Ozito PLHA-001 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Ozito PLHA-001 (6 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/6
CHAINSAW
CUTTING STAND
Ø250mm
INSTRUCTION MANUAL
SPECIFICATIONS
Working Heights: 3 (600, 640, 680mm)
Length: 800mm approx.
Logs: 250mm approx.Ø
Load Capacity: 150kg
Weight: 7.3kg
PLHA-001
STANDARD EQUIPMENT
3 YEAR REPLACEMENT WARRANTY*
Your product is guaranteed for a period of If 36 months from the original date of purchase.
a product is defective it will be replaced in accordance with the terms of this warranty. Warranty
excludes consumable parts, for example: valve adapters and accessories.
*This product is intended for DIY use only and replacement warranty covers domestic use.
WARNING
The following actions will result in the warranty being void.
If the tool has been operated on a supply voltage other than that specified on the tool.
If the tool shows signs of damage or defects caused by or resulting from abuse, accidents
or alterations.
Failure to perform maintenance as set out within the instruction manual.
If the tool is disassembled or tampered with in any way.
Professional, industrial or high frequency use.
WARRANTY
OZITO Australia/New Zealand (Head Office) 25 Fox Drive, Dandenong South, Victoria, Australia 3175.
ozito.com.au
2 x Legs A, B, & C
2 x Cross Struts D & E
1220
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY
YOU MUST RETURN THE PRODUCT TO YOUR NEAREST
BUNNINGS WAREHOUSE WITH YOUR BUNNINGS
REGISTER RECEIPT. PRIOR TO RETURNING YOUR
PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR
CUSTOMER SERVICE HELPLINE:
Australia: 1800 069 486
New Zealand: 0508 069 486
The benefits provided under this warranty are in addition to other rights and remedies which
are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this warranty,
however, where you have suffered any additional direct loss as a result of a defective product
you may be able to claim such expenses by contacting our customer service helpline above.
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE
THE MODEL NUMBER AND DATE OF PURCHASE
AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE
WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS
YOU MAY HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
3 x F Bolt & Nut M8x14
2 x G Screw & Nut M6x28
8 x H Screw & Nut M6x12
2 x I Screw, Nut & Washer M6x12
1. ASSEMBLY
SETUP & PREPARATION
WARNING! WEAR SAFETY GLOVES - TAKE CARE THAT
YOU DO NOT INJURE YOURSELF ON SHARP CORNERS
OR EDGES.
KNOW YOUR PRODUCT
ONLINE MANUAL
Scan this QR Code with your mobile
device to take you to the online manual.
A. Leg A x 2
B. Leg B x 2
C. Leg C x 2
D. Cross Strut D x 2
E. Cross Strut E x 2
CHAINSAW CUTTING STAND
F G
H
BA
E
B A
D
C
H
G
I
F
I
J
F. M8x14 Bolt & Nut x 3
G. M6x28 Screw & Nut x 2
H. M6x12 Screw & Nut x 8
I. M6x12 Screw, Nut & Washer x 3
J. Safety Catch
Assembly of the Stand
The legs are constructed by assembling each half of the structure
and then joining them together.
Tools for assembly (not included): Phillips screwdriver, M10, M13 &
M14 spanners.
1. Lay three legs on the ground, parallel to each other with teeth
facing up.
2. Place cross strut E over each leg, aligning the holes with the
lower holes on each leg.
Note: Leg C is positioned off centre to the left, this will allow
correct alignment with the second half when joining them together.
BA C
D
E
3. Lay cross strut D over E and all
three legs.
4. Once aligned, insert G screw
from the outside and tighten nut
on the inside (only hand tight at
this initial stage).
5. Using H screw and nut loosely
fastening the remaining legs and
cross struts together.
D
G
H
6. Once all the legs and cross struts are joined together and the
fasteners are assembled, use a spanner and screwdriver to
tension the fasteners to complete this half of the structure.
2. SETUP
OPERATION
7. Repeat the exact process, steps 1-6 for the other side, however
leg C is positioned off centre to the right, this will allow correct
alignment with the first half when joining them together.
A C B
E
D
The two halves can now be joined together to complete the stand.
8. Place each side of the
structure back to back and
join each half together using
both F & I fasteners as
shown. Only tighten to the
point where the chainsaw
cutting stand can still be
adjusted/folded. F
I
WARNING! ONLY USE ON LEVEL, NON-SLIP GROUND.
WARNING! THE SAFETY CATCH HAS TO BE SECURELY
LATCHED BEFORE USE.
Height Settings
The chain sawing trestle can be used in 3 different height settings.
The height is set with the safety catch which must always be
latched at the same height on both ends.
Supporting Timber
The serrated edges provide a stable non-slip area to support
when cutting timber.
Ensure the wood you want to saw is securely placed between
the serrated edges.


Produktspezifikationen

Marke: Ozito
Kategorie: Nicht kategorisiert
Modell: PLHA-001

Brauchst du Hilfe?

Wenn Sie Hilfe mit Ozito PLHA-001 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Ozito

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-