Metra 95-6522B Bedienungsanleitung

Metra Kfz-Bausatz 95-6522B

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Metra 95-6522B (16 Seiten) in der Kategorie Kfz-Bausatz. Dieser Bedienungsanleitung war für 2 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/16
APPLICATIONS
METRA. The World’s best kits.metraonline.com1-800-221-0932 © COPYRIGHT 2014 METRA ELECTRONICS CORPORATION
REV. 7/3/2014 INST95-6522B
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
Table of Contents
INSTALLATION INSTRUCTIONS FOR PART 95-6522B
• Double DIN radio provision
Painted matte black
A) Radio trim panel B) Brackets • C) Retaining caps (5 large, 2 small) • D) (5) #8 x 1/2 screws • E) (2) #8 x 3/8” screws
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-6502 • CHTO-02
Antenna Adapter: • 40-CR10
• Panel removal tool Phillips screwdriver
TOOLS REQUIRED
(sub-dash modifications required)
A B C D
E
Dash Disassembly
Dodge Ram 2002-2005 ....................................2-3
Kit Assembly
Double DIN radio provision ................................4-5
95-6522B
1. Unclip the top edge of the trim
panel below the steering column
(it does not have to be removed).
2. Remove the (1) Phillips-head
screw from below the right
A/C vent. (Figure A)
3. Unclip and remove the dash
trim panel. (Figure A)
4. Remove the (4) Philips screws that
secure the radio. Disconnect and
remove the radio.
5. Remove the (4) Philips screws that
secure the a/c controller (save
these screws they will be reused).
6. Remove the (4) Phillips screws that
secure the factory pocket (save
these screws they will be reused).
Continued on next page
Dash Disassembly
(Figure A) (Figure B)
A/C controller
Pocket
95-6522B
Dash Disassembly
(Figure C)
(Figure D)
7. The dash cavity will need to be cut
to make room for the aftermarket
equipment. Cut and remove the
shelf below the factory radio.
Don’t cut away the factory radio
mounting positions.
8. Locate the spots where the two
dash parts are welded together.
Slide a flat head screw driver
between the two plastic panels
and rotate the screwdriver so
that it forces the two plates apart.
(Figure C and D)
Note: If desired, the welds can
be pre-drilled softly with a 1/4”
drill bit to help the welds apart.
Continue to kit assembly
Rear view with
panel removed.


Produktspezifikationen

Marke: Metra
Kategorie: Kfz-Bausatz
Modell: 95-6522B

Brauchst du Hilfe?

Wenn Sie Hilfe mit Metra 95-6522B benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Kfz-Bausatz Metra

Bedienungsanleitung Kfz-Bausatz

Neueste Bedienungsanleitung für -Kategorien-