Projecta SC220 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Projecta SC220 (12 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 32 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/12
4 STAGE CHARGING
SMART AUTOMATIC 12/24 VOLT
SOLAR CONTROLLER
P/No. SC220, SC245, SC260
2
IMPORTANT SAFETY INFORMATION
Please read this instruction thoroughly before installing the product.
WARNINGS
This charger is designed for indoor use only
Do not disassemble the controller. Take to a qualified person if the unit requires repairing
Lead acid batteries can be dangerous. Ensure no sparks or flames are present when working
near batteries
Eye protection should always be used. Never short circuit the battery
Given sufficient light solar panels always generate energy even when they are disconnected
Accidentalshorting’ of the terminals or wiring can result in sparks causing personal injury or
a fire hazard. We recommend that you cover up the panel(s) with some sort of soft cloth so
you can block all incoming light during the installation. This will ensure that no damage is
caused to the Solar Panel or Battery if the wires are accidentally short circuited
Always install a battery fuse on each circuit including the solar controller
Do not reverse connect the wires to the solar panel or battery
MOUNTING THE DEVICE
The Solar Controller is mounted as below.
The quickest and easiest way to mount the unit is to use self tapping screws and mount the
unit via the four screw holes located on the mounting wings, affix to a flat surface.
12/24 Volt
45 AMP
SOLAR CHARGE CONTROLLER
MENU SET
USB
5V Max. 2.4A
Temp.
Sensor
3
FEATURES
4 Stage charging ensures the battery is charged to the optimum level (Bulk, Absorption,
Equalisation and Float)
Advanced MCU control pulse width modulated (PWM) technology, high efficiency operation
Programmable for Gel, AGM and Conventional lead-acid (WET) Batteries
Built in regulator to prevent your battery from being overcharged. Overcharging occurs when
the charge voltage is unregulated. This can result in premature battery failure
In built regulator prevents your battery from being under charged, in the solar energy field,
battery undercharge often occurs, especially on some conventional Lead Acid batteries; the
unit provides an automatic equalization feature for deeply drained conventional Lead Acid
and AGM batteries, as well as provides a cycling automatic equalizing feature every 28 days
The Smart Controllers can be connected to the battery permanently to keep the battery fully
charged by using a process called “floating”. This means the controller will stop charging
when the battery is full and will automatically start charging the battery as required.
This process will also reduce water loss and help prevent the battery from drying out
Protects your battery from discharge at night. Under low light or no light conditions the solar
panel voltage could be less than the battery voltage. The unit contains a special circuit which
prevents current flowing back from the battery and into the solar panel
LCD display design, dynamically displays device’s operating data and working condition
Dual USB ports (5VDC/2.4A combined Max output) allow power supply charge for
electronic equipment
Built-in external battery temperature sensor. Optional sensor probe also available
(P/No. SC3TMP)
Multi charging protections against reverse polarity, short circuit, over temperature,
over voltage, etc.
IP Rating: IP30
USB Output
Ports
LCD
Menu
Button
Temperature
Sensor Connection
PV
Terminals
Battery
Terminals
Load
Terminals
Set Button


Produktspezifikationen

Marke: Projecta
Kategorie: Nicht kategorisiert
Modell: SC220

Brauchst du Hilfe?

Wenn Sie Hilfe mit Projecta SC220 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Projecta

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-