Inovonics EN1262HT Bedienungsanleitung

Inovonics Bewegungsmelder EN1262HT

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Inovonics EN1262HT (3 Seiten) in der Kategorie Bewegungsmelder. Dieser Bedienungsanleitung war für 22 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/3

12.9.21 357-00056-01 Rev A © Inovonics, 2021 - www.inovonics.com

EN1262HT High Traffic Motion Detector

Installation and Operation Manual

1 Overview

The EN1262HT high traffic motion detector solves the battery limitation

problems of motion sensors in commercial applications through an

intelligent sleep timer and low current technology. It features a pet immune

PIR detection element, and wall and housing tamper switches.

1.1 Inovonics Contact Information

If you have any problems with this procedure, contact Inovonics technical

support:

• E-mail: support@inovonics.com.

• Phone: (800) 782-2709; (303) 939-9336.

2 Installation and Startup

2.1 Installation Notes

• These products are designed to be maintained by professional

security technicians.

• Products are tested for indoor use.

• All products should be manually tested weekly.

2.2 Mount the Housing and Install the Battery

1. Loosen the captive housing screw.

2. Open the housing.

Figure 1 Open the housing

3. Remove the EN1262HT from the mounting bracket per Figure 2.

Figure 2 Remove the EN1262HT from the mounting bracket

4. Noting the detection coverage in Figure 3, determine mounting location.

• Avoid areas facing direct sunlight, areas that may change temperature

rapidly, and areas where there are air ducts or substantial airflows.

• The recommended mounting height is 6.5 feet to 7.5 feet

(2.1 to 2.3 m).

Figure 3 EN1262HT detection coverage area

For product and installation videos visit us at

www.inovonics.com/videos or use the QR

code below.

TOP VIEW

along side wall

7.2 ft

26.2 ft

6.6 ft

13.1 ft

89°

37 ft

26.2 ft

37 ft 26.2 ft

Side VIEW

6.6 ft

13.1 ft

26.2 ft

12.9.21 357-00056-01 Rev A © Inovonics, 2021 - www.inovonics.com 2

5. Use the included mounting screws to mount the EN1262HT.

• To mount on the wall, see Figure 4.

• To mount in a corner, see Figure 5.

Figure 4 Wall mount configuration

Figure 5 Corner mount configuration

6. Install the battery per Figure 6.

Figure 6 Install the battery

Note: When disposing of this device or depleted batteries, please do so in

accordance with federal, state and local regulations.

2.3 Select Pulse Count

The pulse count options provides control for difficult operating

environments. Automatic pulse count is recommended for reliable

operation in environments subject to temperature fluctuation that can cause

false alarms. The single pulse count mode is more sensitive to minor

temperature variations, and should be used in sites where variant heat

sources will not cause alarms. Automatic pulse count is the factory default

because it allows more reliable operation in environments subject to

temperature fluctuation. To select pulse count:

1. Press the tamper button five times within three seconds.

Figure 7 Press the tamper button

2. Wait for the green LED to blink five times, then:

• Press the tamper button one time within three seconds to select single

pulse count.

12.9.21 357-00056-01 Rev A © Inovonics, 2021 - www.inovonics.com 3

• Press the tamper button two times within three seconds to select

automatic pulse count.

3. Confirm your selection.

• The green LED will blink once to indicate single pulse count has been

selected; twice to confirm automatic pulse count has been selected.

2.4 Select Fixed/Variable Sleep Time

The sleep time setting provides control for normal or high-traffic operating

environments. When set to fixed, if the EN1262HT senses motion, it will

transmit an alarm, then enter sleep mode for 180 seconds; if motion is

sensed when the sleep time has expired, the EN1262HT will transmit

another alarm. When set to variable, if the EN1262HT senses motion, it will

transmit an alarm, then enter sleep mode for 180 seconds; if motion is

sensed before the sleep time has expired, the EN1262HT will restart the

180 second interval. Variable sleep time is the default setting as shipped

from the factory. To select sleep time:

1. Press the tamper button four times within three seconds.

2. Wait for the green LED to blink four times, then:

• Press the tamper button one time within three seconds to select fixed

sleep time.

• Press the tamper button two times within three seconds to select

variable sleep time.

3. Confirm your selection.

• The green LED will blink once to indicate fixed sleep time has been

selected; twice to confirm variable sleep time has been selected.

2.5 Register the Transmitter

The EN1262HT must be registered with the system receiver in order to be

monitored and supervised. Each EN1262HT has a unique factory-

programmed identification number. Refer to the receiver, network

coordinator or control panel installation instructions for details on

registering a transmitter.

1. When prompted to register the device, remove and replace the battery.

Note: Registration can only occur upon battery installation.

2. Replace the housing cover.

Caution: The EN1262HT should be tested after registration to ensure

operation. To test the EN1262HT, activate each of the conditions and

ensure an appropriate response.

3 Test the EN1262HT

When in walk test mode the test LED will light red every time the

EN1262HT senses motion. The unit will not transmit alarm signals during

this test period. Once initiated, the walk test will last for ten minutes and

then the EN1262HT will automatically return to normal operation. To initiate

a walk test:

1. Press the tamper button three times within three seconds.

Note: The test LED only lights red during the walk test.

4 Specifications

Dimensions: 5.2” x 2” x 2.4” (132 mm x 50 mm x 60 mm).

Weight: 4.2 ounces (120 grams)

Operating temperature: 32°F to 120°F (0°C to 49°C).

Humidity: 0 - 93% (non-condensing).

Battery: Two Energizer L91 AA lithium 1.5V batteries.

Typical battery life: Three years.

Tamper: Housing and wall.

PIR: Quad element PIR.

Coverage area: 26’ (8m).

Warm up period: 40 seconds.

Check-in time: Three minutes.

5 Television and Radio Interference

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

6 FCC Part 15 and Innovation, Science and

Economic Development Canada (ISED)

Compliance

This device complies with part 15 of the FCC Rules, and ISED license-

exempt RSS standard(s). Operation is subject to the following two

conditions: (1) this device may not cause interference, and (2) this device

must accept any interference that may cause undesired operation of the

device.

Le présent appareil est conforme aux CNR Innovation, Sciences et

Développement économique Canada applicables aux appareils radio

exempts de licence. L'exploitation est autorisée aux deux conditions

suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur

de l'appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d'en compromettre le fonctionnement.

Caution: Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the

equipment.

7 Radiation Exposure Limits

7.1 FCC

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment. In order to avoid the possibility of exceeding the

FCC radio frequency exposure limits, human proximity to the antenna shall

not be less than 20 cm during normal operation and must not be co-located

or operating in conjunction with any other antenna or transmitter.

7.2 ISED

This equipment complies with ISED RSS-102 radiation exposure limits set

forth for an uncontrolled environment. This transmitter must be installed to

provide a separation distance of at least 20 cm from all persons and must

not be co-located or operating in conjunction with any other antenna or

transmitter.

Cet équipement est conforme avec ISED RSS-102 des limites d'exposition

aux rayonnements définies pour un environnement non contrôlé. Cet

émetteur doit être installé à au moins 20 cm de toute personne et ne doit

pas être colocalisé ou fonctionner en association avec une autre antenne

ou émetteur.

Produktspezifikationen

Marke:	Inovonics
Kategorie:	Bewegungsmelder
Modell:	EN1262HT
Breite:	60 mm
Tiefe:	50 mm
Gewicht:	120 g
Produktfarbe:	Weiß
Übertragungstechnik:	Kabellos
Akku-/Batterietyp:	AA
Höhe:	132 mm
Energiequelle:	Akku
Befestigungstyp:	Decke/Wand
Betriebstemperatur:	0 - 49 °C
Relative Luftfeuchtigkeit in Betrieb:	0 - 93 %
Anzahl unterstützter Akkus/Batterien:	2
Akku-/Batteriespannung:	1.5 V
Nachhaltigkeitszertifikate:	Federal Communications Commission (FCC), RoHS
Funkfrequenz:	902 - 928 MHz
Batterie Lebensdauer:	3 Jahr(e)
Sensor-Typ:	Passiver Infrarot-Sensor (PIR)
Distanzerfassung:	8 m