Joblotron JA-80Q Bedienungsanleitung

Joblotron Sicherheitskamera JA-80Q

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Joblotron JA-80Q (1 Seiten) in der Kategorie Sicherheitskamera. Dieser Bedienungsanleitung war für 30 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/1

JA-80Q module 2/2 MKE52702

The JA-80Q photo transmission module

The JA-80Q is a component of Jablotron’s Oasis JA-80 system. It is

designed for transmitting photographs between a wireless detector

equipped with a camera and a communicator of type JA-80Y (GSM/GPRS)

or JA-80V (LAN/TEL). The module is to be installed within the control panel

housing.

Installation in the control panel

If you purchased the module separately, it should first be installed in

the Oasis control panel as follows:

1. The control panel power must be switched off (both mains and

battery)

2. Plug the JA-80Q module (in the control panel) into the same digital

bus connector that is designed (by default) for a JA-80Y connection.

3. For the parallel use of a JA-80Y communicator, if any, use the

connector available on the JA-80Q to connect the communicator.

Control panel

main

board

The

communicator

board

JA-80Y

JA-80Q emodul

Communicator connection

Fig. 1 Module wiring

Enrolling camera-equipped detectors

Installation shall only be undertaken by technicians holding a certificate

issued by an authorized distributor.

1. Enter service mode on the control panel and press key 1 to enter

enrollment mode (see the control panel manual).

2. Enroll the JA-84P detector to the control panel by connecting its

battery (see the JA-84P manual).

3. Exit enrollment mode on the control panel.

Note: If the detector had been enrolled to the control panel before

JA-80Q installation, you do not have to re-enroll it to the system. Instead,

you only need to enter enrollment mode and exit it afterwards. This way the

module will retrieve all the relevant information from the control panel.

Programming the communicator

Successful transmission to the web server running a picture viewer

requires the server IP address to be programmed in the JA-80Y or

JA-80V communicators. The URL address of Jablotron’s picture viewer is

http://img.jablotron.com. IP adress is : 77.104.220.129 port 7070

1. Enter service mode on the control panel.

2. Program the required IP address together with the port used for

data transfer using Comlink software (go to the ARC tab panel) or by

keying in the sequence:

013 *8 xxx xxx xxx xxx yyyyy *0

where: xx..x is a 12 digit IP address and

y..y is a 5 digit number specifying the port. See also

the manual of the communicator.

Example: 013



8 077.104.220.129 07070



3. Exit service mode on the control panel.

Important notes:

The setting or change in the parameter is valid after escaping

service mode.

The SMS information about a new picture on the server is sent to all

phone numbers which are set to get reported event number 01 “Intruder

alarm - instant”. This information contains a link to the new picture on

the server. This feature is available on the JA-80Y from software version

XA61009 and on the JA-80V from software version XA64005.

LED signalling

After taking a photo using the detector’s camera the picture is

transmitted to the control panel and subsequently to the JA-80Q module via

the digital bus. This is indicated by green LED flashing. Successful

transmission is confirmed by a long green flash (2 sec). Unsuccessful

transmission is indicated by a series of rapid green flashes at the end.

Having been successfully received by the JA-80Q module, the picture

is then transferred via the communicator to the pre-programmed web

server. This transfer is indicated by a red LED flashing on the JA-80Q

module. Successful transfer is confirmed by a long red flash (2 sec).

Unsuccessful transfer is indicated by a series of rapid red flashes at the

end.

The overall time needed for the photo to be transferred from the

camera to the web server is about 20 seconds. In the case of a weak

signal, a delay may occur (due to the data being sent repetitively). Each

photo contains a date and time stamp for its creation (the value also

depends on the control panel settings). Time synchronization requires at

least 60 minutes to have elapsed from the moment of connecting the

module.

Technical specifications

Power supply 5 V DC (from the control panel)

Stand-by consumption approx. 2 mA

Environment according to EN 50131-1 Class II indoor-general

Operational temperature -10 to 40°C

EMC EN 55022, EN 50130-4

JABLOTRON ALARMS a.s. hereby declares that the

JA-80Q is in compliance with the essential requirements and

other relevant provisions of Directive 2004/108/EC. The original

of the conformity assessment can be found at

www.jablotron.com, Technical Support section

JABLOTRON ALARMS a.s. hereby declares that the product

complies with part 15 of the FCC rules. Operation is subject to

the following two conditions: 1. This device may not cause

harmful interference, and 2. This device must accept any

interference received, including interference that may cause

undesired operation.

CAUTION: Changes or modifications no expressly approved by

Jablotron could void the user’s authority to operate the

equipment.

Note: Although this product does not contain any harmful

materials we suggest you return the product to the dealer or

directly to the producer after use.

Produktspezifikationen

Marke:	Joblotron
Kategorie:	Sicherheitskamera
Modell:	JA-80Q

Brauchst du Hilfe?

Wenn Sie Hilfe mit Joblotron JA-80Q benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Sicherheitskamera Joblotron

Joblotron AN-80 Bedienungsanleitung

10 Juni 2023

Joblotron JA-80A Bedienungsanleitung

10 Juni 2023

Joblotron UC-222 Bedienungsanleitung

10 Juni 2023

Joblotron JS-20 Bedienungsanleitung

10 Juni 2023

Joblotron AC-83 Bedienungsanleitung

10 Juni 2023

Joblotron RC-22 Bedienungsanleitung

10 Juni 2023

Joblotron JA-60N Bedienungsanleitung

10 Juni 2023

Joblotron JA-83K Bedienungsanleitung

10 Juni 2023

Joblotron JA-65ST Bedienungsanleitung

10 Juni 2023

Joblotron PG-4M Bedienungsanleitung

10 Juni 2023

Bedienungsanleitung Sicherheitskamera

Neueste Bedienungsanleitung für -Kategorien-

Speco Technologies O2PTZ34D5W Bedienungsanleitung

14 August 2024

ZKTeco BL-34F26L Bedienungsanleitung

11 August 2024

Moxa VPort 26 Bedienungsanleitung

27 Juni 2024

Moxa VPort 36 Bedienungsanleitung

27 Juni 2024

Moxa VPort 16-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024

Moxa VPort 16-M12-CAM3L54160N Bedienungsanleitung

27 Juni 2024

Moxa VPort P06 Bedienungsanleitung

27 Juni 2024

Moxa VPORT P06-1MP-M12-CAM80 Bedienungsanleitung

27 Juni 2024

Moxa VPort 16-DO-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024

Moxa VPort 26A-1MP Bedienungsanleitung

27 Juni 2024