Hitec LINX_SPORT Bedienungsanleitung
Hitec
Funksteuerung
LINX_SPORT
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Hitec LINX_SPORT (6 Seiten) in der Kategorie Funksteuerung. Dieser Bedienungsanleitung war für 28 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/6
www.hitecrcd.com
MADE IN PHILIPPINES
www.hitecrcd.com
Ergonomic Pistol Grip Design
2 Channel AM Proportional System
2 Channel Servo Reversing Switches
2 LED Battery Status Indicator
Nicad Battery Charging Jack
Ergonomic Pistol Grip Design
2 Channel AM Proportional System
2 Channel Servo Reversing Switches
2 LED Battery Status Indicator
Nicad Battery Charging Jack
www.hitecrcd.com
AM
PR OPOR TI ONA L
STEE.
THRO.
HIGH
LOW
ON
I. Introduction
II. Features and Specifications
III. System Layout
IV. Setting and Operation
1. Transmitter
a. Loading Batteries
b. Reading the LED Battery Indicators
c. Recharging Nicd Batteries
d. Transmitter Antenna
e. Changing Crystals
2. Installation of Receiver and Servos
a. Using Separate Power Source for the Receiver
b. Battery Eliminator Circuit with Mechanical Speed Control
c. Connection with Electronic Speed Control
3. Transmitter, Receiver and Servo Settings
a. Checking Operation of the Servo
- Steering Servo Settings
- Steering Servo Trim Setting
b. Throttle Servo Settings
- Using Mechanical Speed Control
- Using Electronic Speed Control
- Using Throttle Servo for Gas Powered Vehicles
Table of Contents
Thank you for purchasing the Lynx Sport, 2 Channel, Pistol Grip, and AM Radio Control
System. The Lynx Sport Radio is made of high quality, technically advanced components
designed to achieve top performance from your RC vehicle. Team up with Hitec Racing
and see that quality and performance doesn't have to cost a fortune!
I. Introduction
II.Features and Specifications
- Pistol Grip 2 Channel AM Proportional System
- Servo Reversing Switches (Both Channels)
- 2 L.E.D. Battery Status Indicator
- Nicd Battery Charging Jack
- Power Output: 500Mw
- Current Drain: 180 mA
III. System Layout
THR
NORREV NORREV
ST
REVERSESWITCH
Steering Reverse Switch
Steering Trim
Antenna
TX Crystal Holder
Power Switch Throttle Trigger
Steering Wheel
LED Battery Indicator
Charging jack
Battery cover
Throttle Trim
Throttle Reverse Switch
1 2
www.hitecrcd.com
AM
PROPORTIONAL
STEE.
THRO.
HIGH
LOW
ON
3 4
IV. Setting and Operation
1. Transmitter
a. Loading Batteries
You may use either Alkaline or Nicad "AA" size batteries.
- Push the bottom battery cover in the direction of the arrow then lift up the cover
- Load 8 AA batteries (Be sure the polarity is correct)
- Reinstall battery cover
- Nicds should be charged with the Hitec CG-22 or CG-25A charger for
minimum 12 hours before use
1
2
b. Reading the LED Battery Indicators
- Normal: Green
- Warning: Flashing Red
With new alkaline or freshly charged nicads the Green light should be brightly lit; as the green light starts
to fade the Red will begin to illuminate and eventually light completely as the green light goes out. Once
this occurs, operation should be stopped immediately, and the batteries should be recharged or replaced.
(Warning: Recharge Nicds batteries only. Alkaline batteries can not be recharged)
Alkaline or Nicad "AA"size
GREEN HIGH
LOW
HIGH
LOW
NORMAL WARNING
CG-22A or
CG-25A
(Not included)
RED
GREEN
RED
#7401 RX Nicad Battery
(Not included)
c. Recharging Nicd Batteries
The Lynx Sport is equipped with an external-charging jack so there is no need to remove the batteries from
the transmitter to charge them. The Hitec CG-22 or CG-25A charger can be used to charge the batteries
overnight, or for approximately 12~15 hours.
d. Transmitter Antenna
Always make sure your antenna is attached and fully extended before use otherwise your operating range
will be greatly reduced and could result in damage to your vehicle and or injuries to yourself and others.
e. Changing Crystals
Changing crystals to avoid conflicts with other vehicles is possible where permitted. (You must check your local
rules before doing so. For example in the US the FCC prohibits the changing of transmitter crystals on 75MHz).
If you are eligible to change crystals, both the transmitter and receiver crystals must be changed together.
You must change within the same band; i.e. 75MHz to 75MHz, 27MHz to 27MHz, different bands can not be
intermixed, if your radio is on 75MHz then 27MHz crystals cannot be used. Use only Hitec crystals when
changing frequencies.
Produktspezifikationen
| Marke: | Hitec |
| Kategorie: | Funksteuerung |
| Modell: | LINX_SPORT |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Hitec LINX_SPORT benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Funksteuerung Hitec
3 Mai 2023
3 Mai 2023
3 Mai 2023
3 Mai 2023
3 Mai 2023
3 Mai 2023
3 Mai 2023
3 Mai 2023
3 Mai 2023
3 Mai 2023
Bedienungsanleitung Funksteuerung
- Funksteuerung Reely
- Funksteuerung Absima
- Funksteuerung Saturn
- Funksteuerung Futaba
- Funksteuerung Graupner
- Funksteuerung JRpropo
- Funksteuerung Multiplex
- Funksteuerung Robbe
- Funksteuerung Robbe Futaba
- Funksteuerung Rush
- Funksteuerung Sanwa
- Funksteuerung Airtronics
Neueste Bedienungsanleitung für -Kategorien-
14 Oktober 2024
26 August 2024
26 August 2024
26 August 2024
26 August 2024
26 August 2024
26 August 2024
25 August 2024
25 August 2024
25 August 2024