Joblotron JA-80H Bedienungsanleitung

Joblotron Sicherheitskamera JA-80H

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Joblotron JA-80H (1 Seiten) in der Kategorie Sicherheitskamera. Dieser Bedienungsanleitung war für 24 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF
Seite 1/1
The JA-80H outdoor keypad and RFID card reader MKM51101
1
The JA-80H outdoor keypad and RFID card reader
The JA-80H is a component of Jablotron’s Oasis
80 alarm system. It is designed to control access
(door lock) or to control a security system and
connects to the Oasis control panel via a WJ-80
interface.
Alternatively it can be connected to an AS-80 unit
as a part of a stand-alone access system.
The keypad sends data in Wiegand 26b format.
Installation
Installation shall only be undertaken by
technicians holding a certificate issued by an
authorized distributor. It is usually placed near an
entrance door (equipped with an electric lock). The
keypad can be used outdoors (conforms to IP-65).
1. Open the rear cover by unscrewing the screw
2. Prepare a hole in the wall for the keypad cable to
pass through, where the keypad will be located.
3. Attach the rear cover to the desired location (the
tamper spring must be properly pressed)
4. Pull the keypad cable through the wall hole and to the
interface unit’s box (WJ-80, AS-80)
5. Attach the keypad to the rear cover and secure it
using the screw
6. Connecting and setting up the keypad is described in
the WJ-80 or AS-80 manuals.
Cabling
wire signal
red +12V (power supply, 60mA)
green D0 (Wiegand 26b data output)
brown D1 (Wiegand 26b data output)
white TMP (normally closed tamper contact)
grey TMP (normally closed tamper contact)
yellow BZR (input controlling keypad sound – connecting to GND
generates a beep on the keypad)
blue GND (common ground)
pink not connected
Configuring the keypad for operation with the WJ-80
If the JA-80H keypad is connected to an Oasis control panel via a WJ-80
and it does not work as described in the manual, then it is not set to the
correct (factory default) operational mode. In such a case:
1. Switch the Oasis control panel to service mode
2. Disconnect the power from the control panel (mains and battery)
3. Disconnect the yellow and brown keypad wires from the terminals
and connect them together.
4. Power-up the control panel (keypad starts beeping)
5. Disconnect the yellow and brown wires (beeping will terminate)
6. On the JA-80H keypad, press button 4 (beeps once) and then button 3
(beeps several times)
7. Disconnect the power from the control panel, connect the yellow and brown
wires back up, power-up the control panel and check the proper functioning
of the JA-80H keypad
Technical specifications
Power supply 10 to 16V
Stand-by consumption typically 60mA
Housing IP65 (EN 60529)
Mechanical resistance IK08 (EN 50102)
Working environment class IV(EN 50131-1)
Operational temperature -25 to +60°C
RFID card Jablotron PC-01 or PC-02 (EM UNIQUE 125 kHz)
Dimensions 46 x 150.5 x 22.5mm
Length of the connection cable 1m
Complies with grade 2 (EN 50131-1, TS 50131-3)
Can be operated according to ERC REC 70-03
FCC ID VL6JA80H
Jablotron Ltd. hereby declares that the JA-80H is in compliance with the
essential requirements and other relevant provisions of Directive
1999/5/EC and complies with part 15 of the FCC rules. Operation is
subject to the following two conditions: 1. This device may not cause harmful
interference, and 2. This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION: Changes or modifications no expressly approved by Jablotron
could void the user´s authority to operate the equipment. The original of the
conformity assessment can be found at www.jablotron.com, Technical
Support section.
Note: Although this product does not contain any harmful
materials we suggest you return the product to the dealer or
directly to the producer after use.
TAMPER
22,545
151,5
87,5
cca 1 m
Note: The red LED is lit in Oasis normal operating mode. Pressing a button
is confirmed by a flash from the orange LED.
How to set up the JA-80H keypad for the AS-80 access system is described in the AS-80 manual.

Produktspezifikationen

Marke: Joblotron
Kategorie: Sicherheitskamera
Modell: JA-80H

Brauchst du Hilfe?

Wenn Sie Hilfe mit Joblotron JA-80H benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten


Bedienungsanleitung Sicherheitskamera Joblotron

Joblotron

Joblotron AN-80 Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron JA-80A Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron UC-222 Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron JS-20 Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron AC-83 Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron RC-22 Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron JA-60N Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron JA-83K Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron JA-65ST Bedienungsanleitung

10 Juni 2023
Joblotron

Joblotron PG-4M Bedienungsanleitung

10 Juni 2023

Bedienungsanleitung Sicherheitskamera

Neueste Bedienungsanleitung für -Kategorien-

Speco Technologies

Speco Technologies O2PTZ34D5W Bedienungsanleitung

14 August 2024
ZKTeco

ZKTeco BL-34F26L Bedienungsanleitung

11 August 2024
Moxa

Moxa VPort 26 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 36 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 16-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 16-M12-CAM3L54160N Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort P06 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPORT P06-1MP-M12-CAM80 Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 16-DO-M12-CAM3L5436N Bedienungsanleitung

27 Juni 2024
Moxa

Moxa VPort 26A-1MP Bedienungsanleitung

27 Juni 2024