Ozito PXSMSK-800MS Bedienungsanleitung

Ozito Nicht kategorisiert PXSMSK-800MS

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Ozito PXSMSK-800MS (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
STANDARD EQUIPMENT
PXSMSK-800MS
INSTRUCTION MANUAL
SPECIFICATIONS
Folded Size: 940 x 545 x 810mm
Length: 940mm (Folded)
1950mm (Extended)
Height: 810mm (Folded)
920mm (Extended)
Loading Capacity: 150kg
Weight: 9.65kg
ozito.com.au
0223
Mitre Saw Stand
2 x Roller Arms, 2 x Mounting
Bars, 2 x Extension Arms
4 x 60mm bolts, 4 x 35mm
bolts, 4 x Washers, 4 x Spring
Washers, 4 x Hex Nuts
4 x Fastening Knobs
MITRE SAW
STAND
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
OZITO INDUSTRIES PTY. LTD. 25 Fox Drive, Dandenong South, VIC 3175, Australia.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other than that specied
on the tool.
• If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty and are excluded from the warranty extension. Warranty excludes
consumable parts.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
Unfolding The Stand
1. Lay the mitre saw stand on the
oor with the folded legs facing
up.
2. Depress the leg locking button
and unfold the 2 upper legs until
the locking button clicks into
place.
3. Repeat the same procedure for the other 2 legs.
4. Lift the stand and ip it into the upright position.
5. Check that the stand is stable
and all of the leg locking buttons
have engaged properly.
Folding The Stand
1 pair of legs on the stand must fold in rst for the stand to fold at. The
legs have not folded into place if the leg locking button does not pop into
place. The legs should not swing about when the stand is picked up if the
legs have locked into position.
1. Turn the mitre saw upside down on the oor with the legs sticking up.
2. Depress the leg locking buttons on the lower pair of legs and fold them
in.
3. Repeat the same procedure on
the other pair of legs.
1. Mounting Bar
2. Fastening Slot
3. Mounting Bar Handle
4. Extension Arm Locking Pin
5. Roller
6. Material Support ShelfRed
MITRE SAW STAND
KNOW YOUR PRODUCT
1. ASSEMBLY
SETUP & PREPARATION
1
2
3 4 5
8
9
11
10
12
13
14
6
7
WARNING! THIS STAND IS INTENDED FOR USE WITH
MITRE SAWS ONLY. DO NOT USE A STEP LADDER,
STEPPING STOOL, STORAGE RACK, ETC.
OZITO WILL NOT BE LIABLE FOR DAMAGE OR INJURY
CAUSED BY IMPROPER USE OF THIS UNIT.
7. Upper Leg Locking Pin
8. Stand Leg
9. Frame
10. Extension Arm Fastening Knob
11. Lower Leg Locking Pin
12. Extension Arm
13. Roller Arm
14. Roller Arm Fastening Knob
Attaching The Extension Arms
1. Slide the extension arms into the
frame.
Note: The locking pin on the extension arms should be facing inwards
towards the centreline of the stand. You will need to depress this twice
(once when the locking pin reaches the frame and again when it pops
through the locating hole further in).
2. Continue sliding the extension arm into the frame until the desired length
is reached.
3. Insert a fastening knob into
the hole on the frame turn it
clockwise to secure the extension
arm in place.
4. Insert a roller arm into the
collar on the extension arm. The
material support shelf should
be facing inwards towards the
centre of the stand.
5. Insert a fastening knob into the
bracket and turn it clockwise to
tighten the roller arm into place.
6. Repeat the same procedure with the opposite extension arm.
Attaching The Extension Arms
1. Depress the mounting bar
handles and hook the opposite
end of the mount onto the frame
of the stand.
2. Lower the handles onto the
frame and release them to lock
the mounting bar into place.
3. Repeat the same procedure with the other mounting bar.
a.
b.


Produktspezifikationen

Marke: Ozito
Kategorie: Nicht kategorisiert
Modell: PXSMSK-800MS

Brauchst du Hilfe?

Wenn Sie Hilfe mit Ozito PXSMSK-800MS benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Ozito

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-