Joblotron AC-83 Bedienungsanleitung

Joblotron Sicherheitskamera AC-83

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Joblotron AC-83 (2 Seiten) in der Kategorie Sicherheitskamera. Dieser Bedienungsanleitung war für 27 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

The AC-83 wireless output relay module 1 / 2 MJT51401

The AC-83 wireless relay output module

The AC-83 is a component of Jablotron’s Oasis system. It provides 3

relays which can be controlled by radio signals. The AC-83 is mains-

powered. The device is suitable for heating control via signals received

from wireless thermostats of the TP-8x series. You can use the device

in the following combinations:

o With PGX and PGY outputs of a JA-8x control panel equipped

with a radio module (for switching between heating modes).

o With RC-8x remote controls (for switching between heating

modes).

o With JA-80M or JA-82M magnetic door-detectors (for heating

enablement or disablement).

RADIO

max F 5 A / 250V

buttons

LEDs

fuse

max 5 A

holes to route

a fixing belt

Installation

Installation of this module shall only be undertaken by

technicians holding a certificate issued by an authorized

distributor.

Warning: this device is galvanically connected to the

mains.

Open the module’s cover (1 screw) and take out the circuit board (2

tabs). Install the back part of the housing to the desired place, re-install

the circuit board, connect the wires and enroll the desired wireless

devices.

Terminals

L, N, N Power 230V/50Hz (N, N is a pair of connected terminals)

Lp Normally open contact for the Z common relay

L1 Normally open contact for the X output relay

L2 Normally open contact for the Y output relay

All normally open contacts are fused by a common 5 Amp fuse –

the total combined consumption of the terminals must not exceed

this limit.

Warning: The mains power output does not

provide mains isolation for safety!!

Function description

The X and Y relays are totally independent. Jablotron TP-8x

wireless thermostats can be enrolled to them individually using the X

and Y enrollment buttons. In parallel to thermostats, either remote

controls or a JA-80 control panel can be enrolled (however, these

devices cannot be used in a simultaneous combination) to control

switching the thermostat modes. In addition to the previously

mentioned, wireless magnetic door-detectors can be enrolled and

subsequently used to control the disabling of the heating.

The Z relay is designed to control a heating circulation pump. It

reacts to the logical OR sum of the X and Y relays – the Z output is

closed if, and only if, at least one of the X or Y relays is closed.

All three relays are used in combination to provide “pump cleaning”.

This function is realized by the simultaneous activation of the X, Y and

Z relays for 6 minutes every 7

th day. This is especially useful in the

summer, when the heating system is out of operation. By such

activations a reduction of sediments is achieved in the heating system

and in the pump in particular. The function is not optional – it cannot be

disabled.

Enrollment procedure

• Up to 8 wireless devices (thermostats, magnetic door-detectors,

control panel, remote controls) can be enrolled to each X or Y relay.

• Use the X or Y button depending on which relay you want to enroll

a device to.

• Enter enrollment mode (this is indicated by red LED No. 2 or 4

flashing) by pressing the button.

Use a safe insulation tool for button handling.

• Activate the device’s transmitter while the LED is flashing, as

follows:

o Thermostat (should be enrolled first) – connect its battery up (if

it has already been connected, first disconnect it, and then wait

10 seconds).

o Control panel PG output – key in 299 in service mode.

o Key fob – press a button.

o Magnetic door-detector – connect its battery up (if it has

already been connected, first disconnect it, and then wait 10

seconds).

• Enrollment is confirmed by a short flash from all AC-83 indicators.

• If no enrollment signal has been received within 10 sec.,

enrollment mode automatically ends.

• If you wish to enroll another device, repeat the above enrollment

procedure.

Notes:

• An overview of applicable control devices is provided in the table

below together with their enrollment methods and basic

descriptions of use.

• If a device does not enroll, either it is too far from the receiver, or

too close, or the maximum number of devices (= 8) has been

exceeded.

• Each transmitting device (keyfob, detector, control panel, etc.) can

be enrolled to an unlimited number of different receivers.

• Devices are enrolled to a non-volatile memory, so the AC-83 will

not forget them if its power is disconnected.

Control

device Enrolled by Notes

PGx output

on the

control

panel

Keying in

299 in

Service

mode

switching between heating modes (anti-

freeze / temperature regulation)

- cannot be used in combination with

remote controls

Remote

control

Pressing any

button

switching between heating modes (anti-

freeze / temperature regulation)

- cannot be used in combination with a

control panel

Magnetic

door-

detector

Inserting a

battery

sensor activation (door or window

opening) disables standard temperature

regulation mode

- cannot be used in combination with

remote controls

Use with TP-8x thermostats

• If a single thermostat is enrolled to a relay without any other

devices enrolled in parallel, the relay will switch the heating on or

off, according to signals from the thermostat.

• If multiple thermostats are enrolled, the corresponding relay

switches on if at least one of the thermostats requires the heating to

be switched on.

• The enrollment of a thermostat to a relay is indicated by green LED

1 for relay X and green LED 3 for relay Y.

• Heating activation is indicated by red LED 2 for relay X and red

LED 4 for relay Y.

• Other devices can be combined with a thermostat and all be

enrolled to the same relay (a total of 8 devices, including the

thermostat).

The AC-83 wireless output relay module 2 / 2 MJT51401

Primary device Control device Enrollment

method Notes

Control panel PG

output Enter 299 in

Service mode

• Allows for heating mode switching (temperature regulation/antifreeze).

• Not recommended for use in combination with other remote controls.

Remote control Press any button • Allows for heating mode switching (temperature regulation/antifreeze) via a remote control.

Thermostat

Magnetic door-

detector Connect the battery • When triggered (a door/window is opened), the heating mode switches to antifreeze.

• Wireless devices enrolled together with a thermostat to a single

relay can be used to determine how that relay reacts to signals from

the wireless thermostat. If desired, the relay can react only to the

freezing protection signal from the thermostat to turn on the heating

when the temperature gets below about +6C, or alternatively it can

react to the thermostat signal which demands heating when the

room temperature is lower than that pre-programmed in the

thermostat. The relay can be switched between these two modes

by operating the wireless devices.

• The thermostat repeats its signal every 9 minutes, so if the AC-83

power is turned off for a while, and then on again, the relay will

synchronize with the thermostat within 9 minutes.

Use with a JA-8x OASiS control panel

Using an OASiS control panel with a thermostat in a combination is

only possible with the thermostat enrolled before the control panel. PG

outputs should be programmed in the control panel to have an

ON/OFF function. The PGX output can only be enrolled to the X relay,

and PGY to the Y relay.

• If the control panel is enrolled to the X relay (by entering 299)

then the X relay is switched on whenever the corresponding

thermostat is activated and the control panel’s PGX output is active.

• If the control panel is enrolled to the Y relay (by entering 299)

then the Y relay is switched on whenever the corresponding

thermostat is activated and the control panel’s PGY output is active.

• Only one control panel PG output can be enrolled to each relay.

The control panel PG output allows the switch between temperature

regulation/antifreeze modes to be controlled either by the system

keypad or remotely via a mobile phone or the Internet.

Avoid enrolling key fobs to the same relay to which thermostat(s) and

PG outputs are enrolled as the control panel repeats currently valid PG

signals every 9 minutes. (The signals from the control panel would

override signals from the controller.)

Though the control panel’s requests to switch the heating mode

are recognized instantly, the relay will not react until a

subsequent thermostat signal is received (within 9 minutes).

Use with JA-80M (JA-82M) magnetic door-detectors

Heating mode switchover by thermostat can be overridden by a

JA-80M or JA-82M magnetic door-detector signal (or also signals from

a JA-80D universal transmitter). If such a detector is used, then

triggering the detector switches the heating to antifreeze mode, and

de-triggering the detector switches to regulation mode (regulating the

heating to a pre-programmed temperature).

Though the JA-80M/JA-82M requests to switch the heating mode are

recognized instantly, the relay will not react until a subsequent

thermostat signal is received (within 9 minutes).

When used in combination with an OASiS control panel, magnetic

door-detector activation status is of higher priority: At least one of the

detectors being triggered enforces antifreeze mode regardless of PG

output signals.

Magnetic door-detectors cannot be used in combination with remote

controls.

Use with RC-8x remote controls

You can switch heating modes via a remote control. Pressing the

(or ) button switches the relay to regulating the heating to the

(comfortable) pre-programmed temperature, pressing (or )

switches the relay to regulating the heating to the anti-freeze

temperature.

Though the RC-8x requests to switch the heating mode are

recognized instantly, the relay will not react until a subsequent

thermostat signal is received (within 9 minutes).

Using remote controls for switching between heating modes

cannot be combined with control panel use or with magnetic-door

detectors.

Resetting the AC-83 unit

As a factory default, the AC-83 is supplied with nothing enrolled. To

reset a particular relay, do the following:

• Repeatedly press the X button (or the Y button for the Y relay) to

achieve several LED flashes.

• Then, continuously press the same button and keep pressing it (for

approx. 4 seconds) until all the LEDs flash a couple of times (=

reset). Then release the button.

Technical specification

Power supply 230V/50Hz, class protection II

Consumption about 1W

Relay contact rating

resistive load max. 2,5A / 250V AC

inductive (capacitive), lamp load max. 0,5A / 250V AC

Required fuse rating max. 5A

Communication band 868 MHz, Oasis protocol

Device enrollment is stored in non-volatile memory –

unaffected by power disconnection

Minimum distance from transmitting devices 1 meter

Operating environment general, indoor –10 to +40 °C

Enclosure IP40 EN 60529

Mechanical immunity IK08 EN 50102

Can be operated according to ERC REC 70-03

Complies with ETSI EN 300220, EN 50130-4, EN 55022,

EN 60950-1

Jablotron Ltd. hereby declares that the AC-83 is in

compliance with the essential requirements and other

relevant provisions of Directive 1999/5/EC. The original of

the conformity assessment can be found on the web site

www.jablotron.com, Technical Support section.

Note: Although this product does not contain any harmful

materials we suggest you return the product to the dealer or

directly to the manufacturer after use.

Produktspezifikationen

Marke:	Joblotron
Kategorie:	Sicherheitskamera
Modell:	AC-83

Brauchst du Hilfe?

Wenn Sie Hilfe mit Joblotron AC-83 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Sicherheitskamera Joblotron

Joblotron AN-80 Bedienungsanleitung

10 Juni 2023

Joblotron JA-80A Bedienungsanleitung

10 Juni 2023

Joblotron UC-222 Bedienungsanleitung

10 Juni 2023

Joblotron JS-20 Bedienungsanleitung

10 Juni 2023

Joblotron AC-83 Bedienungsanleitung

10 Juni 2023

Joblotron RC-22 Bedienungsanleitung

10 Juni 2023

Joblotron JA-60N Bedienungsanleitung

10 Juni 2023

Joblotron JA-83K Bedienungsanleitung

10 Juni 2023

Joblotron JA-65ST Bedienungsanleitung

10 Juni 2023

Joblotron PG-4M Bedienungsanleitung

10 Juni 2023

Bedienungsanleitung Sicherheitskamera

Neueste Bedienungsanleitung für -Kategorien-

Speco Technologies O2PTZ34D5W Bedienungsanleitung

14 August 2024

ZKTeco BL-34F26L Bedienungsanleitung

11 August 2024

Moxa VPort 26 Bedienungsanleitung

27 Juni 2024

Moxa VPort 36 Bedienungsanleitung

27 Juni 2024

Moxa VPort 16-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024

Moxa VPort 16-M12-CAM3L54160N Bedienungsanleitung

27 Juni 2024

Moxa VPort P06 Bedienungsanleitung

27 Juni 2024

Moxa VPORT P06-1MP-M12-CAM80 Bedienungsanleitung

27 Juni 2024

Moxa VPort 16-DO-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024

Moxa VPort 26A-1MP Bedienungsanleitung

27 Juni 2024