Vemer Energy-230 LC Bedienungsanleitung

Vemer Messgeräte Energy-230 LC

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Vemer Energy-230 LC (1 Seiten) in der Kategorie Messgeräte. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/1
User Manual
SINGLE-PHASE ACTIVE ENERGY METER
Read all the instructions carefully
V3IS00417-010-082010
Mod. Energy-230 LC
The Energy-230 LC static energy meter is an appliance to read active energy in single-phase
230V systems. It is designed to operate in environments with measurement category III and
pollution level 2 according to EN 61010-1 standard.
SAFETY WARNINGS
To guarantee correct installation, proceed as follows:
1) The appliance should be installed by a qualified operator
2) The appliance should be installed in a panel in such a way as to guarantee that the
terminals are inaccessible after fitting
3) A protection device against over-currents should be installed in the electrical system,
upstream of the energy meter
4) Connect the instrument as shown in the alongside diagrams
5) Before touching the connector terminals make sure that the wires to be connected or
already connected to the instrument are not live
6) Do not power or connect the instrument if any part of it is damaged
8) The instrument must be installed and activated in compliance with current electric
systems standards.
Code Model Description
VN960100 Energy-230 LC Single-phase active energy meter
TECHNICAL SPECIFICATIONS
Power supply: 230 V CA (-15%/+10%), 50/60 Hz
Maximum power consumption: 4 VA
Basic current: I = 15Ab
Maximum current: I MAX = 22,5 A
Starting current: ) 50 mA
Current circuit consumption: < 2 VA
Operating temperature: -10 ÷ +45 °C
Storage temperature: -20 ÷ +60 °C
Relative humidity: 10% ÷ 90% non-condensing
Connection type: direct for current conductors
Signaling leds: green = power on
red = flashing at 10Wh
Accuracy: class 2 (EN 62053-21)
Display: 6-digit mechanical counter
Reading resolution: 0,1 kWh (full scale: 99999,9 kWh)
Housing: 2 DIN, gray RAL 7035
Protection degree: IP20/IP51 on the front
OPERATION
In normal operation, the led is on and red led flashes in proportion to the green the
active power (flashing at 10Wh).
The meter counts the consumption of active power with a resolution of 0,1 kWh.
PHASE ERROR
When the energy meter is turned on, a connection check-up is automatically carried out
to detect any connection errors: in case of improper connection, the and leds red green
flash alternate and the meter is locked.
Warning: to restore correct meter operation after an error reading has been
showed, switch the meter off, invert connections of voltage or current
and turn on again.
REFERENCE STANDARS
Conformity to EU directives:
2006/95/EC (Low Voltage)
2004/108/EC (EMC)
is declared with reference to the following harmonised standards:
EN 61010-1 EN 62053-21and
Dimensions
Connection
Description
(OHFWULFDOORDG
0D[$
9$&+]
 

7HUPLQDOEORFNIRUGLUHFW
FRQQHFWLRQRIPHWHULQJZLUHV
7RWDOHQHUJ\
*UHHQOHG
OLW SRZHURQ
5HGOHG
IODVK :K
Energy-230
kWh
15(22.5)A cl.2
230V~ 50/60Hz
ON 10Wh/imp
,
4
16000


Produktspezifikationen

Marke: Vemer
Kategorie: Messgeräte
Modell: Energy-230 LC

Brauchst du Hilfe?

Wenn Sie Hilfe mit Vemer Energy-230 LC benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Messgeräte Vemer

Bedienungsanleitung Messgeräte

Neueste Bedienungsanleitung für -Kategorien-