
other European countries with separate
collection systems).
This marking shown on the product or its literature
indicates that it should not be disposed with other
household waste at the end of its working life.
To prevent possible harm to the environment or
human health from uncontrolled waste disposal,
please separate this device from other types of
wastes. Recycle the device responsibly to pro-
mote the sustainable reuse of material resources.
Household users should contact either the retailer
where they purchased this product, or their local
government ofîš¿ce, for details of where and how
they can take this device for environmentally safe
recycling.
Business users should contact their supplier and
check the terms and conditions of the purchase
contract. This product should not be mixed with
other commercial wastes of disposal.
(13)
L
L
L‘N
N
PE
Ø 75 mm
5
6
78

Produktspezifikationen

Marke: Hager
Kategorie: Bewegungsmelder
Modell: EE804A

Brauchst du Hilfe?

Wenn Sie Hilfe mit Hager EE804A benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Bewegungsmelder Hager

Hager

Hager EE805A Bedienungsanleitung

3 September 2024
Hager

Hager EE840 Bedienungsanleitung

16 August 2024
Hager

Hager WUC11 Bedienungsanleitung

12 August 2024
Hager

Hager WUC31 Bedienungsanleitung

11 August 2024
Hager

Hager EE870 Bedienungsanleitung

10 August 2024
Hager

Hager EE860 Bedienungsanleitung

10 August 2024
Hager

Hager WUC20 Bedienungsanleitung

10 August 2024
Hager

Hager WUC10 Bedienungsanleitung

9 August 2024
Hager

Hager EE841 Bedienungsanleitung

7 August 2024
Hager

Hager EE880 Bedienungsanleitung

7 August 2024

Bedienungsanleitung Bewegungsmelder

Neueste Bedienungsanleitung für -Kategorien-

Orbis

Orbis Circumat Bedienungsanleitung

10 Oktober 2024
Vemer

Vemer Sensor 360L Bedienungsanleitung

6 Oktober 2024
Perel

Perel EMS103 Bedienungsanleitung

3 Oktober 2024
Renkforce

Renkforce 1362921 Bedienungsanleitung

27 September 2024
Busch-Jaeger

Busch-Jaeger Sicherheitstechnik 6800-0-2521 Bedienungsanleitung

17 September 2024
Busch-Jaeger

Busch-Jaeger 2CKA006200A0056 Bedienungsanleitung

15 September 2024
DSC

DSC PG9862 Bedienungsanleitung

14 September 2024
Maxsa

Maxsa 40234 Bedienungsanleitung

11 September 2024
Maxsa

Maxsa 43218 Bedienungsanleitung

11 September 2024
ORNO

ORNO OR-CR-233 Bedienungsanleitung

10 September 2024