Supermicro SuperServer 5018A-MHN4 Bedienungsanleitung

Supermicro Server SuperServer 5018A-MHN4

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Supermicro SuperServer 5018A-MHN4 (1 Seiten) in der Kategorie Server. Dieser Bedienungsanleitung war für 22 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/1

http://www.supermicro.com MNL-1579-QRG

Board Layout

SuperServer 5018A-MHN4 Quick Reference Guide

Beep Codes

Rear View MEMORY

Caution

SAFETY INFORMATION

IMPORTANT: See installation instructions and safety warning

before connecting system to power supply.

http://www.supermicro.com/about/policies/safety_information.cfm

WARNING:

To reduce risk of electric shock/damage to equipment,

disconnect power from server by disconnecting all power

cords from electrical outlets.

If any CPU socket empty, install protective plastic CPU cap

CAUTION:

Always be sure all power supplies for this system have

the same power output. If mixed power supplies are

installed, the system will not operate.

For more information go to :

http://www.supermicro.com/support



Descrip iot n

No.

Slot4 PCI-E 2.0 x4

Slot6 PCI-E 2.0 x8

JTPM1 = Trusted Platform Module (TPM)/Port 80 Connector

JSD1 = SATA DOM Power Connector

JBT1 = CMOS Clear

CPU1

DIMMB1(Blue)/DIMMB2

DIMMA1(Blue)/DIMMA2

I-SATA0 ~ I-SATA5 = SATA Ports 0~5

BIOS Error Beep Codes

Beep Code/LED Error Message Description

1 beep Refresh Circuits have been reset.

(Ready to power up)

5 short beeps + 1 long

beep

Memory error No memory detected in the

system

8 beeps Display memory

read/write error

htiw ro gnissim retpada oediV

faulty memory

OH LED On System OH System Overheat

Power Button

Reset Button

Power LED

Device Activity LED

LAN1 LED & LAN2 LED

Information LED

Hard Drive Signal

Hard Drive Fail

Description

No.

Description

No. 78

PCI-E Expansion Slot (w/riser card)

UID

VGA Port

GbE LAN1/2 Port

GbE LAN3/4 Port

USB 0/1/2/3 Ports

COM1 Port

Dedicated LAN for IPMI

Single/Redundant Power Supply Module

SATA Drive Installation

DIMMB2

DIMMB1

(Blu Sloe t)

DI A1MM

(Blu Sloe t)

DIMMA2

3456

9 12

The SATA drives are mounted in drive carriers

to simplify their installation and removal from the chassis.

These carriers also help promote proper airflow for the

system. For this reason, even empty carriers without

drives installed must remain in the chassis.

1. Install a new drive into the carrier with the printed

circuit baord side facing down so that the mounting

holes align with those in the carrier.

2. Secure the drive to the carrier with six screws,

as shown.

Mounting a Drive in a Drive Carrier

Installing/Removing SATA Drives

1. To remove a carrier, push the release button located beside the drive LEDs.

2. Swing the colored handle fully and use it to pull the unit straight out.

Unbuffered (UDIMM) DDR3 Memory

DIMM Slots per

Channel

DIMMs Populat-

ed per Channel

DIMM Type POR Speeds Memory Population

Sequence

2 1 Unbuffered

DDR3 DIMM

1600,1333 A1, B1 (2 DIMMs)

2 2 Unbuffered

DDR3 DIMM

1600,1333 A1, B1, A2, B2

(4 DIMMs)

Note: Use memory modules of the same type, speed, frequency and size.

123456

HDD 0 HDD 1 HDD 2 HDD 3

JPI2C1

JL1

JOH1

JF1

JPW1

JLAN2 JLAN1

JBT1

LED8

LED7

JPK1

SP1

JBAT1

JWD1JPB1

JI2C2

JI2C1

JPG1

JPL1

JSD1

JTPM1

JIPMB1

JVGA1

JUIDB1

COM2

JD1

I-SATA1 I-SATA0

I-SATA5

I-SATA4

I-SATA2

FAN3

FAN1

CPU1 SLOT4 PCI-E 2.0 X4

USB6

LAN3/4 LED

LAN2/LAN4

DIMMB2

DIMMA2

USB0/1

BUZZER

IPMI_LAN

BATTERY

DIMMB1

CPU1 SLOT6 PCI-E 2.0 X8

LAN1/LAN3

DIMMA1

USB4/5

COM1

A1SAM/A1SRM Series

USB 2/3

FPCTRL LED3

BIO

SoC Processor

BMC

PHY

JBR1

JPUSB1

JSTBY1

PWRI2C

1 2 3 6 7 8

4 5



CAUTION:

The fans on the A1SRM-2758F are not hot-swappable.

Front View & Interface

ÌMNL-1579-QRGOÎ

Produktspezifikationen

Marke:	Supermicro
Kategorie:	Server
Modell:	SuperServer 5018A-MHN4
Breite:	437 mm
Tiefe:	503 mm
Gewicht:	3620 g
Produktfarbe:	Silber
Höhe:	43 mm
Anzahl USB 2.0 Anschlüsse:	7
Betriebstemperatur:	10 - 35 °C
Relative Luftfeuchtigkeit in Betrieb:	8 - 90 %
Anzahl Ethernet-LAN-Anschlüsse (RJ-45):	3
Warentarifnummer (HS):	84714100
Ethernet LAN Datentransferraten:	10,100,1000 Mbit/s
Stromversorgung:	200 W
LED-Anzeigen:	Ja
Temperaturbereich bei Lagerung:	-40 - 70 °C
Luftfeuchtigkeit bei Lagerung:	5 - 95 %
Kupfer Ethernet Verkabelungstechnologie:	1000BASE-T, 100BASE-TX, 10BASE-T
Ein-/Ausschalter:	Ja
Prozessorfamilie:	Intel
Anzahl der unterstützten Speicherlaufwerke:	4
Gehäusetyp:	Rack (1U)
Prozessorsockel:	BGA 1283
Anzahl VGA (D-Sub) Anschlüsse:	1
Kompatible Prozessoren:	Intel Atom®
Unterstützte Arbeitsspeicher:	DDR3-SDRAM
ECC:	Ja
Ohne ECC:	Ja
Unterstützte Speicherlaufwerk-Schnittstellen:	Serial ATA II
SATA III Anschlüsse:	2
BIOS-Speichergröße:	128 Mbit
BIOS-Typ:	AMI
ACPI-Version:	5.0
Ethernet Schnittstellen Typ:	Fast Ethernet, Gigabit Ethernet
Anzahl serielle Anschlüsse:	2
On-Board Grafikadaptermodell:	Aspeed AST2400
SATA II Anschlüsse:	4
Memory Formfaktor:	240-pin DIMM
Speicherspannung:	1.35, 1.5 V
Anzahl unterstützter Prozessoren:	1
PCI-Express x8-Slots:	1
Zahl der DIMM Slots:	4
Unterstützte RDIMM Taktraten:	1333,1600 MHz
unterstützte Speicherlaufwerksgrößen:	3.5 "
HDD Laufwerkschächte Hot-Swap:	Ja
IPMI LAN (RJ-45)-Anschluss:	Ja
Unterstützte DIMM-Modulkapazitäten:	16GB, 2GB, 4GB, 8GB
BIOS-Funktionen:	UEFI
Ethernet/LAN:	Ja