Tripp Lite SmartPro SMART1050SLTAA Bedienungsanleitung

Tripp Lite Unterbrechungsfreies Stromversorgungssystem SmartPro SMART1050SLTAA

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Tripp Lite SmartPro SMART1050SLTAA (32 Seiten) in der Kategorie Unterbrechungsfreies Stromversorgungssystem. Dieser Bedienungsanleitung war für 36 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/32

Owner’s Manual

SmartPro® SLT

Intelligent, Line-Interactive UPS Systems

100/110/120V Input/Output • Sine Wave Output

Models:

Not suitable for mobile applications.

Important Safety Instructions 2

Quick Installation 3

Optional Installation 4

Basic Operation 4

Battery Replacement 9

Product Registration 10

Storage & Service 10

Español 12

Français 23

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com

® is a registered trademark of Tripp Lite.

SMART1050SLT,

SMART1050SLTAA

(Series No. AGSM5384)

SMART1500SLT

(Series No. AGSM7136)

PROTECT YOUR INVESTMENT!

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $100 value!

www.tripplite.com/warranty

16-02-272-932442.indb 1 2/18/2016 4:55:06 PM

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the

installation, operation and storage of all Tripp Lite UPS Systems. Failure to heed

these warnings may affect your warranty.

UPS Location Warnings

• Install your UPS indoors, away from excess moisture or heat, conductive

contaminants, dust or direct sunlight.

• For best performance, keep the indoor temperature between between 32º F and

104º F (0º C and 40º C).

• Leave adequate space around all sides of the UPS for proper ventilation.

UPS Connection Warnings

• Connect your UPS directly to a properly grounded AC power outlet. Do not plug the

UPS into itself; this will damage the UPS.

• Be sure to use the proper overcurrent protection for the installation, in accordance

with the plug/equipment rating.

• Do not modify the UPS's plug, and do not use an adapter that would eliminate the

UPS’s ground connection.

• Do not use extension cords to connect the UPS to an AC outlet.

• The electrical outlets supplying power to the equipment should be installed near the

equipment and easily accessible.

• If the UPS receives power from a motor-powered AC generator, the generator must

provide clean, filtered, computer-grade output.

Equipment Connection Warnings

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to

significantly affect its safety or effectiveness is not recommended. Do not use this

equipment in the presence of a flammable anesthetic mixture with air, oxygen or

nitrous oxide.

• Do not connect surge protectors or extension cords to the output of your UPS.

This might damage the UPS and will void the surge suppressor and UPS warranties.

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit

current. Observe proper precautions. There are no user-serviceable parts inside the

UPS. Do not open the UPS except to perform battery replacement. Do not open

batteries. Do not short or bridge the battery terminals with any object. Unplug and

turn off the UPS before performing battery replacement. Use tools with insulated

handles. Battery replacement should be performed only by authorized service personnel

using the same number and type of batteries (Sealed Lead-Acid). Do not dispose of

the batteries in a fire. The batteries are recyclable. Refer to your local codes for

disposal requirements or visit http://www.tripplite.com/support/recycling-program

for recycling information. Tripp Lite offers a complete line of UPS System

Replacement Battery Cartridges (R.B.C.).Visit Tripp Lite on the Web at

www.tripplite.com/support/battery/index.cfm to locate the specific replacement

battery for your UPS.

Important Safety Instructions

16-02-272-932442.indb 2 2/18/2016 4:55:07 PM

1 With the UPS disconnected from utility

power, use a small tool to set the

Voltage Dip Switch to match your input

voltage. (All models are preset to the

120V setting.)

2 Plug the UPS into an outlet on a

dedicated circuit.

NOTE! after you plug the UPS into a live AC

outlet, the UPS will automatically charge its

batteries,* but will not supply power to its

outlets until it is turned ON.

* The BATTERY CHARGE LED will be the only LED

illuminated

3 Plug your equipment into the UPS.

All outlets provide battery backup and surge

protection for computers, monitors and other

critical devices.

Do not plug high-draw equipment such as

laser printers into the battery backup/

surge protection outlets.

Note: Your UPS is designed to support electronic

equipment only. You will overload the UPS if the total VA

rating for all equipment connected through the battery

backup/surge protection outlets exceeds the UPS's

Output Capacity. To find your equipment's VA ratings, look

on their nameplates. If the equipment is listed in amps,

multiply the number of amps by 120 to determine VA.

(Example: 1 amp × 120 = 120 VA). If you are unsure if

you have overloaded the UPS's outlets, see “OUTPUT

LOAD LEVEL” LED description.

4 Turn the UPS ON.

Press and hold the “STANDBY” button for one

second. The alarm will beep once briefly after

one second has passed. Release the button.

Quick Installation

16-02-272-932442.indb 3 2/18/2016 4:55:10 PM

Produktspezifikationen

Marke:	Tripp Lite
Kategorie:	Unterbrechungsfreies Stromversorgungssystem
Modell:	SmartPro SMART1050SLTAA
Breite:	171 mm
Tiefe:	337 mm
Gewicht:	16300 g
Produktfarbe:	Schwarz
Akku-/Batterietyp:	RBC24-SLT
Akkuladezeit:	6 h
Höhe:	260 mm
Energieschutzeigenschaften:	Over voltage, Under voltage
Betriebstemperatur:	0 - 40 °C
Relative Luftfeuchtigkeit in Betrieb:	0 - 95 %
Zertifizierung:	TAA\nUL1778
Kabellänge:	1.8 m
LED-Anzeigen:	Ja
Temperaturbereich bei Lagerung:	-15 - 50 °C
Luftfeuchtigkeit bei Lagerung:	0 - 95 %
Schnittstelle:	USB; DB9
Formfaktor:	Tower
Ausgangsleistung:	650 W
Eingangsfrequenz:	50/60 Hz
Leistungsfaktor:	0.6
Anzahl der AC-Ausgänge:	8 AC-Ausgänge
Eingangs-Betriebsspannung (min):	83 V
Eingangs-Betriebsspannung (max):	145 V
Ausgangskapazität:	1.05 kVA
Ausgangs-Betriebsspannung (min):	120 V
Ausgangs-Betriebsspannung (max):	120 V
AC-Steckertypen:	NEMA 5–15R
Typische Backup-Zeit bei halber Belastung:	19 min
Typische Backup-Zeit bei voller Belastung:	7 min
Nominale Eingang Spannung:	120 V
Nominale Ausgang Spannung:	120 V
Hot-Swap-Batterie:	Ja
Überspannungsschutz-Funktionen:	Network, Telephone
Anstieg der Energiemenge:	690 J