Joblotron RP-01 Bedienungsanleitung

Joblotron Sicherheitskamera RP-01

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Joblotron RP-01 (2 Seiten) in der Kategorie Sicherheitskamera. Dieser Bedienungsanleitung war für 25 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/2
Contactless access control system RP-01 1/1 VAB50202
Contactless access control system RP-01
This device works as a reader of chips (PIT) or cards (PIT). You can
program it with buttons or PC application. This product provides data
connection (RS485), therefore it can be used even for industrial
applications.
1. Technical parameters
Operating Voltage 9 ÷ 16V DC or 8 ÷ 12V AC
Standby current 35mA
terminals NO,C,NC output relay – switching contact max. 1A/125V
operation:
control unit – II. indoor use (-10°C to +40°C)
reading unit – outdoor use (IP46) (-30°C to +60°C)
dimensions (control unit) 2,99 in (w) x 4,3 in (h) x 1,299 in (d)
JabloPCB s.r.o. declares this product is in an agreement with common
requirements and other related EU regulations.
The original of the statement is posted at www.jabloPCB.cz
website in
section Technical support.
2. Installation and basic functions RP-01
2.1. Device installation
MOD SEL SET
RELE
12 VNO C NC
Interface RS-485LCD connector
Setting buttons
MOD SELSET
Connector
reading device
Output relay
Power
Control unit Reader unit
image no 1
The control unit is designed for an indoor installation. During
installation please respect placement of the reading unit as it is
connected with 1m long wire. The reading unit can be placed outdoors.
Warning: reading unit’s wire can be shortened to 0,5m. Replacement
with the different one or extension is disabled as device will not function
correctly.
• prior to control unit installation remove the plastic cover
• take an LCD off the control unit by pulling it out – display is
attached with connector (see image no 1)
• connect the reading unit to the connector (see image no 1)
• check and attach power to the 12V terminals
• place and fit the unit in the desired space
• return LCD back to the original placement (pay extra attention
to attaching to the connector)
• switch the control unit‘s power on
• you will see a basic initialization on the LCD
• and the unit is ready to be used
2.2. Basic setup
Unit was already set in the factory and is ready to learn (program)
individual positions. There are 999 position available + master chip
position.
2.3. Unit learning (PIT – chips and cards)
Programming is possible either with PC controlling software (you
need to connect interface SW-01) or manually with buttons placed
under the LCD and instructions on the screen.
The Master Chip necessary to enter the learning mode is included in
the package.
Table – reading unit indicator signals
indicator Description
No light Ready to program
Green light PIT was identified and successfully learned
learning
Red light PIT was already programmed to a different
position
No light Unit is ready to read PIT
Green light PIT authorized to enter – relay ties
Pulse
mode
Red light PIT unauthorized to enter – relay doesn’t tie
Green light Relay OFF
Red light Relay ON
Switching
mode
No light Unknown PIT is read and indicator switches off
for 1s
Manual way:
There are MOD button and Master Chip to enter the programming
mode.Press and hold the MOD button for at least 2s and display will
show „check MASTER“. On this command place Master Chip on the
reading unit. Following that you will gain access into the learning mode
and first available position for programming individual PIT will be
offered.
If you don’t want to start learning individual PITs from this position you
can set any position by pressing the SEL button.The bottom row on the
screen displays the position selection options (with each press of the
SEL button).
SEL button setting options:
Position +100 and consequently every press of SET button – position
is set for hundreds 100, 200, 300...
Position +10 and consequently every press of SET button – position is
set for tens 10, 20, 30...
Position +1 and consequently every press of SET button – position is
set for ones 1, 2, 3...
(settings can be combined. For example you can set 100 then 10 and 3
= result is learning position 113)
RELAY time – see point 2.5
DELETE ? – current position will be deleted by pressing the SET button
Return to the learning mode
Setting of each option is made by pressing the SET button (it has got a
repeat function when pressed and held). Press MOD button to end
settings.
To exit learning mode press and hold MOD button. Device will go into
standby mode.
It is possible to re-program or delete any position except a learning
position „master position“ (see point 2.4).
Programming using PC application is more convenient as you can work
with files like CSV (export from Excel). The first column has to be a
learning position and the second column needs to be selected PIT´s
manufacturing code. Ignore the other possible columns.
Warning:
During learning new PIT chip on an available position or into an empty
space (caused by deleted position) follow these instructions.
Access the learning mode (see point 2.3). When first available position
is offered, programm PIT by placing it on the Reading Unit. Also you
can decide which position to use at this stage. After the process of
programming the Reading Unit will offer you the next one up position. In
case this position has already been programmed to a PIT and you
use this position to learn a new PIT, the previous one will be
deleted.
Contactless access control system RP-01 2/2 VAB50202
2.4. Master position – programming and deleting
The master position has got a privileged status – reprogramming
causes deleting all PITs learned so far!!
Master position programming:
Access the learning mode. With SEL button select „position+100“ and
by pressing the SET button repeatedly select position 9xx. Press the
SET button once again and get „MASTER LEARNING“ programming
mode. Place a PIT chip and program or reprogram the master.
Master position´s content deleting:
Access the learning mode. With SEL button select „position+100“ and
by pressing the SET button repeatedly select position 9xx. Press the
SET button once again and get „MASTER LEARNING“ programming
mode. With the SEL button select „DELETE ?“ position and confirm
with SET button. This is the way to delete the content of the master
position.
In case there is no PIT programmed on the master position, just press
and hold the MOD button to access the learning mode.
2.5 Relay tie timing
To set use the MOD button. Sign „(INSERT CARD)“ displays on the
LCD when the MOD button is pressed for at least 2s. Choose the
„RELAY time“ (on the LCD bottom row) by pressing the SEL button
repeatedly. Setting is made by SET button. Interval is per second 1-9s.
Confirm your choice with MOD button. To exit learning mode press and
hold MOD button. Device will go into standby mode.
2.6. Relay´s switching mode setting
Device can be set into a switching mode where every change of output
relay status is conditional on placing programmed PIT.
To set use the MOD button. Sign „(INSERT CARD)“ displays on the
LCD when the MOD button is pressed for at least 2s. Choose the
„RELAY time“ (on the LCD bottom row) by pressing the SEL button
repeatedly. Setting is made with SET button when 0s value is chosen.
Confirm your choice with MOD button.To exit learning mode press and
hold MOD button. Device will go into standby mode.
Československé armády 4344
Jablonec nad Nisou
PSČ: 46601
Tel: 483 515 515 fax: 483 515 550
E-mail: jablopcb@jablopcb.cz

Produktspezifikationen

Marke: Joblotron
Kategorie: Sicherheitskamera
Modell: RP-01

Brauchst du Hilfe?

Wenn Sie Hilfe mit Joblotron RP-01 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Sicherheitskamera Joblotron

Joblotron

Joblotron AN-80 Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron JA-80A Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron UC-222 Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron JS-20 Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron AC-83 Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron RC-22 Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron JA-60N Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron JA-83K Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron JA-65ST Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron PG-4M Bedienungsanleitung

10 Juni 2023

Bedienungsanleitung Sicherheitskamera

Neueste Bedienungsanleitung für -Kategorien-

Speco Technologies

Speco Technologies O2PTZ34D5W Bedienungsanleitung

14 August 2024
ZKTeco

ZKTeco BL-34F26L Bedienungsanleitung

11 August 2024
Moxa

Moxa VPort 26 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 36 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 16-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 16-M12-CAM3L54160N Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort P06 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPORT P06-1MP-M12-CAM80 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 16-DO-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 26A-1MP Bedienungsanleitung

27 Juni 2024