Sani-Lav 5A2F Bedienungsanleitung
Sani-Lav
SpĂŒlbecken
5A2F
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂŒr Sani-Lav 5A2F (5 Seiten) in der Kategorie SpĂŒlbecken. Dieser Bedienungsanleitung war fĂŒr 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/5
1
W A L L M O U N T WA S H S TAT I O N
Operating Manual for 2-Person Wall Mount Stainless Steel Wash Station
Models 5A2F and 5A2F-0.5
of Domestic and Foreign Parts
Columbia does not recommend use with harsh chemicals.
Product Compliance
NSF/ANSI 2 Food Equipment, NSF/ANSI 61, Section 9, ASME A112.18.1/CSA B125.1, ADA Compliant
ADA Compliant
2
C O L U M B I A S P E C I F I C AT I O N S
800.626.2117 columbiasinks.com info@columbiasinks.com
©2021 Columbia Products
W A L L M O U N T WA S H S TAT I O N
Parts List
(1) Wall mount wash station
(2) 8â on center faucets
(2) Faucet mounting kit
(2) Wall-mounting brackets
(2) Support brackets
(4) Support bracket mounting bolts and washers
(1) Strainer assembly with basket
Installation Instructions
Step 1
1. Establish sink location on the wall.
2. Measure a recommended 45â from finished floor and draw a level line which will be the top edge
of the wall mounting bracket.
3. Hold the wall mounting bracket against the wall and mark the wall where the holes are. Drill holes
and secure bracket to the wall as shown in illustration A. Screws are not provided.
Step 2
1. Install faucet to the sink using faucet mounting kit provided. We recommend using pipe thread
sealant instead of Teflon tape.
2. Install strainer assembly to the drain hole.
3. Connect hot and cold water supply lines (not included) to the back of faucets.
Step 3
1. Position sink onto the wall bracket.
2. Mount support bracket to the bottom of the sink. Do not tighten.
3. Slide or push support brackets against the wall and mark holes for fastening. See illustration B.
4. Remove support brackets from the sink and drill holes for fastening.
5. Install fastening hardware to the drilled holes. (not included)
6. Mount support bracket to the bottom of the sink and fasten them to the wall.
Step 4
1. Install valves onto the sink.
2. Install elbow fittings to Knee Pedal Valves.
3. Connect hot and cold connecting tubes from the spouts to valves.
Step 5
1. Connect waste line or drain pipe to the strainer assembly.
2. Connect hot and cold water supply line to the water source.
Step 6
1. Remove aerator from the spout assembly and flush water system. Check connections for leaks.
Replace aerator onto the spout assembly.
2. We recommend sealing top of backsplash to wall as shown in illustration C.
Trouble Shooting Guide
Problem Possible Cause To Diagnose Remedy
Water drips from
the spout or from
under the lever.
1. Seat washer is worn
2. Seat is worn
3. O-rings are worn
Shut cold water source off. See if
water still leaks from the spout. If
leaks continues repair hot side if
not repair cold side.
Recommend
installing hot
or cold faucet
repair kit.
Tools Required
Tape measure
Adjustable wrench
Drill motor and drill bits
Pipe wrench
Level
Safety glasses
Screw drivers: phillips and standard
Pencil
Socket wrench
WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),
Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
NOTE: Lead content originates from Brass components in valves and faucets and is certiîed under
NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.
Notice for California Consumers
Go to for more information on replacement parts and installation videos.columbiasinks.com
Illustration A
Illustration B
Illustration C
3
C O L U M B I A S P E C I F I C AT I O N S
800.626.2117 columbiasinks.com info@columbiasinks.com
©2021 Columbia Products
W A L L M O U N T WA S H S TAT I O N
Wall-mounting brackets
10â (254mm)
10â (254mm)
45Âș
35â (889mm)
suggested
ïŹoor to rim
height
.437â (6mm)
.75â (19mm) slot
.437â (6mm)
dia. hole
Front Side
47.125â (1197mm)
20â (508mm)
2â (51mm)
1.5â (38mm)
7.5â (191mm)
.875â (22mm)
dia. holes (4)
Hole ConïŹgurations
6â
(152mm)
6â
(152mm)
8â
(203.2mm)
8â
(203.2mm)
20â
(508mm)
6â (152.4mm)
5â (127mm)
48â (1219mm)
24â (609mm) 24â (609mm)
20â
(508mm)
16.5â
(407mm)
7â (177.8mm)
1.5â (38mm)
2â (51mm)
1.5â (38mm)
Top
45â (1143mm)
6â (152.4mm)
16.75â (425.45 mm)
2â drain hole
(50.8mm)
.5â R
(12.7mm)
Cross-breaks to aid drainage
4â (101.6mm)
2â
(51mm) .875â
(22.22mm)
Back
Splash
.375â
dia. hole
Wall Mounting Detail
.5â R (12.7mm)
Back Splash
Supply Line Detail
1/2â Male NPT
Hot
from Wall
Cold
from Wall
Produktspezifikationen
| Marke: | Sani-Lav |
| Kategorie: | SpĂŒlbecken |
| Modell: | 5A2F |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Sani-Lav 5A2F benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung SpĂŒlbecken Sani-Lav
21 August 2024
6 Mai 2024
1 Mai 2024
1 April 2024
13 MĂ€rz 2024
11 MĂ€rz 2024
5 MĂ€rz 2024
18 Februar 2024
6 Februar 2024
28 Januar 2024
Bedienungsanleitung SpĂŒlbecken
- SpĂŒlbecken Concept
- SpĂŒlbecken Teka
- SpĂŒlbecken Smeg
- SpĂŒlbecken Caple
- SpĂŒlbecken Kernau
- SpĂŒlbecken Saro
- SpĂŒlbecken Foster
- SpĂŒlbecken Leisure
- SpĂŒlbecken Gustavsberg
- SpĂŒlbecken CDA
- SpĂŒlbecken Schock
- SpĂŒlbecken Rangemaster
- SpĂŒlbecken BLANCO
- SpĂŒlbecken Elkay
- SpĂŒlbecken Deante
- SpĂŒlbecken Roca
- SpĂŒlbecken Artusi
- SpĂŒlbecken Advance Tabco
- SpĂŒlbecken Cookology
- SpĂŒlbecken Tot Mate
- SpĂŒlbecken Eagle Group
- SpĂŒlbecken Kuchinox
- SpĂŒlbecken Oliveri
Neueste Bedienungsanleitung fĂŒr -Kategorien-
18 August 2024
17 August 2024
10 August 2024
21 Juni 2024
21 Juni 2024
21 Juni 2024
13 Juni 2024
13 Juni 2024
13 Juni 2024
13 Juni 2024