Projecta VSR100 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Projecta VSR100 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 22 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
FEATURES
Projecta’s Voltage Sensitive Relays (VSRs) are suitable for
a wide variety of 12V DC applications.
VSRs sense the input voltage and automatically connect/
disconnect the appliance or circuit at the set voltages.
The cut-out has an 8 sec. delay preventing the relay from
disconnecting during a momentary drop in voltage.
Manual override
Manual override is activated by connecting the override
wire to 12V DC. This bypasses the automatic voltage sensor
allowing the relay to be engaged below the set voltages.
Surge protected
Weatherproof (IP66)
L.E.D Indicator (on/contact closed)
WARNING
• PLEASE READ THESE INSTRUCTIONS COMPLETELY
PRIOR TO INSTALLATION.
• BATTERIES PRODUCE EXPLOSIVE GASES –
Ensure no sparks or flames are present.
• Wear eye protection.
• Vehicles must be in ‘NEUTRAL’ or ‘PARK’,
park brakes ‘ON’.
• Follow all vehicle manufacturer’s instructions.
• Beware of moving parts.
• Voltage Sensitive Relays (VSR) are designed for negative
ground alternator systems with batteries of the same
nominal voltage.
• Batteries of differing voltages cannot be used.
SPECIFICATIONS
P/No. VSR100 VSR200
VOLTAGE 12V 12V
CHARGING CURRENT 100A Continuous, 200A Peak 200A Continuous, 400A Peak
CUT-IN VOLTAGE 13.4V 13.4V
CUT-OUT VOLTAGE 12.8V 12.8V
CUT-OUT DELAY 8 sec. 8 sec.
CHARGE TYPE Parallel Parallel
CONTROL MCU MCU
MOUNTING Surface/Firewall Surface/Firewall
CURRENT DRAW Charging 550mA (standby 10mA) Charging 680mA (standby 10mA)
VOLTAGE DROP Nil Nil
SURGE PROTECTION Built-in Built-in
ENVIRONMENTAL PROTECTION IP66 IP66
OVERRIDE Requires minimum 10V Requires minimum 10V
RECOMMENDED FUSE 150A 250A
MINIMUM CABLE SIZE 14mm2(6 B&S) 32mm2(2 B&S)
TORQUE SETTINGS 3.75Lb/ft, 5Nm 3.75Lb/ft, 5Nm
Distributed by AUSTRALIA
Brown & Watson International Pty Ltd
Knoxfield, Victoria 3180
Telephone (03) 9730 6000
Facsimile (03) 9730 6050
National Toll Free 1800 113 443
NEW ZEALAND
Narva New Zealand Ltd
22–24 Olive Road
PO Box 12556 Penrose
Auckland, New Zealand
Telephone (09) 525 4575
Facsimile (09) 579 1192
IS115
Issue 2: 19.7.10
12 VOLT
USER MANUAL
VOLTAGE SENSITIVE RELAY
P/No.s VSR100, VSR200
INSTALLATION
1. Disconnect the negative battery cable (Earth) from the starting battery.
Note: To prevent the loss of the vehicle’s electronic memory, preset radio and security codes it is recommended that
an ‘Electrical System Memory Protector’ (P/No. IPS700) be used.
2. Mount the VSR in a convenient location. Mount as far away as possible form the exhaust manifold, turbo or any other
high temperature components. Do not mount on the engine.
3. Connect the VSR ’MAIN’ (+) terminal to the starting battery.
Note: For safety reasons it is recommended to install a fuse close to the starting battery.
4. Connect the VSR ‘AUX’ (+) terminal to the auxiliary load or battery.
Note: If connected to an auxiliary battery, it is recommended for safety reasons to install a fuse close to the auxiliary battery.
5. Connect the VSR ‘EARTH’ (-) wire (small black wire with ring terminal) to a suitable chassis bolt or screw ensuring a good
electrical connection is made.
6. Reconnect the main/starting battery’s negative cable (Earth).
TESTING FOR NORMAL OPERATION
1. With the installation complete and the engine ‘Off’ the ‘Engaged’ LED should be off.
2. Start the vehicle’s engine. Once the starting battery reaches 13.4V the VSR will activate and the ‘Engaged’ LED will
illuminate. If the LED does not illuminate within a few seconds, increase the engine RPM to a fast idle allowing the
alternator to generate more current to charge the starting battery.
3. Once the LED illuminates, turn the engine ‘Off’ and switch the headlights and other accessories ‘On’. When the starting
battery voltage falls below 12.8V, the LED will turn off and the VSR will disconnect the auxiliary load.
12V STARTING
BATTERY
NEGATIVE CHASSIS
(EARTH)
12V SWITCH
OVERRIDE WIRE (OPTIONAL)
VSR100, VSR200
CONNECT TO 12V AUXILIARY LOAD
FUSE
Connect to 12V positive source
MAIN AUX
MANUAL OVERRIDE (OPTIONAL)
Connect the override wire to a switch connected to 12V.
It is recommended to use a switch fitted with an LED to indicate when the override function is activated.


Produktspezifikationen

Marke: Projecta
Kategorie: Nicht kategorisiert
Modell: VSR100

Brauchst du Hilfe?

Wenn Sie Hilfe mit Projecta VSR100 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Projecta

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-