JL Audio 5i Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für JL Audio 5i (2 Seiten) in der Kategorie Autoverstärker. Dieser Bedienungsanleitung war für 10 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
6.62 in
168 mm
11.32 in
287 mm
5.53 in
141 mm
2.12 in
54 mm
10.22 in
260 mm
CONNECTION GUIDE
1000W 5-Channel Class D System Amplier
with Integrated DSP
with
Thank you for purchasing a JL Audio amplifier for your sound system.
Your amplifier has been designed and manufactured to exacting
standards in order to ensure years of musical enjoyment. For maximum
performance, we highly recommend that you have your new amplifier
installed by an authorized JL Audio dealer. Your authorized dealer has
the training, expertise and installation equipment to ensure optimum
performance from this product. Should you decide to install the amplifier
yourself, please take the time to read this manual thoroughly to familiarize
yourself with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this manual or any
aspect of your amplifier’s operation, please contact your authorized JL
Audio dealer for assistance. If you need further assistance, please contact
the JL Audio Technical Support Department at technical@jlaudio.com or
call (954) 443–1100 during business hours.
Installation Applications
This amplifier is designed for operation with 12 volt, negative-
ground electrical systems. Using this product in systems with positive
ground and/or voltages other than 12V may result in damage to the
product and will void the warranty. This product is not certified or
approved for use in aircraft.
Product Description
This is a five-channel, Class D system amplifier equipped with the second
generation of JL Audio’s NexD2™ high-speed switching technology.
It is engineered to deliver reference-grade audio amplification with
outstanding efficiency and unprecedented, built-in processing power.
Instead of traditional analog processing controlled by knobs and switches,
VXi amplifiers feature an integrated DSP (Digital Signal Processor). The
amplifier and its integrated DSP are configured using an external device
(PC, Tablet or Phone), with the appropriate JL Audio TüN™ application
installed. (See What is TĂĽN? section for more info.)
Planning Your Installation
It is important that you take the time to read this manual thoroughly
and that you plan your installation carefully. It is very easy to damage
expensive vehicle systems in modern automobiles. Never assume that you
have found appropriate wires without consulting a reliable wiring diagram
or without analyzing with proper test equipment. If you are uncomfortable
or unfamiliar with reading diagrams or testing methods, please enlist the
services of your authorized JL Audio dealer to perform the installation.
Your authorized dealer has the training, expertise and installation
equipment to ensure optimum performance from this product.
The
following are some considerations that you must take into account when
planning your installation.
Safety Considerations
• Install your amplifier in a dry, well-ventilated location that
does not interfere with your vehicle’s safety equipment
(air bags, seat belt systems, ABS brake systems, etc.).
• Do not mount the amplifier in the engine
compartment or in any areas of extreme heat.
• Securely mount the amplifier so that it does not come
loose in the event of a collision/sudden jolt or as a result
of repeated vibrations during normal operation.
• Check before drilling to make sure that you will not be drilling into
a fuel tank, gas/brake line, wiring harness, or other vital system.
• Do not run system wiring outside or underneath the
vehicle/vessel. This is an extremely dangerous practice,
which can result in severe damage/injury.
• Take the necessary precautions when making
connections to the vehicle’s battery.
• Protect all system wires from sharp edges by carefully routing them,
tying them down and using grommets and loom where appropriate.
• Secure all wiring as needed, using cable ties or wire clamps
to protect them from moving parts and sharp edges.
Cooling Efficiency Considerations
The outer shell of your JL Audio amplifier is designed to remove heat
from the amplifier circuitry. For optimum cooling performance, this outer
shell should be exposed to as large a volume of air as possible. Enclosing
the amplifier in a small, poorly ventilated chamber can lead to excessive
heat build-up and degraded performance. If an installation calls for an
enclosure around the amplifier, we recommend that this enclosure be
ventilated with the aid of a fan. In normal applications, fan-cooling is not
necessary. If mounting the amplifier under a seat, make sure there is at
least 1 inch (2.5 cm) of space above the amplifier’s outer shell to permit
proper cooling.
What is Included
(1) Amplifier (1) Power Connector
(1) Analog Input/Pre-Out Harness (1) Speaker Output Harness
(1) JL Audio Badge (1) Subwoofer Output Connector
(1) USB A/B Cable (6 ft./1.8 m) (4) Corner Caps
(2) Black Hex Cap Machine Screws (1) Corner Cap Tool
(2) Silver Thumbscrews (1) 2.5 mm Hex Wrench
(1) Connection Guide (1) 3 mm Hex Wrench
JL Audio Badge
To complement the amplifier’s mounting orientation, the logo badge
includes a recessed key feature allowing it to be affixed at 90 degree
increments on the amplifier’s top. To install, remove the adhesive backing
and press the badge at the desired orientation.
Corner Cap Installation and Removal
The corner caps are designed to conceal the amplifier’s mounting holes
and hardware. To install, simply press a corner cap into each mounting
hole. To avoid scratching the amplifier’s chassis during removal, use the
included, plastic corner cap tool and lift below each cap.
Making Connections
VXi amplifiers utilize removable plugs and harnesses to make the
following connections:
• Power Connector and Subwoofer Output Connector
To connect the power, ground, remote turn-on and subwoofer output
wires to the amplifier, back out the set screws on each connector using
the supplied hex wrenches. Strip back 3/8 inch (10 mm) of insulation from
the end of each wire and insert the bare wire into the receptacle on the
power connector plug, seating it firmly so that no bare wire is exposed.
While holding each wire in place, tighten each set screw firmly, taking
care not to strip the head of the screw. Install each connector by plugging
it into the amplifier’s corresponding receptacle, pushing firmly.
• Analog Input/Pre-Out Harness
This harness includes connections for Signal Input (RCA plugs), Preamp
Outputs (RCA plugs), Remote Turn-On Output (wire lead) and Valet Input
(wire lead). Select either the included black hex cap machine screws or
the silver thumbscrews to secure the Analog Input Harness connector to
the amplifier.
• Speaker Output Harness
This harness has output wire leads to connect with speaker cables.
Turn-On Mode
VXi amplifiers can be switched on and off using one of three methods,
configured by the “Turn On Mode” setting in the TüN™ Software Interface.
Refer to the table below for detailed info and decide which option is best
suited for your specific system.
Setting Mode Function Connection
Remote Conventional
(Preferred)
Turn-on/off controlled by your
source unit.
Connect your source unit’s
+12V remote turn-on output to
the Power Connector’s Remote
Turn-On Input connection.
DC
Offset
DC Offset
Sensing
(Auto)
Automatically turns on by
detecting the presence of small
DC signal in OEM audio outputs
and turns off (within 5 minutes)
after the signal is removed.
This circuit senses the Analog
Input 1 only. Note: The sensitivity
of this circuit is designed for
high-level (speaker level) signals,
not for low-level (preamp level)
signals. Make sure the OEM
audio outputs contain midrange
signals.
Signal
Signal
Sensing
(Auto)
Automatically turns on by detecting
full-range OEM audio signals and
turns off (within 5 minutes) after
the signal is removed (varies,
depending on input signal levels).
3 Speaker Output Harness
Connect the speaker output leads to the corresponding speaker wires.
4 Subwoofer Output Connector
Connect the subwoofer wires to the corresponding terminals.
5 JLid-COMM
Connect optional accessories (VXi-BTC, VXi-HUB, etc.) to this port.
6 JLid-CTRL
Connect optional DRC (Digital Remote Controller) wired controllers
to this port.
7 SD + Reset
Lift the dust cover to access the following utility functions:
Reset Buttons: Use a small pin to perform the following:
Reboot Amp - Press and release the right button.
Factory Reset (wipe memory, reboot amp) - Press and hold the left
button for 7 seconds.
Micro SD Slot: For service/future expansion.
8 USB
This USB A/B port permits connection to a computer for configuration
and tuning, using the TüN™ Software.
9 DIGITAL-In
Toslink port accepts 2-channel digital audio signal from any optical
(S/PDIF) digital output, with a sample rate up to 192 kHz.
10 DIGITAL-Out
Provides a digital audio output (24 bit/96 kHz) that is not susceptible to
RF interference or noise-generating electrical conditions. By default, this
is a pass-through audio output, with no signal processing applied, and
intended for use with other equipment that have an optical (Toslink)
digital audio input (S/PDIF) port. Using the TüN™ Software Interface, you
may configure this output’s routing, equalization, output level and DRC
control functionality.
1 Power Connector
The VX1000/5i’s “+12 VDC” and “Ground” connections are designed to accept
up to 2 AWG copper wire. Note: Copper Clad Aluminum (CCA) wire is not
recommended. 4 AWG is the minimum copper wire size for this amplifier.
A. Run copper wire from the positive (+12V) battery post to the amplifi-
er mounting location. If additional amplifiers are being installed, run
the appropriate gauge copper wire for the combined, maximum cur-
rent draw, and install a fused distribution block near the amplifiers.
B. An appropriate fuse (sold separately) at the main power wire(s) is
vital for vehicle safety. This fuse must be installed within 18 inches
(45 cm) of the battery post connection. If this is the only device con-
nected to this main wire, use a 80 A fuse. Do not install the fuse until
the power wire has been securely connected to the amplifier.
C. The ground connection should be made to a clean, solid metal
grounding point using copper wire, and kept as short as possible.
The metal surface of the grounding point should be sanded to create
a clean, metal-to-metal connection. For optimal grounding, we
recommend using a JL Audio ECS master ground lug (XB-MGLU). All
ground connections (source unit and amplifiers) should be made
at the same location.
D. The remote connection should be made to the source unit’s positive
(+12V) remote turn-on output. If your source unit does not have a
dedicated remote turn-on output, consider one of the alternative
turn-on options. (See Turn-On Mode section for more info.)
2 Analog Input/Pre-Out Harness
The Analog Input Harness accepts the following connections:
Line-Level Analog Inputs: Six female RCA jacks feed a differential-
balanced input section, providing a high degree of input flexibility, and
retaining superior noise rejection. This type of input architecture also
allows the VX1000/5i to cleanly accept any analog audio signals up to 16
VRMS, without using a line-output converter.
Preamp Outputs: Two female, RCA jacks deliver line-level, analog audio
outputs (Max 4 V RMS) that are compatible with most types of aftermarket
equipment. These are configured with the TüN™ Software Interface.
Remote: This connection provides a positive (+12V) turn-on voltage
(475 mA limit) to activate other aftermarket equipment (similar to an
aftermarket head unit’s remote turn-on lead).
Valet: When connected to negative ground, this connection activates the
Valet Mode Preset and will remain active until the ground connection is
removed. This preset is configured using the TüN™ Software Interface and
will override any DRC controlled preset.
1 2 3
5 6 798 10
4
Limited Warranty – Amplifiers (USA)
JL Audio warrants this product to be free of defects in materials and workmanship
for a period of two (2) years from the original date of purchase. This warranty is
not transferable and applies only to the original purchaser from an authorized
JLAudio dealer. Should service be necessary under this warranty for any reason due
to manufacturing defect or malfunction, JL Audio will (at its discretion), repair or
replace the defective product with new or remanufactured product at no charge.
Damage caused by the following is not covered under warranty: accident, misuse,
abuse, product modification or neglect, failure to follow installation instructions,
unauthorized repair attempts, misrepresentations by the seller. This warranty does
not cover incidental or consequential damages and does not cover the cost of
removing or reinstalling the unit(s). Cosmetic damage due to accident or normal
wear and tear is not covered under warranty.
Warranty is void if the product’s serial number has been removed or defaced.
Any applicable implied warranties are limited in duration to the period of the
express warranty as provided herein beginning with the date of the original
purchase at retail, and no warranties, whether express or implied, shall apply to
this product thereafter. Some states do not allow limitations on implied warranties,
therefore these exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights, which vary from state to state.
If you need service on your JL AUDIO product:
All warranty returns should be sent to JL Audio ’s Amplifier Service Facility
freight-prepaid through an authorized JL Audio dealer and must be accompanied
by proof of purchase (a copy of the original sales receipt). Direct returns from
consumers or non-authorized dealers will be refused unless specifically authorized
by JL Audio with a valid return authorization number. Warranty expiration on
products returned without proof of purchase will be determined from the
manufacturing date code. Coverage may be invalidated as this date is previous
to purchase date. Non-defective items received will be returned freight-collect.
Customer is responsible for shipping charges and insurance in sending the
product to JL Audio. Freight damage on returns is not covered under warranty.
For Service Information in the U.S.A. please call
JL Audio Customer Service:
(954) 443-1100 9:00 AM – 5:30 PM (Eastern Time Zone)
JL Audio, Inc.
10369 North Commerce Pkwy. Miramar, FL 33025
(Do not send product for repair to this address)
International Warranties:
Products purchased outside the United States of America are covered
only by that country’s distributor and not by JL Audio, Inc.
V X10 0 0/5i _ M AN _ 0 41118
Connections
Power Connector
Connection Wire Capacity Description
+12 VDC (+) 2 AWG Positive (+12V) Power Connection to Battery
Ground (–) 2 AWG Negative (GND) Chassis Ground Connection
Remote 18 to 10 AWG Positive (+12V) Remote Turn-On Input from Source Unit
Analog Input Harness
Label Plug/Wire
Color Description
Input 1 White RCA Channel 1 Signal Input
Input 2 Red RCA Channel 2 Signal Input
Input 3 White RCA Channel 3 Signal Input
Input 4 Red RCA Channel 4 Signal Input
Pre-Out Left White RCA Preamp Signal Output 1
Pre-Out Right Red RCA Preamp Signal Output 2
Remote Blue Positive (+12V) Turn-On Output (475 mA limit)
Valet Green Negative (GND) Ground Input (activates the Valet Mode Preset)
Speaker Output Harness
Label Wire Color Description
A
White
Ch. 1
(+) Positive Speaker Output Ch. 1&2 Bridged (+)
White/Black (–) Negative Speaker Output
B
Gray
Ch. 2
(+) Positive Speaker Output
Gray/Black (–) Negative Speaker Output Ch. 1&2 Bridged (–)
C
Green
Ch. 3
(+) Positive Speaker Output Ch. 3&4 Bridged (+)
Green/Black (–) Negative Speaker Output
D
Purple
Ch. 4
(+) Positive Speaker Output
Purple/Black (–) Negative Speaker Output Ch. 3&4 Bridged (–)
Subwoofer Output Connector
Connection Wire Capacity Description
SUB + 14 to 10 AWG (+) Positive Subwoofer Output
SUB – 14 to 10 AWG (–) Negative Subwoofer Output
Data Connections
Label Type Description/Use
JLid-COMM RJ45 Jack Optional accessory connections (VXi-BTC, VXi-HUB, etc)
JLid-CTRL RJ45 Jack Optional DRC (Digital Remote Controller) connection
USB USB A/B Port Computer connection to congure TüN™ Software Interface
DIGITAL-In S/PDIF Port 2-channel, optical (Toslink) digital input
DIGITAL-Out S/PDIF Port 2-channel, optical (Toslink) digital output
SD + Reset
Reset Buttons Multifunction use (Reboot/Reset/Device Firmware Update mode)
Micro SD Slot Used for future expansion
Specifications
Amplier Specications
Amplier Topology 2nd-Gen NexD™ High Speed Class D
Power Supply Type Unregulated MOSFET Switching
Operating Voltage 10 - 15V DC
Min. Copper Power/GND Wire 4 AWG
Recommended Fuse 80 A
Standby Current Draw 2.1 mA
Input Voltage Range 200 mV - 16 V RMS
Rated RMS Power @ 14.4V,
<1% THD+N
Main @ 4 Ω
75W x 4
Main @ 2 Ω
100W x 4
Main @ 4 Ω Bridged
200W x 2
Sub @ 4 Ω
400W x 1
Sub @ 3 Ω
500W x 1
Sub @ 2 Ω
600W x 1
Rated RMS Power @ 12.5V,
<1% THD+N
Main @ 4 Ω
60W x 4
Main @ 2 Ω
90W x 4
Main @ 4 Ω Bridged
180W x 2
Sub @ 4 Ω
360W x 1
Sub @ 3 Ω
480W x 1
Sub @ 2 Ω
600W x 1
Frequency Response Main: 12 Hz - 24 kHz (+0, -1dB)
Sub: 12 Hz - 1 kHz (+0, -1dB)
Analog
Inputs
S/N Ratio
(A-weighted, 20 kHz
noise bandwidth)
Main: 99 dB (Referred to rated power),
80 dB (Referred to 1 W)
Sub: 99 dB (Referred to rated power),
72 dB (Referred to 1 W)
Digital
Input
S/N Ratio
(A-weighted, 20 kHz
noise bandwidth)
Main: 100 dB (Referred to rated power),
81 dB (Referred to 1 W)
Sub: 99 dB (Referred to rated power),
73 dB (Referred to 1 W)
Damping Factor Main: >100 / 50 Hz @ 4 Ω, >50 / 50 Hz @ 2 Ω
Sub: >100 / 50 Hz @ 4 Ω, >50 / 50 Hz @ 2 Ω
DSP Specications
Processor AKM AK7738, processing at 24 bit/96 kHz
Analog
Inputs
Type Line-Level, Dierential-Balanced
Number of Channels 6, via harness-mounted female RCA jacks
Digital
Input
Type S/PDIF Optical via chassis-mounted Toslink port
Bit Depth/Sample Rate
Up to 24 bit/192 kHz
Analog
Outputs
Type 2 Line-Level, via harness-mounted female RCA jacks
Max Output Level 4 V RMS
Digital
Output
Type S/PDIF Optical via chassis-mounted Toslink port
Bit Depth/Sample Rate 24 bit/96 kHz
Dimensions
L x W x H 11.32 in x 6.62 in x 2.12 in / 287 mm x 168 mm x 54 mm
What is TĂĽN?
TüN™ is software that you use to configure, tune and control your VXi
amplifier, and other JL Audio DSP products. TüN™ automatically recognizes
what it is connected to, and allows you to make adjustments with a
clear interface specifically set up for that product. TüN™ is available for
download for free in a variety of applications, for computers and most
handheld devices. For more information, visit: jlaudio.com/tun
For Windows® PC or Mac® computers, TüN™ connects via
USB and offers complete control and command of the entire
VXi feature set from the comfort of your desk or driver’s seat.
Software also runs in demo mode, without connected amplifiers,
for offline setup or demo purposes. Test drive it for free!
For iPad or Android tablets. Enjoy the full-featured TüN™ software
experience on your tablet, with the freedom of a wireless connection
via Bluetooth®. Requires VXi-BTC Bluetooth® Communicator.
Wireless connection and streamlined options, for fast and simple
amplifier setup. Download TüN™ Express for iPhone, iPad and Android
phones & tablets. Requires VXi-BTC Bluetooth® Communicator.
+12 VDC - Positive (+12V) Battery Connection
Ground - Negative (–) Ground Connection
Remote - Positive (+12V) Turn-On Input From Source Unit
JLid-COMM - Optional Network Hub or
Bluetooth® Communicator Connection (Sold Separately)
JLid-CTRL - Optional Digital Remote Controller
(DRC) Connection (Sold Separately)
SUB - To Subwoofer(s): (+ and –)
Input 6 - Ch. 6 Input
Input 5 - Ch. 5 Input
Input 2 - Ch. 2 Input
Input 1 - Ch. 1 Input
Pre-Out Right - Analog Preamp Output
Pre-Out Left - Analog Preamp Output
Remote - Turn-On Output (+12V)
Valet - Valet Preset Toggle (–)
Input 4 - Ch. 4 Input
Input 3 - Ch. 3 Input
D - To Speaker(s): (+ and –)
C - To Speaker(s): (+ and –)
B - To Speaker(s): (+ and –)
A - To Speaker(s): (+ and –)
DIGITAL-In - From Optical Digital (S/PDIF) Source
DIGITAL-Out -
To Optical Digital (S/PDIF) Input on Next Device
USB A/B Cable -
To Computer with TüN™ software installed
SPEAKER
OUTPUTS
ABCD + SUB –
Wiring Diagram - VX1000/5i
Standard CAT5 Network Cables
Optical Audio Cables
Included
Not Included
ANALOG INPUTS / PRE-OUTS
LED Status/Condition Reporting
LEDs located on the chassis top and connection panel are used to
communicate amplier status and condition. Refer to the table below for
the location and meaning for each behavior.
LED / Location Behavior Status/Condition›
LED Ring /
Amplier Top
Flashing Blue Critical Voltage
Flashing Red Critical Temperature
Flashing Yellow Excessive Current
Upper Left LED /
JLid-COMM Port
and
JLid-CTRL Port
Green Detecting JLid™ Device
Blue JLid™ Connection Success
Yellow Invalid JLid™ Device
Flashing Red Excessive Current
Upper Right LED /
JLid-COMM Port Flashing Red
Critical Voltage/Temperature
Excessive Remote Output Current
Upper Right LED /
JLid-CTRL Port Green Active TüN™ Connection
Produktspezifikationen
| Marke: | JL Audio |
| Kategorie: | Autoverstärker |
| Modell: | 5i |
Brauchst du Hilfe?
Wenn Sie Hilfe mit JL Audio 5i benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Autoverstärker JL Audio
23 August 2024
23 August 2024
23 August 2024
23 August 2024
23 August 2024
22 August 2024
22 August 2024
22 August 2024
22 August 2024
21 August 2024
Bedienungsanleitung Autoverstärker
- Autoverstärker Sony
- Autoverstärker MarQuant
- Autoverstärker Blaupunkt
- Autoverstärker Kenwood
- Autoverstärker Autotek
- Autoverstärker Auna
- Autoverstärker Caliber
- Autoverstärker Pioneer
- Autoverstärker JVC
- Autoverstärker Hifonics
- Autoverstärker Dual
- Autoverstärker Alpine
- Autoverstärker Rockford Fosgate
- Autoverstärker AXTON
- Autoverstärker Peiying
- Autoverstärker Audison
- Autoverstärker Macrom
- Autoverstärker Infinity
- Autoverstärker Phoenix Gold
Neueste Bedienungsanleitung fĂĽr -Kategorien-
12 Oktober 2024
9 Oktober 2024
7 Oktober 2024
27 August 2024
27 August 2024
27 August 2024
27 August 2024
27 August 2024
27 August 2024
27 August 2024