WyreStorm EX-40-G3 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für WyreStorm EX-40-G3 (4 Seiten) in der Kategorie AV extender. Dieser Bedienungsanleitung war für 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
1080p HDMI-over-UTP Extender with IR and PoC
EX-40-G3 Quickstart Guide
Copyright © 2019 WyreStorm Technologies | wyrestorm.com
EX-40-G3 Quickstart Guide | 190121
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the
installation process.
Basic Wiring Diagram
IMPORTANT! Installation Requirements
• Visit the product page to download the latest rmware, document version,
additional documentation, and conguration tools.
• Read through the section for important wiring Wiring and Connections
guidelines before creating or choosing premade cables.
• While this product supports CEC, WyreStorm cannot guarantee
compatibility with all forms of CEC communication.
In the Box
1x EX-40-G3 Transmitter
1x EX-40-G3 Receiver
1x 5V DC 1A Power Supply (US/UK/EU/AU)
1x USB-A to Micro-B RX Power Cable
1x IR Emitter
1x IR Receiver
4x Mounting Brackets (2x for TX | 2x for RX)
1x Quickstart Guide (this document)
IR to Control System
CAB-IR-LINK (Sold Separately)
5V DC
Power Supply
5V DC
Power Supply
HDMI Display
EX-40-G3
Transmitter
EX-40-G3
Receiver
HDBaseT Cat5e/6/6a
HDMI Source
HDMI HDMI
KEY
HDMI
HDBaseT
IR
Power
Transmitter (TX)
Front Panel
Rear Panel
Front Panel
Rear Panel
Receiver (RX)
Power Input 5.5mm Screw Down Barrel Jack
Connect to the included power supply.
HDMI In 19-pin type A HDMI female
Supports HDMI and DVI/D with adapter
UTP Out 8-pin RJ-45 female
Connect the UTP In on the receiver (RX)
UTP In 8-pin RJ-45 female
Connect the UTP Out on the receiver (RX)
USB 5V
BackUp Power
USB Mirco. Connect to USB power when PoC
cannot be used
HDMI Out 19-pin type A HDMI female
Supports HDMI and DVI/D with adapter
CLong Cable Mode
Extends the distance of the AV transmission
past the normal operating distance of
30m/98ft. Refer to section Long Cable Mode
for more details
Copyright © 2019 WyreStorm Technologies | wyrestorm.com
EX-40-G3 Quickstart Guide | 190121
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
2 of 4
BA
BA
BA
B CA
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
• Verify that power is being supplied to the transmitter and receiving device.
• Verify that all HDMI and UTP connections are not loose and are functioning
properly.
• Verify that the HDBaseT cable is properly terminated following EIA568B
standard.
• Verify that the output resolution of the source and display is supported by
this extender.
• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
No or Intermittent 3rd party Device Control
• Verify that the IR and RS-232 cables are properly terminated following the
Wiring and Connections section.
Troubleshooting Tips:
• WyreStorm recommends using a cable tester or connecting the cable to
other devices to verify functionality.
Copyright © 2019 WyreStorm Technologies | wyrestorm.com
EX-40-G3 Quickstart Guide | 190121
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
3 of 4
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s
entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
IMPORTANT! Wiring Guidelines
• The use of patch panels, wall plates, cable extenders, kinks in cables, and
electrical or environmental interference will have an adverse effect on
signal transmission which may limit performance. Steps should be taken
to minimize or remove these factors completely during installation for best
results.
• WyreStorm recommends using pre-terminated HDMI cables due to the
complexity of these connector types. Using pre-terminated cables will
ensure that these connections are accurate and will not interfere with the
performance of the product.
IR TX/RX Guidelines
• Using WyreStorm infrared emitters and receivers is the best way to ensure
that most IR coding formats are transmitted and received by the NetworkHD
system. Other 3rd party emitters and receivers can be used; however, these
devices must operate in the same manner as the WyreStorm devices.
• Due to differences in IR across 3rd party control systems their IR ports
should never be connected directly to a NetworkHD system as an
incompatibility may exist. WyreStorm offers a cable that compensates for
voltage differences as well adjusts for differences in the pins used within the
port. Refer to the product page for more information.CAB-IR-LINK
IR TX Port Pinout
Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.
Tip: Anode
Sleeve: Cathode (IR Signal)
IR RX Port Pinout
Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs
+5V DC to power the included IR receiver.
Tip:
Ring: IR Signal
+5V DC
Sleeve: Ground (GND)
Long Cable Mode
This extender contains an option Long Cable Mode to extend the distance
of the AV transmission past the normal operating distance. Under normal
operation when using distances of 30m/98ft or less this feature should be
turned Off.
Set the switch to when the cable distance from Off
the TX to the RX is 30m/98ft or less.
Set the switch to to extend the cable distance On
from the TX to the RX up to 40m/131ft


Produktspezifikationen

Marke: WyreStorm
Kategorie: AV extender
Modell: EX-40-G3

Brauchst du Hilfe?

Wenn Sie Hilfe mit WyreStorm EX-40-G3 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung AV extender WyreStorm

Bedienungsanleitung AV extender

Neueste Bedienungsanleitung für -Kategorien-