Ozito PXDATK-250 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Ozito PXDATK-250 (10 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/10
STANDARD EQUIPMENT
LOC K
211917
LOCK
211917
LOC K LOC K
PXDATS-018
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 18V
Chuck Size: 2-13mm Keyless /
6.35mm (1/4”) Hex
No Load Speed: 0-450 / 0-1,600/min
Torque Setting: 21
Max. Torque: 45Nm
Drilling Capacities: 32mm (Timber)
13mm (Metal)
Weight: 1.57kg
ozito.com.au
0122
Cordless Multi Chuck Drill
with Straight Chuck & Bit
Holder
Offset Chuck, Right Angle
Chuck & Belt Clip
22 Piece Accessory Kit &
Kitbox
MULTI CHUCK
DRILL
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
OZITO INDUSTRIES PTY. LTD. 25 Fox Drive, Dandenong South, Victoria, Australia 3175.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other than that specied
on the tool.
• If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty and are excluded from the warranty extension. Warranty excludes
consumable parts.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
211917
LO CK LO CK
LO CK
1. Straight Chuck
2. Keyless Locking Collar
3. Integrated Hex Driver
4. Torque Collar
5. Variable Speed Trigger
6. Forward/Reverse Lever
7. Gear Selector
8. Accessory Holder
9. LED Worklight
10. Right Angle Chuck
11. Offset Chuck
This tool is compatible with all batteries & chargers from the Ozito Power X Change
range.
CORDLESS MULTI--CHUCK DRILL
BATTERY & CHARGER
KNOW YOUR PRODUCT
1. ASSEMBLING THE TOOL
SETUP & PREPARATION
1 2 3 4 65 7
891011
Changing The Chuck
WARNING! ENSURE THE TOOL IS SWITCHED
OFF AND THE BATTERY IS REMOVED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
1. Pull the locking collar towards the
front of the chuck and push it onto the
driver on the front of the tool.
2. When the chuck has clicked into
place, release the locking collar.
Note: if the chuck doesn’t click
into place, spin the collet of the chuck until
the locking collar locks into place.
3. To remove the chuck, pull the locking collar forwards again and pull the
chuck off the tool.
Attaching The Belt Clip & Accessory Holder
1. Remove the screw on either side of the tool
base.
2. Push the tabs on the accessory holder into the
slots on the tool and then replace the screw.
3. Repeat the above steps with the belt clip on
the other side of the tool.
Installing The Battery Pack
1. Slide the battery into the tool base
until it clicks into place.
2. To remove the battery, hold down
the battery release button and
slide the battery out.
LO CK
1
a.
b.
LOC K
211917
LOC K
211917
2. ATTACHING ACCESSORIES 3. CONTROLS
OPERATION
Forward/Reverse Lever
1. To drill or drive screws, push the
forward/reverse button towards
the left of the drill.
2. Push the button towards the
right of the tool to reverse the
rotation.
Variable Speed Trigger
1. Squeeze the variable speed
trigger to start the tool.
Note: The more the variable
speed trigger is depressed, the
faster the drill bit will rotate.
2. Release the trigger to stop drilling.
Adjusting Torque
1. Rotate the torque collar to the
desired setting.
Note: Selecting a higher torque
setting will allow the drill to use
more torque to drive the screw in or
out. To prevent damaging the screw
head, it is recommended to start at
a low torque setting and increase
when necessary.
Note: Set the torque collar to the
drill icon when drilling holes.
Speed Control
The gear selector controls the speed of the drill. First gear allows slower
drilling with more torque, while second gear is suitable when less torque
but higher speed is required.
1. Slide the switch backwards to
select rst gear.
2. Slide the switch forwards to
select second gear.
Installing A Drill Bit
The timber drill bits can be used with the straight chuck.
1. Rotate the chuck collar anti-clockwise to open
the chuck.
2. Insert the drill bit, making sure it
is centred in the chuck.
3. Tighten the chuck by turning the chuck collar
clockwise.
4. Pull on the bit to ensure it is rmly secured.
5. To remove the bit, rotate the
chuck collar top open it and
remove the drill bit.
WARNING! DO NOT HANDLE ACCESSORIES
WITHOUT GLOVES AS THEY ARE SHARP & CAN
BECOME HOT AFTER USE, POTENTIALLY CAUSING
INJURY.
Using The Driving Bits
The driving bits and magnetic extension
bit can be used with the integrated hex
driver, the offset chuck and the right
angled chuck.
1. Install the offset chuck or
right angled chuck to suit your
application.
2. Push the required bit into the
driver on the chuck until it clicks
into place.
LO CK
LO C K
211917
LOCK
1
LOCK
211917
LO C
17
FORWARDS
REVERSE
LOCK
1917
LO CK
211917
LOCK
1
2nd Gear
1st Gear
LO CK
WARNING! ENSURE THE TOOL IS SWITCHED
OFF AND THE BATTERY IS REMOVED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.


Produktspezifikationen

Marke: Ozito
Kategorie: Nicht kategorisiert
Modell: PXDATK-250

Brauchst du Hilfe?

Wenn Sie Hilfe mit Ozito PXDATK-250 benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Ozito

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂźr -Kategorien-