Labelmate CAT-4 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Labelmate CAT-4 (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
© LABELMATE User_CAT-4-CE 7 Original user manual. 05/1 ● KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE ●
MAINTENANCE:
Your CAT-4 requires no maintenance.
Product Limited Warranty
All Labelmate Products are warranted to the original end-user customer to be free from defects in
materials and workmanship. If it is determined by Labelmate that a product has failed under the terms of
this warranty, the product will be repaired or replaced at no charge to the customer. Labelmate reserves all
rights to determination of coverage and liability under this warranty. The warranty period for all new
Labelmate products is outlined below:
The warranty period for all products starts on the date purchased by the original end-user customer.
Warranty coverage is not transferable with ownership and will terminate immediately upon rental, resale or
any other change in ownership. This warranty does not cover repair to any product which is damaged, has
been modified, is missing parts, or has been opened or repaired by any unauthorised person. Use of any
unauthorised accessory or attachment will void coverage. Purchase documentation should be retained for
coverage verification.
In the event your product requires service, please contact the distributor you bought the product from. The
customer assumes responsibility for all cost and risk incurred in transport for service.
Labelmate makes no other warranty of any kind expressed or implied, or to suitability or fitness for a
particular purpose. No other person, agent or reseller is authorised to give any warranties on behalf of
Labelmate. Any obligation to warranty other than that specifically addressed above is hereby disclaimed.
Warranty Period
Products Covered
5 years
Label Rewinders
Label Unwinders
3 years
Label Counters (mechanical parts
only)
Label Slitters (mechanical parts
only)
Label Dispensers
Printer Mechanisms
1 year
Power Supply Modules
Counter modules
Encoders
Any products not specified above.
LABELMATE SPRL
290, Chaussée de Ruisbroek, 1620 Drogenbos, BELGIUM
TEL: +32 2.375.69.60 FAX: +32 2.375.38.96
brussels@labelmate.com
www.labelmateeurope.com
CAT-4
Heavy-Duty "CAT" Label Rewinder
Three Torque Range and
Direction Controls
Constant Adjustable TorqueTM
"CAT" technology
Adjustable Speed Control up to
125cm per second
Precise Variable Speed Control
CAT - 4
REAR PANEL
Remove all parts from the shipping container and verify contents.
PACKAGE CONTENTS:
User Manual (this document)
CAT-4 Drive Unit
Power Supply Module
LABELMATE "Quick- -Locking Core Chuck Chuck" ™ Quick
or Standard Shaft with three (3) metal Vanes installed,
or Model- -INCHES Shaft with six (6) metal Vanes installed, 10
or Model ACH: Adjustable Core Holder
Two 300mm Plastic Flange Plates (One only for QC, none for ACH)
Retain the Shipping Container and Packaging for Storage and Transport
SPECIFICATIONS:
Weight of the machine: 9,6Kg to 11,1Kg depending on model.
Max. Label Roll Weight: STD: 8Kg ACH: 7Kg QC: 8Kg -IN: 10Kg. 10
Max. Label Roll Diam.: 300mm (280mm for ACH).
Start/Stop: ON/OFF Power Switch
Power Supply: Input: 220 240VAC 50 60 Hz – – .
Output: 15VDC 4.3 3A
.
IMPORTANT INFORMATION:
This product is a label rewinder. It is only to be used to rewind or unwind labels of the
recommended dimensions and weight in an indoor, dry environment.
The machine has to be unplugged before any manipulation.
The machine is to be used on a flat surface, if the surface is not flat, it is to be fixed using
the holes in the base plate.
Do not leave the power cable in a passageway.
The ambient light of the working area needs to be sufficient to avoid any risk.
The rewinder can be used in ambient temperatures of +2°C to 40°C.
Connection of the machine to the power source must respect local and European
legislations.
SET-UP:
(if you have the ACH Adjustable Core Holder option Skip to step 4).
1. STANDARD AND 10": Identify the inner Label Flange. Slide the Flange Plate onto the
hollow end of the Rewind Shaft. For maximum width, the Flange face should be flush with
the end of the Shaft. Tighten the screw in the Hub until it is snug. Not too tight.
2. CHUCK: Mount the inner Flange onto the Quick-Chuck with two screws provided.
3. Slide the Shaft d Flange Assembly onto the CAT-4 Motor Shaft allowing for clearance to an
the CAT-4 Chassis and Motor Screws. Tighten the Allen Screw onto the flat part of the
Motor Shaft until it is tight.
4. ACH: Slide the Hub of the ACH over the motor Shaft of the CAT-4 Position the Hub so .
there is a gap between the ACH Hub and the Rewinder Drive Unit case. Tighten the Allen
Screw onto the flat part of the Motor Shaft until it is tight.
5. Set the CAT-4 in place near the label exit slot of the printer.
6. CAUTION: AVOID ACCIDENTS. THE CAT- WEIGHS OVER 10KG, SO CHOOSE ONLY
A STURDY SURFACE ON WHICH TO SET THE UNIT.
7. Verify that the "DIRECTION" Switch on the CAT-4 Control Panel is in the "OFF" position.
8. Plug the Power Plug at the end of the wire on the AC/DC Wall Transformer into the CAT-4
Power Input Jack. Plug the AC/DC Transformer into an appropriate AC power outlet. The
unit is now ready for use.
FOR YOUR SAFETY:
Switch off device before any manipulation.
REWINDING LABELS:
1. Place the "DIRECTION" Switch on the CAT-4 Control Panel in the centre "OFF" position.
2. Slide an empty label core over the Quick-Chuck or Vanes on the shaft until the core is
against the inner Flange Plate. On the Quick-Chuck, tighten the Lock Knob (for an ACH
see the ACH user manual).
3. If desired, slide the outer label Flange Plate (with Ball Plunger in the Hub) onto the Shaft
and up against the label core.
4. Feed the label web from the printer and secure it to the take-up roll core with tape. Rotate
the take-up reel a couple of turns.
5. Place the CAT-4 "TORQUE RANGE" Switch in the "MEDIUM" position. NOTE: When the
"TORQUE RANGE" Switch is in the " -4 develops higher torque. HIGH” position, the CAT
When the "TORQUE RANGE" Switch is in the " -4 develops lower LOW” position, the CAT
torque. Use the "HIGH position for label slitting or rewinding large diameter rolls.
6. Rotate the "SPEED" Control Knob to the minimum position (fully counter-clockwise).
7. Place the CAT-4 "DIRECTION" Switch in the position desired to run left or right.
8. Start the printer and adjust the " " Control Knob for the desired take-up tension. Use SPEED
the minimum " " setting needed to rewind labels properly. Excessive torque might SPEED
pull the labels too hard and cause the printer to lose registration.
EXTERNAL HALT CONTROL:
The CAT-4 can be controlled by the printer. A 3.5mm (mono) connector for an External Control
Input (start/stop) is provided and a matching jack is enclosed. The CAT-4 can react to different
types of signals provided by the printer. The selection of the signal nature is done via 3 jumpers
on the CAT-4 internal PCB. Four modes are selectable: Open Collector High Active, Open
Collector Low Active, Logic Level High Active ( ) & Logic Level Low Active ( Max 10VDC Max
10VDC) By default, the jumpers are on High Active position. . An optional “Start Delay” is
available in order to allow the printer to execute a back feed before starting the print cycle. The
start delay, adjustable from 0-3.5 seconds, will delay the printer after the command has been
received from the printer.
No tension arm option is available.
The factory setting is “Open Collector High”. Other default setting on request.
WARNING!
This Product is for indoor use only.
Not for use in wet locations.
JP3
SIG ACT LOW
OP COL HIGH
X
SIG ACT HIGH
X
OP COL LOW


Produktspezifikationen

Marke: Labelmate
Kategorie: Nicht kategorisiert
Modell: CAT-4

Brauchst du Hilfe?

Wenn Sie Hilfe mit Labelmate CAT-4 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Labelmate

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-