BeamZ ICE1800 160.518 Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für BeamZ ICE1800 160.518 (12 Seiten) in der Kategorie Wir. Dieser Bedienungsanleitung war für 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/12
Ref. Nr. 160.518
ICE FOGGER
ICE 1800
INSTRUCTION MANUAL
GEBRUIKSAANWIJZING
BEDIENUNGSANLEITUNG
V1.1
- 2 -
Warning:
- The smokemachine must be placed at least 100 cm away from inflammable materials such as curtains,
books, etc. Make sure that the housing cannot be touched by accident.
- Use only Beamz water-based smoke fluid recommended by your dealer.
- Poor smoke liquid caused permanent damage, bad effect, clogging, spitting of unevaporated liquid etc.
- Never add flammable fluids (oil, gas, perfume) to the fog liquid.
- Always keep enough smoke liquid in the tank.
Use of the device without liquid will cause damage to the pump and heater.
- Do not obstruct the openings on top of the case to guarantee a good ventilation.
- Don’t put any objects on the smoke machine.
- For indoor use only.
- During installation, nobody should stand beneath the mounting area.
- Prior to the first use, have the unit checked by a qualified person.
- The unit contains voltage carrying parts. DO NOT open the smokemachine
- Never plug or unplug the unit with wet hands.
- If the plug and/or mains lead are damaged, they need to be repaired by a qualified technician.
- If the unit is damaged to an extent that you can see internal parts, do not plug the unit into a mains outlet. It
needs to be repaired by a qualified technician.
- Only connect this unit to an earthed mains outlet of 220- Vac/50Hz . 240
- Always unplug the unit during a thunderstorm or when it is not in use.
- If the unit has not been used for a longer period of time, condensation can occur inside the housing. Please
let the unit reach room temperature prior to use.
- When you unplug the unit from the mains always pull the plug, never the lead.
- In order to prevent dropping of the unit, a safety fastening needs to be installed. This can be a solid chain, a
steel cable, etc. which has to be fastened separately from the mounting bracket.
- The supplied bracket is the main fixing and must be used to solidly mount the light effect.
- In order to avoid accidents in public premises, the local legal requirements and safety regulations/warnings
must be fulfilled.
- Keep out of the reach of children.
Location
Select a location where it is easy to fill the tank. It is also possible to hang the unit by means of the supplied
holder and fixing screws.
Installation and Use
Unpack the fog machine. Do not connect yet the net cable. Connect the remote control to the connector on the
back of the fogger. Fill the fluid tank by means of a funnel. Fill the ice tray with ordinary ice. Close the drain
valve off. (Once ice has melted, you can drain the water here.) When the machine is filled with ice, the lid can
be closed.
Attention:Drain the water, melted ice regularly. (approximately every 45 minutes)
Plug the unit into a mains outlet. Thus the heating element is automatically switched on. Depending on the room
temperature, it takes about 8 minutes until the working temperature is reached. Then the thermostat is clicking
and the LED on the manual control lights up. Push the switch once and the smoke machine will produce a nice
thick fog. Once the smoke machine has reached its working temperature (the LED is lit) the smoke machine can
produce fog for a while. After this period of time, the fog generator is cooled so much down that the thermostat
switches off. Wait a while until the working temperature is reached again. It is recommended to produce smoke
with small pauses in between so that the temperature is maintained and th e thermostat doesn’t switch off.
Make sure that there is always enough liquid smoke contained in the tank. Use of the smoke machine without
liquid can permanently damage the unit. Once the smoke machine generates little smoke or pump generate
another 'rattling' sound i turn off the unit direct. Check the fluid level and fill the tank when it is empty, check the
hose and filter blockages and restore it. Plug in the unit and check if the problem is resolved. If problem persists,
switch unit direct off to prevent further damage and contact your dealer.
Switching the unit off
Switch the unit off by unplugging it from the mains. Otherwise the 1800W heating element will draw
unnecessarily current.
- 3 -
Timer remote control
Connect the remote control to the connector on the back of the fogger.
After some warm-up time, the device is ready for use, the LED will light up on the remote. During use, it may
happen that the machine stops, in this case the LED will go out, indicating that the machine is warming up.
Timer function:
Press the yellow button and set the interval, duration and volume controls to the desired level.
Interval: time between the smoke moments (10-200 seconds)
Volume: amount of smoke (0-100%)
Duration: duration of the smoking time
Continuous function:
Press the red button and set the volume to the desired level. The machine will continueously produce an
amount of smoke. It may be that the machine in between have to warm up, during this period no smoke is
produced. How many times this is done depends on the amount of smoke.
Manual Mode:
Press the green button to produce 100% smoke immediately; this button overrides all previous settings.
DMX control
Connect the device directly to a DMX controller or a DMX loop with multiple DMX effects. The machine has a 3-
pin XLR connector for DMX connection.
The machine needs 1 DMX channel to function:
Address Setup:
Use the DIP switch on the rear panel to set the start address. The base/start address is defined as a first
channel, where responsive to the device. Check if no overlapping channels are used!
Switch dip 10 on to activate the addressing
Set the desired address with the remaining 9 dips
Example addressing:
Startadres
Dipswitch setting
1
0000000001
5
0010000001
33
0000010001
6
1010000001
25
0001100001
67
0100001001
8
1110000001
105
0001011001
Note:
It is necessary always lock a DMX loop with a 120 Ohm terminator for correct data
transmission.
CHANNEL
VALUE
FUNCTION
1
0 – 100%
Smoke level
Produktspezifikationen
| Marke: | BeamZ |
| Kategorie: | Wir |
| Modell: | ICE1800 160.518 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit BeamZ ICE1800 160.518 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Wir BeamZ
31 Juli 2024
29 Juli 2024
25 Juli 2024
24 Juli 2024
16 Juli 2024
9 Juli 2024
8 Juli 2024
Bedienungsanleitung Wir
- Wir Crivit
- Wir Clatronic
- Wir G3 Ferrari
- Wir Ernesto
- Wir Tristar
- Wir Hama
- Wir Sunbeam
- Wir Bestron
- Wir Gastroback
- Wir Russell Hobbs
- Wir Steba
- Wir Tefal
- Wir IKEA
- Wir Black And Decker
- Wir Ryobi
- Wir Cuisinart
- Wir Fritel
- Wir Graef
- Wir Kenwood
- Wir Krups
- Wir Moulinex
- Wir Waring Commercial
- Wir Exquisit
- Wir Bartscher
- Wir Continental Edison
- Wir Livoo
- Wir Hazet
- Wir Kalorik
- Wir Team
- Wir Toolcraft
- Wir Wolf
- Wir Victorinox
- Wir HQ Power
- Wir Swan
- Wir Hamilton Beach
- Wir Oster
- Wir Girmi
- Wir Nutrichef
- Wir Underwater Kinetics
Neueste Bedienungsanleitung für -Kategorien-
3 Oktober 2024
30 September 2024
29 September 2024
24 September 2024
12 September 2024
7 September 2024
7 September 2024
7 September 2024
5 September 2024
4 September 2024