Joblotron PG-4M Bedienungsanleitung

Joblotron Sicherheitskamera PG-4M

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Joblotron PG-4M (1 Seiten) in der Kategorie Sicherheitskamera. Dieser Bedienungsanleitung war für 21 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/1

PG-4M Pager Receiver 2/2 MEG51607

PG-4M Pager Receiver

The PG-4M pager receiver is designed for reception of signals from

PG-4T pager transmitter. The receiver indicates the reception optically

and acoustically and built-in relays can trigger another devices too. Up

to 4 transmitters PG-4T can be enrolled to onePG-4M.

Technical Specification

Power supply 10 - 16 V =

Current consumption stand-by 10 mA, max. 50 mA

Working frequency 448.17 MHz

Working distance form transmitter max. 2 km (open area)

Operating temperatures -10 °C to +50 °C

Indication acoustic and optical

Relay outputs NO, 60 V / 1A =

In Norway and Belgium can be operated according to ERC REC 70-03

as e SRD, in another countries it has to be licenced.

Complies with:

ETSI EN 300 220/2000, ETS 300683/1998, EN 60650/1997

Hereby, Jablotron Ltd., declares that this PG-4M is in compliance with

the essential requirements and other relevant provisions of Directive

1999/5/EC. Original of the conformity assessment can be found at the

web page www.jablotron.cz, section Technical support.

Note: Although this product does not contain any harmful materials we

suggest you to return the product to the dealer or directly to the

producer after usage.

Installation

• The receiver is designed for indoor use. It should be installed with the

antenna in a vertical position. Do not install the receiver close to metal

surfaces, which could reduce the radio communication.

• Open the cover of the unit by pressing in the internal tab on the top

(small flat screw-driver is appropriate). You can remove the PCB after

you loosen the central screw.

• Route wires through the hole in the bottom of the rear housing. Attach

the housing to the desired place.

• Connect wires to terminals. Replace the cover.

• Connect the power supply. You can use a DC adapter or preferable a

backup power supply (e.g. BP-12).

• In order to increase the working distance, you can use an external

antenna AN-01A or AN-02A. The external antenna should be

connected to the ANTENNA connector. When using an external

antenna, remove the internal rod one (loosen its screw). This way the

working distance can be increased.

• If the PG-4M is used as a part of a security system, it should be

placed in a tamper-protected box. If the box is made of metal then an

external antenna should be used.

Enrolling a transmitter to the receiver

Press and hold the LEARN / RESET button until the A LED blinks.

This indicates entering the enrolling mode.

When any input of PG-4T is triggered, the transmitted channel is

enrolled to the PG-4M. Successful enrollment is confirmed by lighting

up of LEDs.

The receiver is ready to receive signals from enrolled transmitter

now.

Operating mode

Select one of the operating modes setting the „Follow / Pulse“

jumper:

FOLLOW mode

In the “Follow“ mode the output relays copy the status of the PG-4T

inputs.

LED A & relay A is ON when input A of the PG-4T is connected to GND.

LED B & relay B is ON when input of the PG-4T is connected to GND. B

Note: The PG-4M receivers in the FOLLOW mode doesn´t react on the

transmitter’s signal that was triggered by powering the transmitter when

both A and B inputs are disconnected from GND (except the enrolling

mode). If any input is connected with GND when the transmitter is

powered, then the corresponding output relay of PG-4M will be switched

on. But it will remain switched even after deactivating the transmitter!

It is not recommended to use multiple transmitters in this mode.

PULSE mode

If the jumper is in the „Pulse“ mode, output relays switches for 5 sec

after the corresponding triggering input is switched on or off.

LED A & relay A indicate connecting or disconnecting of transmitter’s

input A to GND.

LED B & relay B indicate connecting or disconnecting of transmitter’s

input B to GND.

Note: In the PULSE mode the receiver will indicate alarm on the B

channel if the transmitter is connected to the power supply.

If more transmitters are enrolled, then the receiver will trigger A

alarm if any A input is triggered and input is triggered. B alarm if any B

Optical indication

Status LED Indicates

ON A or B Channel triggered in FOLLOW mode

Blinks slowly A or B Channel triggered in PULSE mode.

Blinks additional 15 minutes after the

relay resets (alarm memory)

Blinks A Enrolling mode

Blinks 3 times A alt. B Reset

Note: The channel A LED blinks after the power supply is switched on.

The number of flashes corresponds to the number of enrolled

transmitters.

Acoustic indication

If any relay is triggered, the built-in buzzer beeps for 15 sec.

Different sounds are generated in order to distinguish the channel

A B (--- --- ---) or (… … …).

Note: The sound corresponds to the latest received signal. You can

switch the buzzer off if you disconnect the BUZZER OFF jumper.

Reset

You can delete all enrolled transmitters and reset the relays if you

press and hold the LEARN / RESET button too a long time. It is

confirmed by LEDs alternating blinking and a short beep.

If you press the LEARN / RESET button shortly, the relays and the

buzzer will reset.

Produktspezifikationen

Marke:	Joblotron
Kategorie:	Sicherheitskamera
Modell:	PG-4M

Brauchst du Hilfe?

Wenn Sie Hilfe mit Joblotron PG-4M benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Sicherheitskamera Joblotron

Joblotron AN-80 Bedienungsanleitung

10 Juni 2023

Joblotron JA-80A Bedienungsanleitung

10 Juni 2023

Joblotron UC-222 Bedienungsanleitung

10 Juni 2023

Joblotron JS-20 Bedienungsanleitung

10 Juni 2023

Joblotron AC-83 Bedienungsanleitung

10 Juni 2023

Joblotron RC-22 Bedienungsanleitung

10 Juni 2023

Joblotron JA-60N Bedienungsanleitung

10 Juni 2023

Joblotron JA-83K Bedienungsanleitung

10 Juni 2023

Joblotron JA-65ST Bedienungsanleitung

10 Juni 2023

Joblotron PG-4M Bedienungsanleitung

10 Juni 2023

Bedienungsanleitung Sicherheitskamera

Neueste Bedienungsanleitung für -Kategorien-

Speco Technologies O2PTZ34D5W Bedienungsanleitung

14 August 2024

ZKTeco BL-34F26L Bedienungsanleitung

11 August 2024

Moxa VPort 26 Bedienungsanleitung

27 Juni 2024

Moxa VPort 36 Bedienungsanleitung

27 Juni 2024

Moxa VPort 16-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024

Moxa VPort 16-M12-CAM3L54160N Bedienungsanleitung

27 Juni 2024

Moxa VPort P06 Bedienungsanleitung

27 Juni 2024

Moxa VPORT P06-1MP-M12-CAM80 Bedienungsanleitung

27 Juni 2024

Moxa VPort 16-DO-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024

Moxa VPort 26A-1MP Bedienungsanleitung

27 Juni 2024