Oliveri ST-BL1584U Bedienungsanleitung

Oliveri SpĆ¼lbecken ST-BL1584U

Lesen Sie kostenlos die šŸ“– deutsche Bedienungsanleitung fĆ¼r Oliveri ST-BL1584U (4 Seiten) in der Kategorie SpĆ¼lbecken. Dieser Bedienungsanleitung war fĆ¼r 4 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
The latest technological advances are used in the
manufacturing process of our sinks which are tested a
number of times during the production process to ensure
they comply with rigorous quality standards.
Manufactured from 80% granite and 20% quartz and
resin, the sink is scratch, heat and stain resistant.
This sink can be installed on virtually any type of
benchtop, including wood, plastic, marble, etc.
Correct and proper use of your sink will ensure its
long-lasting life. Consult the Care and Maintenance
section of this manual for advice on cleaning and
regular maintenance.
PLEASE NOTE
If a washing machine or dishwasher is going to be
installed beneath the sink, proceed as follows:
ā€¢ To prevent overheating, which may result in the
deformation of the sink, adjust the feet on the washing
machine / dishwasher so there is sufļ¬cient ventilation
between the appliance and the sink.
ā€¢ To facilitate air circulation and cooling, we recommend
providing the cabinet base with ventilation slots.
oliveri.com.au
Installation Instructions
Santorini
ST-BL1584U
Farmhouse Undermount Sink
THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED TRADESPERSON
TF29a ā€“ ST-BL1584U Installation Instructions / June 2021 / Page 1 of 4
PRE-INSTALLATION CHECKS
Unpack & check the item is correct and no
damage has occurred during transit.
If there are any visible defects, DO NOT
PROCEED WITH THE INSTALLATION and
please contact the place of purchase
immediately.
ANY CLAIMS FOR DAMAGE WILL NOT BE
ACCEPTED AFTER INSTALLATION.
Protect your sink before and during
installation. Scratches, cracks or other
surface damage sustained during or after
the installation are NOT COVERED BY
WARRANTY.
Installation must be in accordance with
building regulations and any local
authority requirements.
CAUTION: Composite Sinks are HEAVY, be
sure to get help when lifting or moving.
STOP AND READ CAREFULLY
We recommend that only professional and expert installers
carry out the installation. As a bespoke artisan installation is
required, no cut-out pattern is provided.
We strongly recommend that you provide your installer with the
actual sink before the manufacture or modiļ¬cation of a cabinet. To
modify a standard cabinet so that it can accommodate and support
the weight of the farmhouse sink, a reinforcement must be built
inside it, by inserting a reinforced support surface.
When the sink is positioned on the support sructure, make sure that
the top of the sink reaches the bottom of the benchtop.
ATTENTION: check that the support structure is suitable for
this type of sink as its weight, including that of the water
it could contain, could exceed 70 kg. Reinforce the support
structure if needed. Minimum cabinet width 900mm.
The Farmhouse Sink is for UNDERMOUNT ONLY.
Step 1 Prepare the Sink Cabinet
To support the weight of the sink, prepare an internal support shelf
or a support structure.
Drill the drain hole on the support shelf (A), taking into account the
presence of the basket waste ļ¬tting. Prepare a hole in the rear area
for the water supply pipes (B).
Fit the strainer into the hole from the top,
and then place the drain under the hole.
Risk of personal injury. Composite sinks are heavy. Get help when lifting
or moving. Be sure to use proper tools and always wear personal safety
devices for your protection.
CAUTION
The internal support
shelf must be installed
at the preset height.
See Step 3
B
A
Basket
Screw
Strainer
Seal
Drain
1
2
3
4
5
INSTALLATION STEPS
SINK ASSEMBLY
Fasten the strainer to the drain using the
screw provided. Do not overtighten.
Tools needed for installation
Drain Parts
You MUST check the sink is NOT DAMAGED
before proceeding with installation.
Page 2 of 4
Step 2 Cut out the Cabinet Front
Cut the front of the cabinet using the dimensions shown below.
NOTE
Measurement ā€œCā€ must be greater than the height of the sink.
(240mm).
Step 3 Cut and Install the Benchtop
Reversible Fronts The Farmhouse Sink has the peculiarity of having
two different fronts: one front has ā€˜sharpā€™ corners, with a radius of
18mm and a 32mm top edge to suit the style of modern and
contemporary environments. The opposite front has more rounded
corners with a 40mm radius, and a wider top edge of 40mm. These
softer lines are the ideal combination for country kitchens, or those
kitchens with a more classic or retro design.
Before cutting the benchtop opening, choose
the direction the sink will face.
The following diagrams show the measurements to be used to cut
the benchtop hole, according to the direction chosen.
Step 4 Seal the Sink with the Benchtop
Apply a thin bead of only ā€˜neutral cureā€™ silicone sealant where the sink
meets the benchtop and cabinet. Use of an ā€˜acetic cureā€™ silicone can
irreparably damage the sink. Immediately wipe away excess sealant.
NB: Cut dimensions are intended for standard depth benchtops (648mm).
INSTALL WITH 32mm FRONT EDGE (SHARP)
767mm
520mm
52mm
143.5mm
407mm
187mm
CABINET 610mm
461mm
240mm
R20mm
40mm 32mm
767mm
520mm
61mm
151mm
407mm
187mm
CABINET 610mm
461mm
R20mm
240mm
INSTALLATION STEPS
INSTALL WITH 40mm FRONT EDGE (ROUND)
C
822mm
240mm
838mm
The front of the cabinet needs to be
cut-out allowing the sink to protrude.
Page 3 of 4


Produktspezifikationen

Marke: Oliveri
Kategorie: SpĆ¼lbecken
Modell: ST-BL1584U

Brauchst du Hilfe?

Wenn Sie Hilfe mit Oliveri ST-BL1584U benƶtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten