HQ EL-PIR20 Bedienungsanleitung

HQ Bewegungsmelder EL-PIR20

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für HQ EL-PIR20 (59 Seiten) in der Kategorie Bewegungsmelder. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/59
15-11-2011
EL-PIR20
MANUAL (p. 2)
Wall Sensor Switch
ANLEITUNG (S. 6)
Wandbewegungsmelder
MODE DEMPLOI (p. 10)
Interrupteur mural à détecteur
GEBRUIKSAANWIJZING (p. 14)
Muursensorschakelaar
MANUALE (p. 18)
Interruttore a sensore da Parete
MANUAL DE USO (p. 22)
Interruptor de pared con sensor
HASZNÁLATI ÚTMUTATÓ (o. 26.)
Fali mozgásérzékelő kapcsoló
KÄYTTÖOHJE (s. 30)
Liiketunnistinkytkin seinämalli
BRUKSANVISNING (s. s34)
Vägg sensor brytare
NÁVOD K POUŽITÍ (s. 38)
Nástěnný bezdotykový spínač
MANUAL DE UTILIZARE (p. 42)
Întrerupător pentru senzor de perete
ΕΓΧΕΙΡΙΔΙΟ XPHΣ ΣH (σελ. 46)
Επιτοίχιος διακόπτης αισθητήρας
BRUGERVEJLEDNING (s. 50)
Kontakt til vægsensor
VEILEDNING (s. 54)
Veggsensorbryter
2
ENGLISH
Wall Sensor Switch
FUNCTION:
• Multi-function: It has ON, OFF, light-control, high sensitive sound control, long distance and wide
range infrared detection functions.
• Practicality: by the light-control it can control the sound-control and the ambient-light when the
sensor works. It can work in various day and night ambient-lights; it also can work only in low
ambient-light. Time-delay can be manually adjusted to a stipulated range; infrared induction and
sound control sensitivity can also be controlled manually.
• Wide working voltage: 90 V AC ~ 240 V AC, 50 ~ 60 Hz.
• Convenient installation: There are two installation modes to choose from. It can be installed in a
circular or square junction box; the sensor can be fixed to the circular junction box with two screws
or it can be fixed to the special installation shelf on the sensor. When the junction box installation
orientation is correct, the EL-PIR20 should be flat.
• Detection indication: The indicator lamp flashes once every time it detects motion.
• Multi-working mode: You can select ON, OFF, infrared detection, infrared detection and sound
control modes. If you select infrared detection plus sound control mode, the lamp will turn on every
time motion is felt by the sensor.
Correct moving orientation Incorrect moving orientation
INSTALLATION:
• Shut off the power.
• Loosen the connection column on the bottom of the sensor, attach the wire into the connection hole
and tighten the screws.
• Remove the surface cover of the sensor; connect the sensor into the connection box.
• If you want to install it in a square connection box, push the screw into the installation hole, block on
radiator to aim at the installation hole on connection box, then tighten the screw; if you want to
install it in the circular connection box you can use the same method as the square box. Adjust the
sensor’s position, tighten the surface screw, then the fixing arm will open automatically, fasten the
connection box.
• Switch on the power and then test.
3
CONNECTION WIRING DIAGRAM (see figure on right)
TEST:
• Set the function switch to “ON”, set “SENS” to maximum, “MIC” to maximum; “LUX” to maximum,
“TIME” to minimum.
• Switch on the power, the lamp should be on.
• Set the function switch to “OFF”. After 30 sec the lamp should be off; all the functions should be in
the “stop” state.
• Set the function switch to “PIR”. After 30 sec the inductor lamp will go on, after 20 sec when there is
inductor signal whether the lamp is on or not. Under no inductor signal condition, the lamp should
go off within 5~10 sec, and the lamp should go on again after 5 sec. Set “LUX” to minimum, after it
has gone off when there is no inductor signal condition, the lamp should be off during the daytime,
but if you use an opaque object to cover the sensor, the lamp should go on, then go off within
5~10 sec.
• Set the function switch to “+MIC”, “LUX” to maximum, then when the sensor is in the infrared
detection +sound control mode, cover the detector. If the lamp is on, under the no inductor signal
condition, the lamp should go off after 5~10 sec. After 5 sec, if you clap your hands, the lamp should
go on, then off again after 5~10 sec (no inductor signal).
SPLAY BOLT
MOUNTING HOLE
FIXED ARM
OPEN FACEPLATE
Sensor switch

Produktspezifikationen

Marke: HQ
Kategorie: Bewegungsmelder
Modell: EL-PIR20

Brauchst du Hilfe?

Wenn Sie Hilfe mit HQ EL-PIR20 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Bewegungsmelder HQ

HQ

HQ EL-PIRLA80 Bedienungsanleitung

5 August 2024
HQ

HQ EL-PIRLA90 Bedienungsanleitung

5 August 2024
HQ

HQ EL-PIRLA30 Bedienungsanleitung

3 August 2024
HQ

HQ EL-PIR70 Bedienungsanleitung

23 Juli 2024
HQ

HQ EL-PIR20 Bedienungsanleitung

19 Juli 2024

Bedienungsanleitung Bewegungsmelder

Neueste Bedienungsanleitung für -Kategorien-

Orbis

Orbis Circumat Bedienungsanleitung

10 Oktober 2024
Vemer

Vemer Sensor 360L Bedienungsanleitung

6 Oktober 2024
Perel

Perel EMS103 Bedienungsanleitung

3 Oktober 2024
Renkforce

Renkforce 1362921 Bedienungsanleitung

27 September 2024
Busch-Jaeger

Busch-Jaeger Sicherheitstechnik 6800-0-2521 Bedienungsanleitung

17 September 2024
Busch-Jaeger

Busch-Jaeger 2CKA006200A0056 Bedienungsanleitung

15 September 2024
DSC

DSC PG9862 Bedienungsanleitung

14 September 2024
Maxsa

Maxsa 40234 Bedienungsanleitung

11 September 2024
Maxsa

Maxsa 43218 Bedienungsanleitung

11 September 2024
ORNO

ORNO OR-CR-233 Bedienungsanleitung

10 September 2024