Labelmate Count-100 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Labelmate Count-100 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
© LABELMATE User_C- - - /17 Original user manual. 100 200 CE 05 ● KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE ●
MAINTENANCE:
Your COUNT-100 / COUNT- 200 requires no maintenance.
Product Limited Warranty
All Labelmate Products are warranted to the original end-user customer to be free from defects in
materials and workmanship. If it is determined by Labelmate that a product has failed under the terms of
this warranty, the product will be repaired or replaced at no charge to the customer. Labelmate reserves all
rights to determination of coverage and liability under this warranty. The warranty period for all new
Labelmate products is outlined below:
The warranty period for all products starts on the date purchased by the original end-user customer.
Warranty coverage is not transferable with ownership and will terminate immediately upon rental, resale or
any other change in ownership. This warranty does not cover repair to any product which is damaged, has
been modified, is missing parts, or has been opened or repaired by any unauthorised person. Use of any
unauthorised accessory or attachment will void coverage. Purchase documentation should be retained for
coverage verification.
In the event your product requires service, please contact the distributor you bought the product from. The
customer assumes responsibility for all cost and risk incurred in transport for service.
Labelmate makes no other warranty of any kind expressed or implied, or to suitability or fitness for a
particular purpose. No other person, agent or reseller is authorised to give any warranties on behalf of
Labelmate. Any obligation to warranty other than that specifically addressed above is hereby disclaimed.
Warranty Period
Products Covered
5 years
Label Rewinders
Label Unwinders
3 years
Label Counters (mechanical parts
only)
Label Slitters (mechanical parts
only)
Label Dispensers
Printer Mechanisms
1 year
Power Supply Modules
Counter modules
Encoders
Any products not specified above.
SPRL
290, Chaussée de Ruisbroek, 1620 D , BELGIUM rogenbos
TEL: +32 2.375.69.60 FAX: +32 2.375.38.96
brussels@labelmate.com
www.labelmateeurope.com
Label Counter for use with CAT-3 Label Rewinders
Digital Circuitry for Accuracy and
Repeatability.
Pre-set Counter.
Stops Rewinder when Count is reached.
Remove all parts from the shipping container and verify contents.
PACKAGE CONTENTS:
User Manual (this document)
COUNT-100 or COUNT-200 Counter Unit
Power Supply Module
Retain the Shipping Container and Packaging for Storage and Transport
SPECIFICATIONS:
Weight of the machine: COUNT- COUNT- .100: 7,42Kg 200: 8,13Kg
Max. Label Roll Width: C-100: 170mm (6.7") C-200: 255mm (10").
Power Supply: Input: 220-240VAC -60Hz. Output: 12VDC 50
IMPORTANT INFORMATION:
This product is a label counter. It is only to be used to count labels of the recommended
dimensions in an indoor, dry environment.
The machine has to be unplugged before any manipulation.
The machine is to be used on a flat surface, if the surface is not flat; it is to be fixed using
the holes in the base plate.
Do not leave the power cable in a passageway.
The ambient light of the working area needs to be sufficient to avoid any risk.
The counter can be used in ambient temperatures of +2°C to 40°C.
Connection of the machine to the power source must respect local and European
legislations.
PC-1 PRE-SET COUNTER SET-UP:
1. Verify that the AC/DC Adaptor VOLT CHANGE SW.” is set to and plug 12
it into a suitable AC Power Outlet. Plug the Cord on the AC/DC Adaptor into
the Power Input Jack on the bottom of the Counter Display Module.
2. Plug the Control Cable (with 3.5mm plugs at each end) between the Output
Jack on the bottom of the Counter Display Module and the “EXTERNAL
HALT CONTROL” jack on the CAT-2 Label Rewinder.
3. The Counter is pre-programmed as a Preset Count- Counter. Press each up
of the 6-digits for the count desired. This is the number of labels you wish
to pass through the Label Sensor before the Counter issues a “HALT”
command to the CAT-2 Label Rewinder.
4. Pull a short strip of labels back and forth through the Label Sensor Gap and
observe the count on the Counter increasing. When the preset number of
labels is reached, the PC-1 Counter will issue a Halt Command for the CAT-
2 Label Rewinder to stop. Pressing RESET” will reset the count and restart
the CAT- 2.
5. See the included detailed manual for the Pre-set Counter itself for other
Counter options.
FOR YOUR SAFETY:
Switch off device before any manipulation.
COUNTER USE:
1. Place the COUNT-100 or COUNT-200 Label Counter so that it is
perpendicular to the label web.
2. Observe the Paper Path Label on the Counter: Feed the label web under the
metal Rotating Paper Guide and over the Nylon Fixed Paper Guide.
3. Adjust the position of the rings on the Rotating and Fixed Paper Guides to
the width of your label web. Only finger tighten the screws. The labels must
pass through the black sensor slot between the round Paper Guides.
4. Affix the label web to the label rewind core on the Label Rewinder.
5. The Counter will count the number of labels passing through the sensor air
gap.
NOTE: If you observe erratic counting, clean the Optical Sensor with isopropyl
alcohol.
INTERNAL CIRCUIT PROTECTION:
The COUNT-100 and COUNT-200 Label Counters have an internal device for
circuit protection. There are no user serviceable parts inside. In the event of
operational problems, please contact LABELMATE for assistance.
WARNING!
This Product is for indoor use only.
Not for use in wet locations.


Produktspezifikationen

Marke: Labelmate
Kategorie: Nicht kategorisiert
Modell: Count-100

Brauchst du Hilfe?

Wenn Sie Hilfe mit Labelmate Count-100 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Labelmate

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-