Labelmate CAT-40G Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Labelmate CAT-40G (1 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/1
© LABELMATE User_ 05/17 Original user manual. –TA – – ● KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE ●
Tension Arm for "CAT-TA" Rewinder
Control Arm for "UCAT-3"/"UCAT-40" Unwinders
• CAT-3-TA/CAT- -TA: On-40G
demand Rewinding Turns
Off When Labels Stop
Coming from Your Printer
• UCAT-3 / UCAT-40: On-
demand Unwinding Turns
On When Printer Needs
Labels
CAT-3- -STANDARD TA
UCAT- 40
SET-UP:
1. The Tension Arm/Control Arm is to be mounted vertically. UCAT-40:
CAT-3-TA / CAT- -TA:40G The Tension Arm can be mounted facing either right or
left, depending on which side the labels are coming from.
UCAT-3: The Control Arm can be mounted facing either right or left, depending on
which side the labels need to go to.
2. Remove and keep the large Screw from the end of the Tension/Control Arm Shaft
(the small Shaft below the main Motor Shaft).
3. Loosen the Set Screw at the end of the Tension/Control Arm and position the Arm
with the Set Screw facing the flat on the Tension/Control Arm Shaft.
4. Tighten the Set Screw facing the flat on the Shaft.
5. -insert and tighten the Tension/Control Arm Shaft Screw snugly into the Re
Tension/Control Arm Shaft.
The Unit is now ready for use.
USE POWER REWINDING (CATs): –
1. Run the label web to be rewound under the Rewinder Tension Arm and onto the take-
up label Core on the Rewinder.
2. Place the Rewinder DIRECTION switch in the desired position according to which
direction you want to rewind the labels.
3. Place the REWIND SLIT Switch in the REWIND position and set the TORQUE –
ADJUST about 1/3 rotation from fully CCW as an initial setting.
4. Start your printer and observe how the labels are being rewound.
5. Adjust the TORQUE Control as needed to provide more or less (faster or slower)
rewind power. As the Rewinder winds up the labels, the Tension Arm will rise,
eventually causing the Rewinder to turn off. As the printer feeds more labels that
need to be rewound, the labels and the Tension Arm will drop down, turning on the
Rewinder again.
6. A weight can be placed on the Tension Arm if desired to control the rewind web
tension.
USE POWER UNWINDING (UCATs): –
Refer to your Unwinder User Manual.
SPRL
290, Chaussée de Ruisbroek, 1620 Drogenbos, BELGIUM
TEL: +32 2.375.69.60 FAX: +32 2.375.38.96 –
brussels@labelmate.com
www.labelmateeurope.com


Produktspezifikationen

Marke: Labelmate
Kategorie: Nicht kategorisiert
Modell: CAT-40G

Brauchst du Hilfe?

Wenn Sie Hilfe mit Labelmate CAT-40G benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Labelmate

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-