Lancom LN-1700UE Bedienungsanleitung

Lancom Nicht kategorisiert LN-1700UE

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Lancom LN-1700UE (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

a Power

Off Device switched off

Green, permanently* Device operational,

resp. device paired / claimed and LANCOM

Management Cloud (LMC) accessible.

Orange, permanently No adequate PoE-power supply via

802.3af, operation of the second Wi-Fi

interface not possible

Red / green, blinking Configuration password not set. Without a

configuration password, the configuration

data in the device is unprotected.

Orange / green,

blinking alternately

with the WLAN link

LED

At least one Wi-Fi module is in

managed mode and has not found a

WLAN controller yet. The corresponding

Wi-Fi module(s) is/are switched off until a

WLAN controller has been found to supply

a configuration, or until being switched

manually into another operating mode.

Orange / red,

blinking alternately

with the WLAN link

LED

At least one Wi-Fi module is in managed

mode and has found a WLAN controller.

However, the WLAN controller cannot

assign a configuration because the

firmware and/or the device's loader

version is not compatible with the WLAN

controller.

1x green inverse

blinking*

Connection to the LMC active, pairing OK,

claiming error.

2x green inverse

blinking*

Pairing error, resp.

LMC activation code / PSK not available.

3x green inverse

blinking*

LMC not accessible, resp.

communication error.

b WLAN link

Off No Wi-Fi network defined or Wi-Fi module

deactivated. The Wi-Fi module is not

transmitting beacons.

Green, permanently At least one Wi-Fi network defined and

Wi-Fi module activated. The Wi-Fi module

is transmitting beacons.

Green, inverse flashing Number of flashes = number of connected

Wi-Fi stations and P2P wireless

connections, followed by a pause (default).

Alternatively the flashing frequency can

indicate signal strength over the defined

P2P link or the signal strength between

the access point and the device operating

in client mode.

Green, blinking DFS scanning or other scan procedure

Red, blinking Wi-Fi module hardware error

M O U N T I N G A N D C O N N E C T I N G T H E D E V I C E

Hardware

Power supply 12 V DC, external power adapter (110 V or 230 V) with bayonet connector to secure against

disconnection or PoE based on 802.3at via ETH1

Power consumption Approx. 20.4 W via 12 V / 2 A power adapter

(value solely refers to the power consumption of the access point),

Approx. 22.3 W via PoE

(value solely refers to the power consumption of the access point)

Environment Temperature range 0–40 °C for vertical wall mount with LANCOM Wall Mount (LN),

Temperature range 0–35 °C for horizontal ceiling mount with LANCOM Wall Mount (LN).

Access point overheating is avoided by automatic throttling of the Wi-Fi modules.

Humidity 0-95 %, non-condensing

Housing Robust synthetic housing, rear connectors, ready for wall and ceiling mounting; measures

205 x 42 x 205 mm (W x H x D)

Number of fans None; fanless design, no rotating parts, high MTBF

Bluetooth Low Energy

iBeacon The device can broadcast a configurable iBeacon.

Scanner The device can collect data of BLE devices in the neighborhood and forward this data to

external systems for evaluation purposes.

Interfaces

ETH1 (PoE) 10 / 100 / 1000 Base-TX, autosensing, auto node hub, line bundling via LACP,

PoE adapter compliant to IEEE 802.3at required

ETH2 10 / 100 / 1000 Base-TX, autosensing, auto node hub, line bundling via LACP

Serial interface Serial configuration interface / COM-port (8-pin mini-DIN): 9,600 - 115,000 baud

USB USB 2.0 Hi-Speed Host-Port

Wireless ePaper

Displays

The device is equipped with a Wi-Fi module for actuating LANCOM Wireless ePaper Displays in

the 2.4 GHz frequency band.

iBeacon The device is equipped with a BLE module and thus can transmit a configurable iBeacon.

Declaration of conformity

Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in

compliance with Directives 2014/30/EU, 2014/53/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006.

The full text of the EU Declaration of Conformity is available at the following Internet address:

www.lancom-systems.com/doc

Package content

Documentation Installation Guide (DE / EN), Quick Reference Guide (DE / EN)

Cable Ethernet cable, 3 m

Power adapter External power adapter, NEST 12 V / 2 A DC/S, barrel connector 2.1 / 5.5 mm bayonet,

LANCOM item no. 111590 (EU, 230 V) (not for WW devices)

T E C H N I C A L D E T A I L S

*) The additional power LED statuses are displayed in 5-seconds

rotation if the device is configured to be managed by the LANCOM

Management Cloud.

LANCOM LN-1700UE

Quick Reference Guide

Please observe the following when setting up the device

A For devices to be operated on the desktop, please attach the adhesive rubber

footpads

A Do not rest any objects on top of the device

AKeep the ventilation slots on the side of the device clear of obstruction

aPower

After connecting the cable to the device, turn the connector 90° clockwise to

prevent it from accidental un plugging. Use only the supplied power adapter.

bEthernet interface

Use the cable with the Ethernet connectors to connect interface ETH1 (PoE)

or ETH2 to your PC or a LAN switch.

cReset button

Pressed up to 5 seconds: device restart

Pressed until first flashing up of all LEDs:

configuration reset and device restart

dSerial interface

You can optionally configure the device by connecting it to a PC with a

configuration cable (separately available).

eUSB interface (inner right side)

Connect compatible USB devices either directly to the USB interface, or use a suitable

USB cable.

a b

C ud eadylo -r

ba c d

ALockable wall and ceiling mounting with the LANCOM Wall Mount (LN)

(available as an accessory)

APlease note that when operating both Wi-Fi modules in the same frequency band, mutual

interference cannot be ruled out

Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!

Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.

LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This docu-

ment contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and / or omissions. 111854/01/22