Ultimate Speed IAN 280326 Bedienungsanleitung

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Ultimate Speed IAN 280326 (11 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 17 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/11
IAN 280326
CAR SEAT COVER SET
IAN 280326
Walser GmbH
Radetzkystraße 114
A-6845 Hohenems
Email: office@walsergroup.com
www.walsergroup.com
Last Information Update · Inforciók állása
Stanje informacij · Stav informací · Stav inforcií
Stand der Informationen: 09 / 2016
Ident.-No.: 280326092016-1
4
DE
HU
CZ
SI
SK
GB
AT CH
AUTOSITZBEZUG-SET
Montage- und Sicherheitshinweise
AUTÓS ÜLÉSHUZAT
Szerelési- és biztonsági utasítások
SADA AUTOPOTAHŮ
Pokyny k montáži a bezpečnostní pokyny
KOMPLET PREVLEK ZA
AVTOMOBILSKE SEDEŽE
Navodila za montažo in varnost
AUTOPOŤAHY
Pokyny pre montáž a bezpečnosť
CAR SEAT COVER SET
Assembly and safety advice
CZ SK
HU SI
GB
SI
CZ
SK
DE AT CH
HU
GB Assembly and safety advice Page 5
HU Szerelési- és biztonsági utasítások Oldal 6
SI Navodila za montažo in varnost Stran 7
CZ Pokyny k montáži a bezpečnostní pokyny Strana 8
SK Pokyny pre montáž a bezpečnosť Strana 9
DE/AT/CH Montage- und Sicherheitshinweise Seite 10
Before reading, unfold both pages containing illustrations and familiarise yourself with all functions of the
product.
Pred branjem odprite obe strani s slikami in se nato seznanite z vsemi funkcijami izdelka.
Před čtením si otevřete obě strany s obrázky a potom se seznamte se všemi funkcemi výrobku.
Pred čítaním si otvorte obidve strany s obrázkami a následne sa oboznámte so všetkými funkciami výrobku.
Klappen Sie vor dem Lesen die beiden Seiten mit den Abbildungen aus und machen Sie sich anschließend
mit allen Funktionen des Produkts vertraut.
Az elolvasás előtt nyissa fel az ábrákat tartalmazó mindkét oldalt és végezetül ismerje meg a terk
mindegyik funkcióját.
SI
DE
CZ
SK
HU
AT CH
Obseg dobave
2 x prevleka za sprednje sedeže (v 1 ali 2 delih, odvisno od izvedbe izdelka)
2–5 x prevlek za naslonjalo za glavo (odvisno od izvedbe izdelka)
1 x prevleka za naslonjalo zadnjega sedeža (v 1 do 5 delov, odvisno od izvedbe izdelka)
1 x prevleka zadnje sedežne površine (ni deljiva
Kovinski kavelj (nahaja se v prevlekah za naslonjala za glavo)
Seznam tipov
Lieferumfang
2 x Bezüge Vordersitze (in 1 oder 2 Teilen, je nach Artikelausführung)
2–5 x Bezüge Kopfstützen (je nach Artikelausführung)
1 x Bezug Rücksitz-Lehne (in 1 bis 5 Teilen, je nach Artikelausführung)
1 x Bezug Rücksitz- Sitzfläche (nicht teilbar)
Metallhaken (Befinden sich in den Kopfstützenbezügen)
Typenliste
Rozsah dodávky
2 x potahy na přední sedadla (1dílné nebo 2dílné, podle provedení výrobku)
2–5 x potahů na hlavoopěrky (podle provedení výrobku)
1 x potah na opěradlo zadního sedadla (1dílný a 5dílný, podle provedení výrobku)
1 x potah na sedák zadního sedadla (nedělitelný)
Kovové háky (nacházejí se v potazích na hlavové opěrky)
Seznam typů
Rozsah dodávky
2 x poťahy predných sedadiel (vyhotovené ako 1 alebo 2 diely, podľa vyhotovenia výrobku)
2–5 x poťahov hlavoch opierok (podľa vyhotovenia výrobku)
1 x poťah zadného operadla (vyhotovené ako 1 až 5 dielov, podľa vyhotovenia výrobku)
1 x poťah sedacej plochy zadných sedadiel (nie je možné rozdeliť)
kovové háčiky (nachádzajú sa v poťahoch hlavových opierok)
Zoznam typov
A csomagolás tartalma
2 x elülső üléshuzat (1 vagy 2 részes, a kiviteltől függően)
2-5 x fejtámla huzat (a kiviteltől függően)
1 x hátsó ülőfelület huzat (nem osztható)
1 x hátsó ülésháttámla huzat (1-5 részes, a kiviteltől függően)
fémkampók (a fejtámla huzatokban találhatóak)
Típuslista
GB
Scope of delivery
2 x covers for front seats (in 1 or 2 parts according to design)
2 - 5 x covers for headrests (according to design)
1 x cover for rear backrest (in 1 to 5 parts according to design)
1 x cover for back seat (not separable)
Metal hooks (located in the headrest covers)
List of types
2 3 4
5 6 7 8
9 10 11 12
13 14 15 16
17 18 19 20
21 23 24
1
22
25 26 27
28 29 30
31 32 33 34
35 36 37
38 39 40
43 44 45
41
42
GB 5
Car seat cover set
• Introduction
We congratulate you on your purchase. You have chosen a high quality product.
The instructions for use are to be considered as part of this product. Before using the
product, please familiarise yourself with all the safety information and instructions
for use. Only use the product as instructed and only for the stated areas of use. If you pass the
product on to anyone else, please ensure that you also pass on all the documentation with it.
• Intended use
Set of car seat covers for the driver‘s seat, passenger‘s seat and the back seats of cars
(according to the enclosed type list).
• Safety instructions
Correct installation res. fastening of the seat covers to the vehicle is essential to guarantee the sa-
fety of the user. Please pay attention to the following information when installing the seat covers:
WARNING! DANGER OF SUFFOCATION! Keep the pa-
ckaging out of reach of small children.
Installation is permissible only in cars that are indicated in the list of types on the pa-
ckaging or in the enclosed, detailed list of types.
Correct assignment of the seat (driver and front passenger seat). The covers are assig-
ned by the marking „airbag“ attached to the seat cover. This marking must be attached
to the outer side of the backrest (see fig. 1.0).
Headrest inserts, adjustment levers / wheels for release of backrests or armrests may
not be covered with the seat cover. Allowances must be made for appropriate inserts.
Please observe the instructions given in section “Installation”.
Displaced seat covers must be repositioned. If this is no longer possible due to a advan-
ced state of wear and tear, the cover must be removed or replaced.
Manipulation of the opening of the seat covers is not permissible (no covering, sewing
up or repairs by yourself).
This protective cover has been tested by TÜV Rhineland Group.
CAUTION! If the seat covers are installed incorrectly, the proper extension and infla-
tion of the seat air bag cannot be guaranteed in the case of a collision.
• Installation of seat covers
You need a pair of pointed scissors.
Important: Please read the information below before installing the seat covers!
Fig. 1: Remove headrests (in some car models the headrests must be dismantled in
a garage).
Fig. 2: Cover the backrest by pulling the cover downwards.
Fig. 3: Pay attention to the correct assignment of the side airbag label (right / left
seat)! The side airbag label must be located at the outside (door side) of the
respective seat.
Fig. 4: Pull the strap through between the seat and the backrest.
Fig. 5: Then close the fastener.
Fig. 6: Cover the seat from the front to the back.
Fig. 7: Fasten the metal hooks to the rubber loops.
Fig. 8+9: Pull the rear rubber loops between the seat and backrest (as you did with the
strap of the backrest cover). Fasten the metal hooks under the seat according
to the car model (e.g. to the existing metal rods - ATTENTION Do not fasten
to airbag cables!)
Fig. 10: Or fasten all rubber loops together.
ATTENTION!
Openings for backrest releases, adjustment levers, side levers etc. (as described under fig.
11–21) must be cut out.
If your seat is equipped with armrests, proceed as described under g.
11. Otherwise go to fig. 15.
Fig. 11: Pull the cover down as far as the armrest. The cover must be tightly fitting on top.
Fig 12: Cut the cover in the position of the armrest. The cut-out may not be too large.
Fig. 13: Push up the armrest and pull it through the cut-out opening of the cover.
Fig. 14: Pull the strap through between the seat and the backrest and close with the fastener.
If your seat is equipped with side levers, proceed as described under fig.
15. Otherwise go to fig. 19.
Fig. 15: Cover the seat as described under section 2. The cover must be tightly
fitting on top.
Fig. 16: Cut the cover in the position of the side lever. The cut-out may
not be too large.
Fig. 17+18: With the aid of scissors, push the cover under the guide fitting.
If your seat is equipped with seat frame cladding, proceed as described
under fig. 19. Otherwise go to fig. 22.
Fig. 19: (for Renault) Open the seat frame cladding under the seat.
Fig. 20: (for Mercedes) Open the seat frame cladding under the seat.
Fig. 21: Fold the seat frame cladding under the seat cover. Pull the strap through
between the seat and the backrest. Then close the fastener at the back.
Fig. 22: Cover the headrests.
Fig. 23+24: Position the mounting strip directly above the holes for insertion of the headrest.
Cut open the mounting strip in the exact positions of the headrest holes. With
the aid of the integrated mounting strip, it is not possible for the material to tear.
Fig. 25+26: Push the cover beneath the plastic of the headrest guide covering. In a
few isolated car models, it could be the case that these models have no
headrest guide covering.
Fig. 27+28: Pull the cover for the back seat towards the back of the seat. If necessary,
tilt the back seat forward and fasten the rubber loops at the back to the
metal hooks (according to the car model).
Fig. 29: Position the cover exactly in the location of the seat belt.
Fig. 30: Carefully cut the cover in the position of the seat belt.
Fig. 31: Push the cover under the seat belt holder.
Fig. 32: Pull the cover under the backrest. The cover must be under the seat belt!
Fig. 33: Cut the cover in the position of the belt guide.
Fig. 34+35: Push the cover beneath the plastic of the belt guide.
Fig. 36: The backrest cover is universally suitable for all back seats due to the triple zip faste-
ner division. The zip-in part can be used according to the width of the rear backrest.
Fig. 37: Fasten the rubber loops at the back to the metal hooks.
If your your back seat is equipped with armrests, proceed as described
under fig. 38. Otherwise go to fig. 40.
Fig. 38: Open the zip fasteners. Fold out the armrest. Close the zip fastener up to
the armrest.
Fig. 39: Complete covered armrest.
Fig. 40: In case of divided back seats, open the variable zip fasteners with the
slider facing upwards if necessary.
Fig. 41: Remove the rear headrests.
Fig. 42: Cover the rear headrests.
Fig. 43: Cut the backrest cover in the position of the headrest in an x-shaped form.
Fig. 44+45: Push the cover under the plastic.
• Instructions for care and disposal
Wash the covers by hand Do not iron
Do not use bleach Do not dry clean
Do not dry in a tumbler
The seat covers can be disposed of in the household waste.
Please dispose of the packaging in accordance with the local regulations.
• Service & guarantee
This product has been produced with great care and under continuous quality control. The
product comes with a three year guarantee from date of purchase. Please keep your receipt
safe. The guarantee applies only to material and manufacturing defects and does not ap-
ply to misuse or improper treatment. Your statutory rights, especially the rights of warranty,
are not restricted by this guarantee.
Extent of validity: Please use the service hotline which has been provided for you or contact
the service centre in the European Economic Area.
Costs: Repair or replacement free of charge or a refund of the purchase cost. Shipping
costs will not be charged.
Advisory notice: Before returning your product, contact our hotline by telephone, so
that we can help you with any operating errors.
Service address: Return address:
Walser Industrie- und Handels GmbH Walser Customer Service Germany
Langenweg 34 Walser GmbH
DE-88131 Lindau, Germany Bleicheweg 15, Postfach 3325
DE-88131 Lindau, Germany
Telephone number of Service-Hotline: 00800 00300030
www.walsergroup.com / clix
IAN 280326
Fig. 1.0

Produktspezifikationen

Marke: Ultimate Speed
Kategorie: Nicht kategorisiert
Modell: IAN 280326

Brauchst du Hilfe?

Wenn Sie Hilfe mit Ultimate Speed IAN 280326 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Ultimate Speed

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-