AXESS AXDIS-GM13 Bedienungsanleitung

Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr AXESS AXDIS-GM13 (8 Seiten) in der Kategorie niet gecategoriseerd. Dieser Bedienungsanleitung war fĂĽr 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
AXDIS-GM13
I N S TA L L AT I O N I N S T R U C T I O N S
AxxessInterfaces.com © COPYRIGHT 2024 METRA ELECTRONICS CORPORATION REV. 1/5/24 INSTAXDIS-GM13
INTERFACE FEATURES
TOOLS & INSTALLATION ACCESSORIES REQUIRED
• Crimping tool and connectors, or solder gun,
solder, and heat shrink • Tape
• Wire cutter • Zip-ties
TABLE OF CONTENTS
Connections 2-3 ........................................................
Installation 3 .............................................................
Programming 4 .........................................................
Adjusting the AXDIS-GM13 4 ....................................
Steering wheel control settings 5-7 .......................
- L.E.D. feedback 5 ....................................................
- Changing radio type 5 ...........................................
- Remapping 6 ..........................................................
- Dual assignment instructions 7 ............................
Troubleshooting.....................................................8
GM Data Interface with SWC 2005-2011
• Designed for amplified models
• Provides accessory power (12-volt 10-amp)
• Retains R.A.P. (retained accessory power)
• Provides NAV outputs (parking brake, reverse, speed sense)
• Retains audio controls on the steering wheel
• Retains OnStar®
• Retains balance and fade
• Micro-B USB updatable
INTERFACE COMPONENTS
• AXDIS-GM13 interface
• AXDIS-GM13 harness
• 16-pin harness
• 3.5mm adapter
CADILLAC
STS 2005-2011 ..............................................................
Visit for up-to-date
AxxessInterfaces.com
vehicle specific applications.
ATTENTION: With the key out of the
ignition, disconnect the negative battery
terminal before installing this product. Ensure
that all installation connections, especially the
air bag indicator lights, are plugged in before
reconnecting the battery or cycling the ignition
to test this product.
NOTE: Refer also to the instructions included
with the aftermarket radio.
Product Info
2
Front
Rear
Sub
AUX-IN
Rear View
SWC
Aftermarket Radio
Vehicle Connectors
Interface
22-Pin
16-Pin
Red - Accessory power
Orange/White - Illumination
Blue/Pink - VSS/Speed-Sense
Green/Purple - Reverse signal
Light Green - Parking brake
Gray - Front right speaker +
Gray/Black - Front right speaker -
White - Front left speaker +
White/Black - Front left speaker -
Green (NOT USED) -
Green/Black (NOT USED) -
Purple (NOT USED) -
Purple/Black (NOT USED) -
Blue/White - Amp turn on from radio
Brown (NOT USED) -
Radio Connections
Yellow wire to the battery wire
Black wire to the ground wire
Blue wire to the power antenna wire
From the AXDIS-GM13 harness to the aftermarket radio
CONNECTIONS
3
REV. 1/5/24 INSTAXDIS-GM13
CONNECTIONS (CONT )
INSTALLATION
With the key in the off position:
• Connect the , and the , into the .16-pin harness AXDIS-GM13 harness AXDIS-GM13 interface
Attention! AXDIS-GM13 harness Do not connect the to the wiring harness in the vehicle just yet.
Attention!
If retaining steering wheel controls, ensure that the jack/wire is connected to the radio before
proceeding. If this step is skipped, the interface will need to be reset for the steering wheel controls to function.
3.5mm jack steering wheel control retention:
• The 3.5mm jack is to be used to retain audio controls on the steering wheel.
• Connect the to the male 3.5mm SWC jack For the radios listed below: 3.5mm adapter
from the . Any remaining wires tape off and disregard.AXDIS-GM13 harness
• Connect the steering wheel control wire, normally , to the Eclipse: Brown Brown/
White wire of the connector. Then connect the remaining steering wheel control
wire, normally , to the wire of the connector.Brown/White Brown
•
Metra OE: (Gray) Brown Connect the steering wheel control Key 1 wire to the wire.
• Connect the Kenwood or select JVC with a steering wheel control wire: Blue/
Yellow Brown wire to the wire.
Note:
If your Kenwood radio auto detects as a JVC, manually set the radio type to
Kenwood. See the instructions under changing radio type.
•
XITE: Brown Connect the steering wheel control SWC-2 wire from the radio to the wire.
•
Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AXSWCH-PAR (sold
separately), and then connect the 4-pin connector from the AXSWCH-PAR into the radio.
Note:
The radio must be updated to rev. 2.1.4 or higher software.
•
Universal “2 or 3 wire” radio: Connect the steering wheel control wire, referred to
as Key-A or SWC-1, to the wire of the connector. Then connect the remaining Brown
steering wheel control wire, referred to as Key-B or SWC-2, to the wire Brown/White
of the connector. If the radio comes with a third wire for ground, disregard this wire.
Note:
After the interface has been programmed to the vehicle, refer to the
manual provided with the radio for assigning the SWC buttons. Contact the radio
manufacturer for more information.
• For all other radios: AXDIS-GM13 harness Connect the 3.5mm jack from the into
the jack on the aftermarket radio designated for an external steering wheel control
interface. Please refer to the aftermarket radios manual if in doubt as to where the
3.5mm jack connects.

Produktspezifikationen

Marke: AXESS
Kategorie: niet gecategoriseerd
Modell: AXDIS-GM13

Brauchst du Hilfe?

Wenn Sie Hilfe mit AXESS AXDIS-GM13 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung niet gecategoriseerd AXESS

Bedienungsanleitung niet gecategoriseerd

Neueste Bedienungsanleitung fĂĽr -Kategorien-