Joy-it RB-RGBLED01 Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Joy-it RB-RGBLED01 (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
RB
RB
RB
RBRB-
-
-
--RGBLED01
RGBLED01
RGBLED01
RGBLED01RGBLED01
RGB LED Module for Raspberry PI-
1. GENE
1. GENE
1. GENE
1. GENE1. GENERAL INFORMAT
RAL INFORMAT
RAL INFORMAT
RAL INFORMATRAL INFORMATION
ION
ION
IONION
Dear customer, thank you very much for choosing our product.
In following, we will introduce you to what to observe while start-
ing up and using this product.
Should you encounter any unexpected problems during use,
please do not hesitate to contact us.
2. USAGE WITH A RASPBERRY PI
2. USAGE WITH A RASPBERRY PI
2. USAGE WITH A RASPBERRY PI
2. USAGE WITH A RASPBERRY PI2. USAGE WITH A RASPBERRY PI
2.1 Installation of the Soî …ware
If you already use the most current Raspbian System on your Rasp-
berry Pi, you can simply skip this step and proceed with Step 1.2.
Please use the program to install the current „Win32 Disk Imager“
Raspbian image on your SD card. You will find the download of it, if
you follow this link.
Choose your device by browsing through your files and save the file
with Write.
2.2 Connecting the module
Attach the module onto the pins 1 to 26 of your Raspberry Pi, like
shown in the picture below.
Make sure, that the RGB LED of the module is showing towards the -
inside.
2. USE WITH A RASPBERRY PI
2. USE WITH A RASPBERRY PI
2. USE WITH A RASPBERRY PI
2. USE WITH A RASPBERRY PI2. USE WITH A RASPBERRY PI
2.3 Preparing the module
Once you have started the system, open the terminal console and
execute the following commands:
sudo apt get update-
sudo apt get install gcc make build essential python- - -
dev git scons swig
sudo nano /etc/modprobe.d/snd- blacklist.conf
Now open the configuration file with :
sudo nano /boot/config.txt
We install the required packages and confirm them with the
Y
Y
Y
YY
key:
For use, the audio output must be deactivated. For this purpo-
se we process the files responsible for this. We open it with the
command:
backlist snd_bcm2835
Add the following line:
Save and exit the file with the key combination:
CTRL + O , ENTER , CTRL + X
CTRL + O , ENTER , CTRL + X
CTRL + O , ENTER , CTRL + X
CTRL + O , ENTER , CTRL + XCTRL + O , ENTER , CTRL + X
Scroll down the file to the lines:
#dtparam=audio=on
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
Now comment out the bottom line with a hashtag # so that it
looks like this :
Save and exit the file with the key combination:
CTRL + O , ENTER , CTRL + X
CTRL + O , ENTER , CTRL + X
CTRL + O , ENTER , CTRL + X
CTRL + O , ENTER , CTRL + X CTRL + O , ENTER , CTRL + X
The Raspberry PI must be restarted with the following com-
mand:
sudo reboot


Produktspezifikationen

Marke: Joy-it
Kategorie: Nicht kategorisiert
Modell: RB-RGBLED01

Brauchst du Hilfe?

Wenn Sie Hilfe mit Joy-it RB-RGBLED01 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Joy-it

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-