Heatit HEAE5430499 Bedienungsanleitung

Heatit Thermostat HEAE5430499

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Heatit HEAE5430499 (4 Seiten) in der Kategorie Thermostat. Dieser Bedienungsanleitung war für 6 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/4

Ver 2016-B

IMPORTANT!

PLEASE READ THIS BEFORE INSTALLATION.

This thermostat is tested and certiﬁed by Pepper One Gmbh

according to the requirements put forward by the Z-Wave

Alliance. This is a Z-wave Plus product with the 500 series chip.

If the product does not work with your gateway, then the

gateway manufacturer has not made an integration or

implemented such a thermostat with their gateway.

We do not give any guarantee towards integration.

PRINCIPLES FOR REGULATION

The Heatit Z-Wave thermostat is designed for controlling

electrical heating cables and electrical radiators/convectors.

The thermostat has 2 internal temperature sensors and has

3 algorithms for temperature compensation. After you have

set the temperature, the thermostat will use a hysteresis to

regulate the temperature. The hysteresis is adjustable.

TEMPERATURE SHOWN IN DISPLAY

The temperature shown in the display is the actual temperature

for ﬂoor sensor and the external room sensor. You are able to

calibrate the sensor values.

When using the internal room sensor, the temperature shown

is the set point. When using the internal sensor, the thermostat

can seem somewhat inaccurate. This is due to heat generation

inside the thermostat, draft and other external inﬂuences.

If the thermostat is to be used with waterbased heating systems,

you have to use an external sensor.

SETUP

This manual describes the most essential functions and

technical speciﬁcations of the thermostat. These instructions

help the user to control the thermostat, and the electrician

to install and setup the thermostat.

INSTALLATION

Installation must be done by a qualiﬁed electrical installer in

accordance with the National Building codes. Before installation,

disconnect any power to the thermostat’s mains. During

installation of the thermostat, power to the thermostat must

be disconnected AT ALL TIMES!

Use e.g. a small slotted screwdriver. Start by carefully removing

the front cover by pushing the release springs. The front cover

and the frame can now be removed.

Now connect the wires to the thermostat’s terminals:

HEATING (N) Heating cable connection (Neutral)

N Power connection (Neutral) 230V

L Power connection (Live) 230V

HEATING (L) Heating cable connection (Live)

PILOT Pilot signal (ECO temp) 230V

FLOOR SENSOR NTC type (10, 12, 15, 22, 33 or 47kΩ).

Default 10kΩ.

EXTERNAL SENSOR NTC type (10, 12, 15, 22, 33 or 47kΩ).

Default 10kΩ.

Next, position the thermostat and fasten it onto the wall’s

mounting box using 2-4 screws. Position the frame, then

position and carefully press the front cover until it snaps in

place. Check that the front cover has snapped in place properly

on both left and right side. The front cover should now be ﬁrmly

ﬁxed on all sides.

STARTUP

AFTER CONNECTING THE POWER TO THE THERMOSTAT FOR THE

FIRST TIME, ALL PARAMETERS WILL HAVE DEFAULT SETTINGS.

2 yr

HEATIT Z-WAVE

Installers manual

Firmware 1.8

01.06.2016

Release spring

1: Left 3: Right2: Center

87 mm

58,8 mm

HEAT ING L

HEAT ING N

PILOT WIRE

FLOOR

SENSOR

EXT ERNAL

SENSOR

Made in EU

TF 021

21,3 mm

51,1 mm

87 mm

58,8 mm

29,9 mm

CONTROL

The thermostat is controlled by three touch sensitive capacitive

buttons.

You only need to touch lightly to activate the buttons.

1: Left (Up)

2: Center (Conﬁrm)

3: Right (Down)

INCLUSION/EXCLUSION

To include the thermostat to your home automation gateway,

press Center (conﬁrm) for 10 seconds.

The display will show OFF. Press Right (down) 4 times till you

see Con in the display. Now start add device in your home

automation software. Start inclusion mode by pressing Center

(conﬁrm) for approximately 2 seconds. The inclusion/exclusion

icon will appear in the display. Conﬁrmation will show Inc/EcL

in the display. If inclusion fails, Err (error) will appear.

Leave programming mode by choosing ESC in menu.

Your thermostat is ready for use with default settings.

PROGRAMMING YOUR THERMOSTAT

To activate the programming mode, press Center (conﬁrm)

for 10 seconds. Now the display will show OFF.

Now you are in programming mode. To scroll up and down

in the menu use button 1 and 3 (left and right) to navigate.

To enter submenu press Center (conﬁrm). Always conﬁrm

your setting by pressing Center (conﬁrm) for 2 seconds.

Menu:

OFF Turns the thermostat oﬀ.

Sensors:

F Floor sensor

A Internal room sensor

AF Internal room + Floor sensor

A2 External room sensor

P Power regulator

FP Floor sensor + Power regulator

A2F External room sensor + Floor sensor

Depending on your choice of sensors, the menu will change.

SEn Select the right Ohm value for your external/ﬂoor sensor.

NTC type (10, 12, 15, 22, 33 or 47kΩ). Default 10kΩ.

CAE Calibration for external sensor.

CAF Calibration for ﬂoor sensor.

CAR Calibration for room sensor.

br1 Brightness of display can be adjusted in this menu.

Con Activation of inclusion/exclusion mode.

diF Hysteresis

ALo Setting lowest allowed temperature (limitation).

(Airsensor)

AHI Setting highest allowed temperature (limitation).

(Airsensor)

FLO Setting lowest allowed temperature (limitation).

(Floor sensor)

FHI Setting highest allowed temperature (limitation).

(Floor sensor)

HEA Switch between heating and cooling function.

ESC Escape – exit programming menu.

PRODUCT INFO Heatit Z-Wave

FEATURES

• Floor sensor

• External room sensor

• Internal room sensor

• Temperature limiter

• Power regulator

• Z-Wave Plus, 500 series

• Weekly program via gateway

• Setback mode via

gateway or pilot wire

• LED-diode

• Can be used in connection

with diﬀerent NTC-sensors

• Lock mode/child lock

• Backlight

• Calibration

• 8 associations

TECHNICAL DATA

Protocol Z-Wave Plus, 868,4 MHz

Rated voltage 230V 50/60Hz

Max load 3600W (resistive load)

750W self-limiting heating cable

Max current 16A

Power consumption 1,5W

Power regulator Time cycle 0-30 min

Min/max installation temp. -20°C to 40°C

Min/max operating temp. 5°C to 40°C

Temperature intervals Floor sensor 5°C to 40°C

External room sensor 5°C to 40°C

Hysteresis 0,3°C to 3,0°C (default 0,5°C)

Sensor values 0°C 29,1 kOhm

10°C 18,6 kOhm

15°C 15,1 kOhm

20°C 12,2 kOhm

25°C 10,0 kOhm

Switch Single-pole switch

IP class IP21

TERMINAL

Use 1,5 mm² or 2,5 mm² according to load.

INCLUDED IN PACKAGE

Floor sensor 3 meters, Art. no. 5430109

WARRANTY

2 years

The thermostat is designed for electrical heating.

ART. NO. PRODUCT COLOR

5430499 Heatit Z-Wave thermostat 3600W 16A White RAL 9003

5430498 Heatit Z-Wave thermostat 3600W 16A Black RAL 9011

5430311 Frame for Heatit White RAL 9003

5430312 Frame for Heatit Black RAL 9011

5430497 Cable for software update on thermostat

5430108 Floor sensor Ø3mm 6m NTC 10 kOhm

5430109 Floor sensor Ø4mm 3m NTC 10 kOhm

5430128 External room sensor, glass front NTC 10 kOhm

5430471 External enclosed sensor IP 20/54

CHOICE OF SENSOR

The thermostat has a range of choices when it comes to

sensors. To get to the menu you have to press Center (conﬁrm)

for 10 seconds, then press Right (down) once and an A shows

in the display. Then press Center (conﬁrm) again and you can

choose one of these modes, while moving up and down with

buttons Left or Right.

F Floor sensor

A Internal room sensor

AF Internal room sensor + Floor sensor

A2 External room sensor

P Power regulator

FP Floor sensor + Power regulator

A2F External room sensor + Floor sensor

When you have decided on the sensor mode you want to use,

press the Center (conﬁrm) button. If you choose F or AF without

having a ﬂoor sensor connected, Er4 will be shown in the

display. If you choose A2 or A2F and there is no external

sensor installed, Er5 will be displayed on the screen.

NOTE: Wooden ﬂoors require that a ﬂoor sensor is connected

in order to limit the ﬂoor temperature to a maximum of 27°C

(in accordance with speciﬁcations from most wooden ﬂoor

manufacturers).

SELECT THE RIGHT OHM VALUE FOR YOUR EXTERNAL/

FLOOR SENSOR

The following values are available: NTC type (10, 12, 15, 22, 33 or

47kΩ). Default 10kΩ. The function is only active when an external

sensor is connected. Conﬁrm with Center (conﬁrm) button.

CALIBRATION

In this mode you are able to adjust the displayed temperature.

If the thermostat of some reason (or sensor) is not calibrated

properly you are able to make minor changes to the

temperature. You are able to raise/lower the set point by

up to 4°C. Conﬁrm with Center (conﬁrm) button.

This function is only available for the ﬂoor sensor and external

room sensor. When calibrating the room sensor, only the

setpoint is changed. The display will not change.

BRIGHTNESS

Use Left and Right (up and down) button to adjust the

brightness between 0-9. Conﬁrm with Center (conﬁrm) button.

INCLUSION/EXCLUSION

To include the thermostat to your home automation gateway,

press Center (conﬁrm) button for 10 seconds. The display

will show OFF. Press Right (down) 4 times till you see Con in

the display. Now start add device in your home automation

software. Start inclusion mode by pressing Center (conﬁrm)

button for approximately 2 seconds. The inclusion/exclusion

icon will appear in the display. Conﬁrmation will show Inc/EcL

in the display. If inclusion fails, Err (error) will appear.

HYSTERESIS (DIF)

In this mode you are able to make changes to the hysteresis in

the thermostat. This means that you can changes the hysteresis

from 0.2°C up to max 3.0°C. Conﬁrm with Center (conﬁrm)

button. Default setting is 0.5°C. When using a waterbased

heating, the recommended hysteresis is a minimum of 1.0°C.

MIN/MAX TEMPERATURE SETTINGS

FLO Min Floor temperature

FHI Max Floor temperature

ALO Min Air/room temperature

AHI Max Air/room temperature

PLO Min temperature in Power Reg Mode

Conﬁrm with Center (conﬁrm)

HEA Choose whether the thermostat is to be used for heating

or cooling.

ESC Leaving programming mode. Conﬁrm with Center

(conﬁrm) button.

STANDBY AND MAIN SCREEN

When the thermostat remains untouched for a while, it will

automatically go to standby screen. Standby screen shows the

temperature in the room or ﬂoor if the thermostat is connected

to external sensors. By pressing Left or Right (up or down)

button the setpoint will be shown in the display. If the internal

room sensor is used, the thermostat display shows the setpoint.

DISPLAY ON/OFF - DON/DOF

Activate by pressing Left and Center (up and conﬁrm) button for

10 seconds. The display light is temporarily activated if one of

the buttons is pushed.

In case doF is activated, the screen will be blank (can be used if

installed where people are sensitive to the light of the display).

A very nice feature when used in a bedroom. When touching

the display, the screen lights up.

CHILDLOCK - LOC

By pressing Left and Right (up and down) buttons for 10

seconds, child lock will be activated and no changes can be

made. Trying to make changes causes the LOC text to appear

in the display. Child lock is deactivated by pressing Left and

Right (up and down) buttons for 10 seconds. OPn will appear

in the display.

FACTORY RESET - RES

By pressing buttons Right and Center (down and conﬁrm) for 20

seconds, the thermostat will perform a complete factory reset.

NB! Please use this procedure only when the primary controller/

gateway is missing or otherwise inoperable.

CO/ECO MODE

The thermostat has 2 main programs, CO – comfort mode and

ECO - economy mode. When Center (conﬁrm) button is pushed

for 2 seconds you switch between the 2 modes. You would

normally have 2 diﬀerent set-points for the diﬀerent modes.

Produktspezifikationen

Marke:	Heatit
Kategorie:	Thermostat
Modell:	HEAE5430499

Brauchst du Hilfe?

Wenn Sie Hilfe mit Heatit HEAE5430499 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Thermostat Heatit

Heatit PRO Bedienungsanleitung

24 September 2024

Heatit MULTIREG6 Bedienungsanleitung

24 September 2024

Heatit WiFi6 Bedienungsanleitung

5 September 2024

Heatit Z-TRM6 DC Bedienungsanleitung

5 September 2024

Heatit WiFi Bedienungsanleitung

5 September 2024

Heatit External Room Sensor Bedienungsanleitung

5 September 2024

Heatit HEAE5430499 Bedienungsanleitung

22 Juli 2024

Heatit Z-TRM3 Bedienungsanleitung

13 Januar 2024

Heatit Z-Wave Plus Bedienungsanleitung

18 November 2023

Heatit Z-Wave Bedienungsanleitung

20 Juni 2023

Bedienungsanleitung Thermostat

Neueste Bedienungsanleitung für -Kategorien-

Siemens RDG100T Bedienungsanleitung

16 Oktober 2024

Siemens N2264 Bedienungsanleitung

7 Oktober 2024

Honeywell Round on-off T87G1006 Bedienungsanleitung

5 Oktober 2024

Theben RAM 811 Top - 811 9 901 Bedienungsanleitung

5 Oktober 2024

Siemens DESIGO RXA Bedienungsanleitung

5 Oktober 2024

Drayton RTS10 Bedienungsanleitung

5 Oktober 2024

Honeywell Day Night Round T8700A Bedienungsanleitung

4 Oktober 2024

Busch-Jaeger 1097 U Bedienungsanleitung

3 Oktober 2024

Eberle RTR-E 3545 Bedienungsanleitung

2 Oktober 2024

Eberle RTR 9164 Bedienungsanleitung

2 Oktober 2024