Projecta HDBT154 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Projecta HDBT154 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 18 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
Tray Fitting Instructions to suit Auxiliary battery for
Nissan Navara D22 2.5 Litre Diesel
Years: 2008 onwards
HEAVY DUTY DUAL BATTERY TRAY
P/No. HDBT154
2
IMPORTANT SAFETY INFORMATION
Please read this instruction thoroughly before fitting the tray.
This product is recommend to be fitted by a workshop or qualified mechanical person.
WARNINGS
• Before installation, make sure that the vehicle is stationary and the wheels chocked.
• Be careful when laying wires, not to cause any electrical shorts or wire breakage.
• After installation ensure the bonnet can close without hitting the newly installed battery and
battery tray.
• Will not fit if Safari Snorkel is fitted.
• Not suitable for Extreme rock crawling.
• If vehicle is fitted with a Nissan snorkel then tray will fit but may only take a 265mm battery
depending on snorkel fitment. Suitable battery could be Exide P/n: LCS24-86
SPECIFICATIONS
Max Battery Size (mm) L300x W175 x H220 (No Snorkel fitted)
L265 x W175 H220 (Snorkel fitted)
Max Battery Weight 22Kg (No Snorkel fitted) 17Kg (Snorkel fitted)
Recommended batteries Exide LCS 27-97 & Century N70TMF
Approximate fitting time 1 hour
Special tools None required
Recommended Dual P/n: IDC25, DBC100 (can use DBC150), VSR100 (can use VSR200)
Battery System
Tray Location Engine Bay, Passenger Side near radiator support
Special Notes May require a workshop to remove the pre cleaner and seal up the hole
KIT INCLUDES
Hardware
4 x M6 Bolts
2 x M8 Bolts long
2 x M8 Nut
4 x M8 Body Washer
2 x M6 Nut
Special Top
Mount
Tray
J Bolts
3
FITTING INSTRUCTIONS
1. Make sure that the vehicle is stationary, the engine is switched off and cool.
Disconnect the negative battery terminal from the main battery.
2. Place the tray in position, the holes in the tray should line up with the holes in the
body. Pre Cleaner may need to be removed.
3. Bolt the tray in using the M6 bolts. Use the existing 2 captive nuts in the body and
the supplied body washer and nuts for the other 2 holes.
4. Bolt 1 x M8 bolt in the leg of the tray, use the body washer and nut.
Use 1 x M8 Bolt through the radiator support frame use the body washer and nut.
5. Place the battery in the tray, attach the 2 x J bolts, fit the special top mount and
bolt to the radiator support frame.
6. Reconnect the negative battery terminal to the main starter battery or install the
desired Dual Battery System. Before closing the bonnet make sure the battery, tray
and J bolts do not hit the bonnet.
For assistance throughout the installation procedure please call our customer service
representatives on 1800 113 443.


Produktspezifikationen

Marke: Projecta
Kategorie: Nicht kategorisiert
Modell: HDBT154

Brauchst du Hilfe?

Wenn Sie Hilfe mit Projecta HDBT154 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Projecta

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-