Projecta SC110 Bedienungsanleitung

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Projecta SC110 (12 Seiten) in der Kategorie niet gecategoriseerd. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/12
1
SOLAR CONTROLLER
P/No. SC110
12 VOLT
4 STAGE CHARGING
2
WARNINGS IMPORTANT PLEASE READ
SC110 is designed for indoor use only
Use SC008 or SC015 for outdoor applications
Do not disassemble the controller. Take to a qualified person if the unit requires repairing.
Lead acid batteries can be dangerous. Ensure no sparks or flames are present when working
near batteries
Eye protection should always be used. Never short circuit the battery
Given sufficient light solar panels always generate energy even when they are disconnected.
Accidental ‘shorting’ of the terminals or wiring can result in sparks causing personal injury or a fire
hazard. We recommend that you cover up the panel(s) with some sort of soft cloth so you can block
all incoming light during the installation. This will ensure that no damage is caused to the Solar
Panel or Battery if the wires are accidentally short circuited
Always install a battery fuse on each circuit including the solar controller
MOUNTING THE DEVICE
The Solar Controller is mounted as below
The quickest and easiest way to mount the unit is to use the two plastic spacers and self tapping
screws supplied and mount the unit to a flat surface.
5723
58
Fig 1.
3
FEATURES
4 Stage charging ensures the battery is charged to the optimum level
Advanced MCU control pulse width modulated (PWM) technology, high efficiency operation
Programmable for Gel, AGM, Conventional lead-acid (WET) and Calcium Batteries
Built in regulator to prevent your battery from being overcharged. Overcharging occurs when the
charge voltage is unregulated. This can result in premature battery failure
In built regulator prevents your battery from being under charged, in the solar energy field, battery
undercharge often occurs, especially on some conventional Lead Acid or Calcium batteries; the unit
provides an automatic equalization feature for deeply drained conventional Lead Acid battery or
Calcium battery, as well as provides a cycling automatic equalizing feature every 28 days
These solar controllers can be connected to the battery permanently to keep the battery fully
charged by using a process called “floating”. This means the controller will stop charging when the
battery is full and will automatically start charging the battery as required. This process will also
reduce water loss and help prevent the battery from ‘drying out’
Protects your battery from discharge at night. Under low light or no light conditions the solar panel
voltage could be less than the battery voltage. The unit contains a special circuit which prevents
current flowing back from the battery and into the solar panel
Colored LEDs to easily indicate the operational status and battery conditions
Digital LCD to directly display battery voltage, charging current, charging capacity (Amp hour),
battery types, full charge and faulty codes
Provides external battery temperature sensor (Optional)
Multi charging protections against reverse polarity, short circuit, over temperature, over voltage, etc.
Surface Mount or Flush Panel Mount options
Conformal-coating circuit boards and plated terminals protect the unit in hostile environments
For use with 12Volt Solar Panel Only. Suitable for solar panels up to
120 Watts (SC110).
SOLAR CHARGE CONTROLLER
AMP/VOLT
BATTERY
TYPE
Hold for 3 seconds
for settings
CHA RG ING S T AT U S BAT T ERY COND IT IO N
12 VOLT
10 AMP
P/No. SC110
Fig 2.

Produktspezifikationen

Marke: Projecta
Kategorie: niet gecategoriseerd
Modell: SC110

Brauchst du Hilfe?

Wenn Sie Hilfe mit Projecta SC110 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung niet gecategoriseerd Projecta

Bedienungsanleitung niet gecategoriseerd

Neueste Bedienungsanleitung für -Kategorien-