Heatit Z-TRM3 Bedienungsanleitung

Heatit Thermostat Z-TRM3

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Heatit Z-TRM3 (8 Seiten) in der Kategorie Thermostat. Dieser Bedienungsanleitung war für 28 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

1. INTRODUCTION

Heatit Z-TRM3 is an electronic thermostat for electrical ﬂoor heating,

designed to be mounted in a standard ﬂush box. The thermostat has

a built-in Z-Wave chip that can be connected with Home Automation

systems. Heatit Z-TRM3 is equipped with a single-pole relay and ﬁts

into System 55 frames. The thermostat can withstand a load of max

16A /3600W at 230V. The thermostat may be used for water based

heating if the thermostat is linked to the Heatit Z-Water.

NB! If the sensor mode is changed to A or AF mode then a room

sensor compensation process will start, which limits maximum power

output to 75%. The thermostat adapts to the environment within a

few days. No internal sensor calibration should be performed during

the ﬁrst few days.

2. STATEMENT REGARDING PRODUCTS FROM MULTIPLE

MANUFACTURERS

Please read this before installation

This device may be used with all devices certiﬁed with the Z-Wave Plus™

certiﬁcate and should be compatible with such devices produced by

other manufacturers. Every primary controller is diﬀerent depending on

the manufacturer, their target consumer and intended use/application.

Please review the functionalities implemented by the primary controller

you intend to use with our Z-Wave Plus certiﬁed device to ensure that it

provides the necessary controls to take full advantage of our product’s

capabilities.

3. BEHAVIOR WITHIN THE Z-WAVE NETWORK

This device may be operated within any Z-Wave network with

Z-Wave-certiﬁed devices from other manufacturers. All non-battery

operated nodes within the network will act as repeaters regardless of

manufacturer to increase the reliability of the network. On delivery, the

device does not belong to any Z-Wave network. The device needs to be

added to an existing network to communicate with the other devices

within it. Devices may also be removed from a network. The add/remove

processes are initiated by the primary controller of the Z-Wave network.

The primary controller has a mode for adding or removing devices.

Please refer to your primary controller manual on how to set the

primary controller in add/remove mode. The device may only be

added or removed from the network if the primary controller is in

add/remove mode.

4. QUICK START

1. Switch oﬀ the mains supply (disable the fuse).

2. Open the wall switch box.

3. Connect wires according to the labeling described in

chapter 5 ”Installation”.

4. After verifying the connections, switch the mains supply back on.

5. Set the primary controller in add mode (security/non-security).

6. Press and hold the center button until “OFF” is shown on the

display (approx. 10 seconds).

7. Press down button until you reach “CON”, press and hold until the

display shows a rotating light pattern.

8. The thermostat will display “INC” when the thermostat is

successfully added.

NB! If adding/removing fails, Err (error) will appear.

HEATIT

Z-TRM3

Firmware 4.0

Installers manual

Ver 2020-C

TABLE OF CONTENTS

1 Introduction

2 Statement regarding products from multiple manufacturers

3 Behavior within the Z-Wave™ network

4. Quick Start

5. Installation

5.1 Controls

6. Add/Remove

6.1 Method 1 Standard (manual)

6.2 Method 2 SmartStart (automatic)

7 Factory Reset

7.1 Startup

8 Principles of regulation

9 Programming thermostat

10 Temperature shown in display

11 Standby and main screen

12 Choice of sensor

13 Selecting the right Ohm value for your external ﬂoor sensor

14 Calibration

15 Brightness

16 Hysteresis (dIF)

17 Min/Max temperature settings

18 Fast functions from Standby / Main Screen

18.1 Display on/oﬀ - don/doF

18.2 Childlock - Lock

19 Error codes

20 Z-Wave QR-code / DSK

21 Security

22 Node Information Frame

23 Associations

24 Conﬁguration parameters

25 Command class speciﬁcations

Product information

01.03.20

51,1mm

15,6mm21,3mm

49,5mm

5. INSTALLATION

Installation must be done by a qualiﬁed electrician in accordance with

the National Building codes. Before installation, disconnect any power to

the thermostat mains. During installation of the thermostat, power to the

thermostat must be disconnected AT ALL TIMES!

5.1 CONTROLS

Use e.g. a small slotted screwdriver. Start by carefully removing the front

cover by pushing the release springs. The front cover and the frame may

now be removed.

Connect the wires to the thermostat terminals:

Use 1,5mm² or 2,5mm² according to load.

HEATING (N) Heating cable connection (Neutral)

N Power connection (Neutral) 230V

L Power connection (Live) 230V

HEATING (L) Heating cable connection

FLOOR SENSOR NTC type (10, 12, 15, 22, 33 or 47kΩ)

Default 10kΩ

EXTERNAL SENSOR NTC type (10, 12, 15, 22, 33 or 47kΩ)

Default 10kΩ

Next, position the thermostat and mount it into the wall ﬂush box

using 2-4 screws. Position the frame over the ﬂush box, then position

and carefully press the front cover until it snaps in place. Check that

the front cover has snapped in place properly on both sides. The front

cover should now ﬁt ﬁrmly on all sides. In order to read the Power

Made in EU

16A 230V~

50/60HZ

IP21

TF 058

HEATING L

HEATING N

FLOOR

SENSOR

EXTERNAL

SENSOR

Z-T RM3

Release spring

58,8mm

87mm

1: Left 2: Center 3: Right

MULT IREG® Z-WAVE

Metering, the load needs to be connected to both heating L + N.

NOTE! The top cover has to be installed when the thermostat is

connected to the main power source. The thermostat is not a SELV

product. All voltage parts must be considered to be 230VAC.

6. ADD/REMOVE

The primary controller/gateway has a mode for adding or removing

devices. Please refer to your primary controller manual on how to set the

primary controller in add/remove mode. The device may only be added

or removed from the network if the primary controller is in add/remove

mode. When the device is removed from the network, it will NOT revert to

factory settings.

There are two ways to add the Heatit Z-TRM3 to a Z-Wave network.

6.1 METHOD 1: STANDARD (MANUAL)

1. Press Center (conﬁrm) for 10 seconds. The display will show OFF.

2. Press Right (down) 5 times until you see Con on the display.

3. Start the add/remove device process in your primary controller.

4. Start the add/remove mode in the Heatit Z-TRM3 by pressing

Center (conﬁrm) for approximately 2 seconds.

Adding/removing mode is indicated on the display by rotating

LED segments on the display. This lasts until the timeout occurs

after 90 seconds, or until the module has been added/removed

in the network. Conﬁrmation will show Inc/EcL on the display. Exit

programming mode by choosing ESC in the menu. Your thermostat

is now ready for use with default settings.

NB! When the thermostat is removed from the gateway, the

parameters are not reset. To reset the parameters, see Chapter 7:

”Factory reset”. If adding/removing fails, Err (error) will appear.

Please perform a ”remove device” process and try again. If Err displays

again, please see Chapter 7: “Factory reset”.

6.2 METHOD 2: SMARTSTART (AUTOMATIC)

SmartStart enabled products can be added into a Z-Wave network

by scanning the Z-Wave QR-Code present on the product with a

controller providing SmartStart inclusion. No further action is required

and the SmartStart product will be added automatically within 10

minutes of being switched on in the network vicinity.

The Z-Wave QR-Code locations may be found in Chapter 20

”Z-Wave QR-Code/DSK”.

7. FACTORY RESET

By pressing buttons Right and Center (down and conﬁrm) for 20 seconds,

the thermostat will perform a complete factory reset.

NB! Please use this procedure only when the primary controller/ gateway

is missing or otherwise inoperable.

The device will display rES for 10 seconds while performing a factory reset.

When rES no longer is displayed, the thermostat has been reset.

7.1 STARTUP

AFTER POWERING UP THE THERMOSTAT FOR THE FIRST TIME, ALL

PARAMETERS WILL HAVE DEFAULT SETTINGS.

PRINCIPLES OF REGULA

PRINCIPLES OF REGULATION

TION

TION8. PRINCIPLES OF REGULATION

Using Floor / External sensor (F, A2 or A2F-Mode)

The thermostat uses temperature readings retrieved from the internal

sensor or external wired sensor to regulate heating. When you have

chosen a setpoint temperature, the thermostat will use an internal

hysteresis to regulate the temperature. This hysteresis is adjustable.

See Chapter 5 “Installation”.

Using Internal sensor (A-mode/AF mode)

If you have a set point of 20°C, the thermostat will use the full power until

the temperature is 19°C. The thermostat will then begin to regulate the

output from 19°C with a 75% duty cycle until it reaches 19,25°C. When

the temperature has reached 19.5°C the thermostat will use a 50% duty

cycle, until it reaches 20°C, then the thermostat turns oﬀ and repeats the

process. For example, at a 75% duty cycle it will turn ON for a total of 90

minutes and OFF for 30 minutes.

50% duty cycle

75% duty cycle

20 min.

30 min. 30 min. 30 min.

20 min.

2 hrs.

20 min.

9. PROGRAMMING THE THERMOSTAT

To activate the programming mode, press Center (conﬁrm) for 10

seconds. The display will show OFF. You are now in programming

mode. To scroll up and down in the menu, use buttons 1 and 3 (left

and right) to navigate. To enter the submenu, press Center (conﬁrm).

Always conﬁrm your setting by pressing Center (conﬁrm) for

2 seconds. Sto will appear to indicate saved settings.

10. TEMPERATURE SHOWN IN DISPLAY

By default, the temperature shown on the display is the setpoint. This may

be altered with parameter 13: “Temperature display”. You may calibrate

the sensor values ±4 degrees using parameters 10 to 12.

11. STANDBY AND MAIN SCREEN

When the thermostat remains untouched for a while, it will automatically

revert to the standby screen. The standby screen will by default show

the setpoint temperature. By pressing any button once, you will see the

measured temperature. By pressing the left or right (up or down) button

one more time, you will change the setpoint.

Menu structure

OFF Turns the thermostat oﬀ.

Sensors:

CHOICE OF SENSORS

F Depending on your choice of sensors, the menu

will change.

SEn Select the right Ohm value for your external/ﬂoor sensor.

NTC type (10, 12, 15, 22, 33 or 47kΩ). Default 10kΩ.

CAE Calibration for external sensor.

CAF Calibration for ﬂoor sensor.

CAr Calibration for internal sensor.

br1 The display brightness may be adjusted in this menu.

Con Activation of inclusion/exclusion mode.

dIF Hysteresis.

ALo Setting lowest allowed temperature (limitation).

(Air sensor)

AHI Setting highest allowed temperature (limitation).

(Air sensor)

Flo Setting lowest allowed temperature (limitation).

(Floor sensor)

FHI Setting highest allowed temperature (limitation).

(Floor sensor)

A2L Setting lowest allowed temperature (limitation).

(A2 air sensor)

A2H Setting highest allowed temperature (limitation).

(A2 air sensor)

ESC Escape – exit programming menu.

12. CHOICE OF SENSOR

The thermostat has a range of choices when it comes to sensors.

To access the menu, press Center (conﬁrm) for 10 seconds, then press

Right (down) once. An A will appear on the display. Then press Center

(conﬁrm) again and choose modes while moving up and down with

buttons Left or Right:

F Floor sensor

A Internal sensor

AF nternal sensor + Floor sensor

A2 External room sensor

A2F External room sensor + Floor sensor

When you have chosen sensor mode, press the Center (conﬁrm) button.

If you choose F without having a ﬂoor sensor connected, Er4 will be

shown in the display. If you choose A2 or A2F and there is no external

sensor installed, Er5 will be displayed on the screen.

NOTE: Wooden ﬂoors require that a ﬂoor sensor is connected in order

to limit the ﬂoor temperature to a maximum of 27°C (in accordance with

speciﬁcations from most wooden ﬂoor manufacturers).

When using the thermostat is used in (AF or A2F) the ﬂoor limiter FHI is

automaticly set to 27°C. When using any other sensor type (A, F or A2F)

the max temperatures is default 5°C minum and 40°C maximum.

13. SELECTING THE RIGHT OHM VALUE FOR YOUR EXTERNAL

FLOOR SENSOR

The following values are available: NTC type (10, 12, 15, 22, 33 or 47kΩ).

Default 10kΩ. Conﬁrm with the Center (conﬁrm) button. You can not

combine two types of NTC sensors.

Produktspezifikationen

Marke:	Heatit
Kategorie:	Thermostat
Modell:	Z-TRM3
Produktfarbe:	Schwarz
Internationale Schutzart (IP-Code):	IP21
Energiequelle:	AC
AC Eingangsspannung:	230 V
AC Eingangsfrequenz:	50 - 60 Hz
Kindersicherung:	Ja
Schnittstelle:	Z-Wave
Nachhaltigkeitskonformität:	Ja
Nachhaltigkeitszertifikate:	CE, RoHS
Intelligentes Thermostat:	Ja
Maßeinheit:	°C
Temperatursensor:	Ja
Frequenz:	868.4 MHz
Geeignet für Nassbereiche:	Nein