First Alert SMCO100V-AC Bedienungsanleitung

First Alert Rauchmelder SMCO100V-AC

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für First Alert SMCO100V-AC (2 Seiten) in der Kategorie Rauchmelder. Dieser Bedienungsanleitung war für 24 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/2

USER’S MANUAL

SMOKE & CARBON MONOXIDE ALARM

AC POWERED WITH VOICE & LOCATION

Model SMCO100V-AC

IMPORTANT! PLEASE READ CAREFULLY AND SAVE.

The warnings/limitations card and manual contains important

information about your Smoke Alarm’s operation. If you are

installing this Alarm for use by others, you must leave this

manual—or a copy of it—with the end user.

Para el manual del usuario en español, por favor

visite rstalert.com

DANGER!

ELECTRICAL SHOCK HAZARD. Turn off the power to the area where the Smoke Alarm is

installed before removing it from the mounting bracket. Failure to turn off the power

rst may result in serious electrical shock, injury or death.

! WARNING!

• This unit will not alert hearing impaired residents.

• It is recommended that you install special units which use devices like ashing strobe

lights to alert hearing impaired residents.

• Installation of this unit must conform to the electrical codes in your area; Articles 210

and 300.3 (B) of NFPA 70 (NEC), NFPA 72, NFPA 101; SBC (SBCCI); UBC (ICBO); NBC

(BOCA); OTFDC (CABO), and any other local or building codes that may apply. Wiring and

installation must be performed by a licensed electrician. Failure to follow these guidelines

may result in injury or property damage.

• This unit must be powered by a 24-hour, 120VAC pure sine wave 60Hz circuit. Be sure the

circuit cannot be turned off by a switch, dimmer, or ground fault circuit interrupter. Failure

to connect this unit to a 24-hour circuit may prevent it from providing constant protection.

• This Alarm must have AC or battery power to operate.

• If the AC power fails, battery back-up will allow the alarm to sound for at least 4 minutes.

If AC power fails and the battery is weak, protection should last for at least 7 days.

• If AC power fails and the battery is dead or missing, the alarm cannot operate.

• Never disconnect the power from an AC powered unit to stop an unwanted alarm. Doing

so will disable the unit and remove your protection. In the case of a true unwanted alarm

open a window or fan the smoke away from the unit.

• The alarm will reset automatically when it returns to normal operation. Never remove

the batteries from a battery operated unit to stop an unwanted alarm (caused by cooking

smoke, etc.). Instead open a window or fan the smoke away from the unit. The alarm will

reset automatically.

! CAUTION!

• Connect this unit ONLY to other compatible units. See “How To Install This Smoke Alarm”

for details. Do not connect it to any other type of alarm or auxiliary device.

• Connecting anything else to this unit may damage it or prevent it from operating properly.

• This Smoke/CO Alarm has a battery drawer which resists closing unless a battery is

installed. This warns you the unit will not operate under DC power without a battery.

• Do not stand too close to the unit when the alarm is sounding. It is loud to wake you in an

emergency. Exposure to the horn at close range may harm your hearing.

• Do not paint over the unit. Paint may clog the openings to the sensing chambers and

prevent the unit from operating properly.

01 INTRODUCTION

Thank you for choosing First Alert

for your Smoke and Carbon Monoxide Alarm needs. You have

purchased a state-of-the-art Smoke & Carbon Monoxide Alarm designed to help provide you with early

warning of a smoke and/or carbon monoxide danger. Please take the time to read this manual and

make the Smoke & Carbon Monoxide Alarm an integral part of your family’s safety plan.

BASIC SAFETY INFORMATION

IMPORTANT!

• Dangers, Warnings, and Cautions alert you to important operating instructions or to potentially

hazardous situations. Pay special attention to these items.

• This smoke and co alarm is approved for use in single-family residences. It is designed for NOT

marine or RV use.

! CAUTION!

• The Smoke Alarm will only indicate the presence of smoke that reaches the sensor.

• The Smoke Alarm is not designed to sense gas, heat or ames.

! WARNING!

• This Smoke Alarm cannot operate without working batteries. Removing the batteries for any

reason, or failing to replace the batteries at the end of their service life, removes your protection.

• ignore any alarm. See “If Your Smoke Alarm Sounds” for more information on how to NEVER

respond to an alarm. Failure to respond can result in injury or death.

• The Silence Features are for your convenience only and will not correct a problem. See “Using the

Silence Features” for details. Always check your home for a potential problem after any alarm.

Failure to do so can result in injury or death.

• Test this Smoke Alarm once a week. If the alarm ever fails to test correctly, have it replaced

immediately! If the alarm is not working properly, it cannot alert you to a problem.

02 ABOUT SMOKE ALARMS

TYPES OF ALARMS

All these Smoke Alarms are designed to provide early warning of res if located, installed and cared

for as described in the user’s manual, and if smoke reaches the Alarm. If you are unsure which type of

Smoke Alarm to install, refer the National Fire Protection Association (NFPA) Standard 72 (National Fire

Alarm and Signaling Code) and NFPA 101 (Life Safety Code). National Fire Protection Association, One

Batterymarch Park, Quincy, MA 02269-9101. Local building codes may also require specic units in

new construction or in different areas of the home.

Battery (DC) operated Smoke Alarms: Provide protection even when electricity fails, provided the

batteries are fresh and correctly installed. Units are easy to install, and do not require professional

installation. However, they do not provide interconnected functionality.

AC powered Smoke Alarms: Can be interconnected so if one unit senses smoke, all units Alarm.

They do not operate if electricity fails. will operate if electricity fails, AC with battery (DC) back-up:

provided the batteries are fresh and correctly installed. AC and AC/DC units must be installed by a

qualied electrician.

Smoke Alarms for solar or wind energy users and battery backup power systems: AC powered

Smoke Alarms should only be operated with true or pure sine wave inverters. Operating this Alarm

with most battery-powered UPS (uninterruptible power supply) products or square wave or “quasi sine

wave” inverters . If you are not sure about your inverter or UPS type, please will damage the Alarm

consult with the manufacturer to verify.

Smoke Alarms for the hearing impaired: Special purpose Smoke Alarms should be installed

for the hearing impaired. They include a visual Alarm and an audible Alarm horn, and meet the

requirements of the Americans With Disabilities Act. Can be interconnected so if one unit senses

smoke, all units Alarm.

Smoke Alarms are not to be used with detector guards unless the combination has been evaluated

and found suitable for that purpose.

All First Alert

Smoke Alarms conform to regulatory requirements, including UL217 and are

designed to detect particles of combustion. Smoke particles of varying number and size are

produced in all res.

Ionization technology is generally more sensitive than photoelectric technology at

detecting small particles, which tend to be produced in greater amounts by aming res,

which consume combustible materials rapidly and spread quickly. Sources of these res

may include paper burning in a wastebasket, or a grease re in the kitchen.

Photoelectric technology is generally more sensitive than ionization technology at

detecting large particles, which tend to be produced in greater amounts by smoldering

res, which may smolder for hours before bursting into ame. Sources of these res may

include cigarettes burning in couches or bedding.

For maximum protection, use both types of Smoke Alarms on each level and in every

bedroom of your home.

03 INSTALLATION

WHERE TO INSTALL THIS ALARM

Minimum coverage for Smoke Alarms, as recommended by the National Fire Protection Association

(NFPA), is one Smoke Alarm on every oor, in every sleeping area, and in every bedroom (See

“Regulatory Information For Smoke Alarms” for details on the NFPA recommendations).

For CO Alarms, the National Fire Protection Association (NFPA) recommends that a CO Alarm

should be centrally located outside of each separate sleeping area in the immediate vicinity of the

bedrooms. For added protection, install additional CO Alarms in each separate bedroom, and on every

level of your home.

NOTE: For added protection, install an additional Smoke/CO Alarm at least 15 feet (4.6 meters) away

from the furnace or fuel burning heat source where possible. In smaller homes or in manufactured

homes where this distance cannot be maintained, install the Alarm as far away as possible from the

furnace or other fuel burning source. Installing the Alarm closer than 15 feet (4.6 meters) will not harm

the Alarm, but may increase the frequency of unwanted alarms.

IN GENERAL, INSTALL COMBINATION SMOKE AND CARBON MONOXIDE ALARMS:

• On every level of your home, including nished attics and basements.

• Inside every bedroom, especially if people sleep with the door partly or completely closed.

• In the hall near every sleeping area. If your home has multiple sleeping areas, install a unit in each.

If a hall is more than 40 feet (12 meters) long, install a unit at each end.

• At the top of rst-to-second oor stairs and at the bottom of the basement stairs.

• For additional coverage, install Alarms in all rooms, halls, and storage areas, where temperatures

normally remain between 40˚ F and 100˚ F (4.4˚ C and 37.8˚ C).

RECOMMENDED PLACEMENT:

Smoke Alarm

One on every level and

in every bedroom

Carbon Monoxide Alarm

One on every level and

in every bedroom

Fire Extinguisher

One on every level, plus

kitchen and garage

• When installing on the ceiling, place the Alarm as close to the center as possible.

• When installing on the wall, the top edge of Smoke Alarms should be placed between 4 inches

(102 mm) and 12 inches (305 mm) from the wall/ceiling line.

• In either case, install at least 4 inches (102 mm) from where the wall and ceiling meet. See

“Avoiding Dead Air Spaces” for more information.

NOTE: For any location, make sure no door or other obstruction could keep carbon monoxide or smoke

from reaching the Alarm.

WHERE NOT TO INSTALL THIS ALARM

FOR BEST PERFORMANCE, IT IS RECOMMENDED YOU AVOID INSTALLING SMOKE/CO ALARMS

IN THESE AREAS:

• In garages, furnace rooms, crawl spaces and unnished attics. Avoid extremely dusty, dirty

or greasy areas.

• Where combustion particles are produced. Combustion particles form when something burns.

Areas to avoid include poorly ventilated kitchens, garages, and furnace rooms. Keep units at

least 20 feet (6 meters) from the sources of combustion particles (stove, furnace, water heater,

space heater) if possible. In areas where a 20-foot (6 meter) distance is not possible – in modular,

mobile, or smaller homes, for example – it is recommended the Smoke Alarm be placed as far

from these fuel-burning sources as possible. The placement recommendations are intended

to keep these Alarms at a reasonable distance from a fuel-burning source, and thus reduce

“unwanted” Alarms. Unwanted Alarms can occur if a Smoke Alarm is placed directly next to a

fuel-burning source. Ventilate these areas as much as possible.

• Within 5 feet (1.5 meters) of any cooking appliance. In air streams near kitchens. Air currents can

draw cooking smoke into the smoke sensor and cause unwanted Alarms.

• In extremely humid areas. This Alarm should be at least 10 feet (3 meters) from a shower, sauna,

humidier, vaporizer, dishwasher, laundry room, utility room, or other source of high humidity.

• In direct sunlight.

• In turbulent air, like near ceiling fans or open windows. Blowing air may prevent smoke from

reaching the sensors.

• In areas where temperature is colder than 40˚ F (4.4˚ C) or hotter than 100˚F (37.8˚ C). These

areas include non air-conditioned crawl spaces, unnished attics, uninsulated or poorly insulated

ceilings, porches, and garages.

• In insect infested areas. Insects can clog the openings to the sensing chamber.

• Less than 12 inches (305 mm) away from uorescent lights. Electrical “noise” can interfere

with the sensor.

• In “dead air” spaces.

AVOIDING DEAD AIR SPACES

“Dead air” spaces may prevent smoke from reaching the Smoke Alarm. To avoid dead air spaces,

follow installation recommendations below.

On ceilings, install Smoke Alarms as close to the center of the ceiling as possible. If this is not

possible, install the Smoke Alarm at least 4 inches (102 mm) from the wall or corner.

For wall mounting (if allowed by building codes), the top edge of Smoke Alarms should be placed

between 4 inches (102 mm) and 12 inches (305 mm) from the wall/ceiling line, below typical

“dead air” spaces.

On a peaked, gabled, or cathedral ceiling, install the rst Smoke Alarm within 3 feet (0.9 meters) of

the peak of the ceiling, measured horizontally. Additional Smoke Alarms may be required depending

on the length, angle, etc. of the ceiling’s slope. Refer to NFPA 72 for details on requirements for sloped

or peaked ceilings.

HOW TO INSTALL THIS ALARM

IMPORTANT!

This Smoke/CO Alarm is designed to be mounted on any standard wiring junction box up to a 4-inch

(10 cm) size, on either the ceiling or wall (if allowed by local codes). Read “Where to Install This Alarm”

and “Where This Alarm Should Not Be Installed” before you begin installation.

Tools you will need: needle-nose pliers or utility knife, standard athead screwdriver, wire strippers

! WARNING!

Make sure the Alarm is not receiving excessively noisy power. Examples of noisy power could

be major appliances on the same circuit, power from a generator or solar power, light dimmer

on the same circuit or mounted near uorescent lighting. Excessively noisy power may cause

damage to your Alarm.

THE PARTS OF THIS ALARM

The Mounting Bracket: To remove the mounting

bracket from the Alarm base, hold the Alarm

base rmly and twist the mounting bracket

counterclockwise. The mounting bracket installs

onto the junction box. It has a variety of screw slots

to t most boxes.

The Power Connector: The power connector plugs

into a power input block on the Alarm. It supplies

the unit with AC power.

• The black wire is “hot.”

• The white wire is neutral.

• The orange wire is used for interconnect.

If you need to remove the power connector, turn rst. Insert a at screwdriver blade POWER OFF

between the power connector and the security tab inside the power input block. Gently pry back the

tab and pull the connector free.

THE PARTS OF

THIS SMOKE/CO ALARM

1 Mounting Bracket

2 Mounting Slots

3 Locking Pins

(break out of bracket)

4 Hot (Black) AC Wire

5 Neutral (White) AC Wire

6 Interconnect (Orange) Wire

7 Quick-Connect

Power Connector

8 Turn this way to

remove from bracket

9 Turn this way to

attach to bracket

10 Slide-Out Battery Drawer

FOLLOW THESE SIMPLE STEPS

The basic installation of this Smoke/CO Alarm is similar whether you want to install one Alarm, or

interconnect more than one Alarm. If you are interconnecting more than one Alarm, you read MUST

“Special Requirements For Interconnected Alarms” below before you begin installation.

DANGER!

ELECTRICAL SHOCK HAZARD. Turn off power to

the area where you will install this unit at the

circuit breaker or fuse box before beginning

installation. Failure to turn off the power before

installation may result in serious electrical

shock, injury or death.

1. Remove the mounting bracket from the base,

and attach it to the junction box.

2. Using wire nuts, connect the power connector to

the household wiring.

STAND-ALONE ALARM ONLY:

• Connect the white wire on the power connector to the neutral wire in the junction box.

• Connect the black wire on the power connector to the hot wire in the junction box.

• Tuck the orange wire inside the junction box. It is used for interconnect only.

INTERCONNECTED UNITS ONLY:

• Strip off about 1/2" (12 mm) of the plastic coating on the orange wire on the

power connector.

• Connect the white wire on the power connector to the neutral wire in the junction box.

• Connect the black wire on the power connector to the hot wire in the junction box.

•

Connect the orange wire on the power connector to the interconnect wire in the junction box.

Repeat for each unit you are interconnecting. Never connect the hot or neutral wires in the

junction box to the orange interconnect wire. Never cross hot and neutral wires between Alarms.

3. If there’s a battery pull tab, activate the battery back-up by removing the “Pull to Activate Battery

Back-Up” tab. If batteries are not installed, install battery back-up. Battery back-up cannot work

until you install the battery in the correct position (Match “+” to “+” and “-” to “-”).

4. Plug the power connector into the back of the Alarm.

5. Position the base of the Alarm over the mounting bracket, and turn the Alarm clockwise (right) until

the unit is in place. If wall mounted, adjust unit so words are level.

6. Check all connections.

! WARNING!

Improper wiring of the power connector or the wiring leading to the power connector will cause

damage to the Alarm and may lead to a non-functioning Alarm.

STAND-ALONE ALARM ONLY:

• If you are only installing one Alarm, restore power to the junction box.

INTERCONNECTED UNITS ONLY:

• If you are interconnecting multiple Alarms, repeat steps 1-6 for each Alarm in the series.

When you are nished, restore power to the junction box.

DANGER!

ELECTRICAL SHOCK HAZARD. Do not restore power until all Alarms are completely installed.

Restoring power before installation is complete may result in serious electrical shock,

injury or death.

7. Turn AC power back on. Under normal operation, the Green power indicator light will

shine continuously.

8. If the Green power indicator light does not light, and TURN OFF POWER TO THE JUNCTION BOX

recheck all connections. If all connections are correct and the Green power indicator still does not

light when you restore the power, the unit should be replaced immediately.

9. Test each Alarm. Press and hold the Test/Silence button until the unit Alarms. When testing a

series of interconnected units you must test each unit individually. Make sure all units

Alarm when each one is tested.

DANGER!

If any unit in the series does not Alarm, TURN OFF POWER and recheck connections. If it does

not Alarm when you restore power, replace it immediately.

SPECIAL REQUIREMENTS FOR INTERCONNECTED ALARMS

! WARNING!

• Failure to meet any of the above requirements could damage the units and cause them to

malfunction, removing your protection.

• AC and AC/DC Alarms can be interconnected. Under AC power, all units will Alarm when

one senses smoke or CO. When power is interrupted, only the AC/DC units in the series will

continue to send and receive signals. AC powered Alarms will not operate.

Interconnected units can provide earlier warning of re than stand-alone units, especially if a re

starts in a remote area of the dwelling. If any unit in the series senses smoke, all units will Alarm. To

determine which Alarm initiated an Alarm, see table:

During an Alarm On Initiating Alarm(s): Red LED(s) ashes (ash) rapidly

On All Other Alarms: Red LED is Off

After an Alarm (Latching)

On Initiating Alarm(s): Red LED(s) On for

2 seconds/Off for 2 seconds

On All Other Alarms: Green LED(s) On, Red LED(s) Off

COMPATIBLE INTERCONNECTED UNITS

IMPORTANT!

Interconnect units within a single family residence only. Otherwise all households will experience

unwanted alarms when you test any unit in the series. Interconnected units will only work if they are

wired to compatible units and all requirements are met. This unit is designed to be compatible with:

First Alert

Smoke Alarm Model: SMI100-AC, and Smoke/CO Model: SMCO100V-AC; BRK Electronics

Smoke Alarm Models 9120, 9120B, SC9120B, 7010, 7010B; BRK Electronics

Heat Alarm Models

HD6135F; BRK Electronics

CO Alarm Models CO5120BN, CO5120PDBN; Smoke/CO Alarm Model

SC7010BV, SC7010B.

INTERCONNECTED UNITS MUST MEET ALL OF THE FOLLOWING REQUIREMENTS:

• A maximum of 18 compatible units may be interconnected (Maximum of 12 Smoke Alarms).

• The same fuse or circuit breaker must power all interconnected units.

• The total length of wire interconnecting the units should be less than 1000 feet (300 meters). This

type of wire is commonly available at Hardware and Electrical Supply stores.

• All wiring must conform to all local electrical codes and NFPA 70 (NEC). Refer to NFPA 72, NFPA

101, and/or your local building code for further connection requirements.

A Unswitched 120VAC 60 Hz source B To additional units; Maximum =

18 total (Maximum 12 Smoke Alarms)

1 Alarm

2 Ceiling or Wall

3 Power Connector

4 Wire Nut

5 Junction Box

6 Neutral Wire (White)

7 Interconnect Wire

(Orange)

8 Hot Wire (Black)

STEP BY STEP GUIDE TO PROGRAMMING THIS ALARM

For First Time and When Changing Batteries

Action Alarm Will Say

Insert batteries (2, AA batteries)

“Welcome, First Alert Carbon Monoxide

and Smoke Alarm.”

“No location programmed” if rst time or “[Location,

example: “Basement”] location programmed” when

changing batteries.

“To select location, press and hold test button now.”

Press & hold test button if

you would like to program the

location or change the location

of the alarm. Release button

after alarm responds.

“To save location, press and hold test button

after location is heard.” Alarm will speak list of

locations (see below).

After you hear the location

of where you are placing

the alarm, press & hold

the test button.

“[Location, example: “Basement”] location saved.” If no

location is chosen: “No location saved.”

Your Alarm has now been programmed for the location of your choice.

Available Locations: Basement, Hallway, Ofce, Child’s Bedroom, Kitchen, Utility Room,

Dining Room, Living Room, Family Room, Master Bedroom, Guest Bedroom, No Location.

For Reprogramming: When it is necessary to reprogram the Alarm after the unit has been

activated and is in normal operation: Tap the test button 5 times to reset the Alarm to again

access the programming menu.

Action What You Will See & Hear

Normal Operations Voice: Power/Smoke LED: Silent; Constant Green;

Horn: CO LED: Silent; Off

When You Test the Alarm

Voice: “Testing.” Horn: 3 beeps, pause, 3 beeps;

Voice: “Warning, evacuate smoke in [Location,

example: “Basement”]. Evacuate.”; Power/Smoke

LED: CO Flashes Red in sync with the horn pattern;

LED: Horn: Off, followed by 4 fast beeps, pause, 4 fast

beeps; “Warning, evacuate carbon monoxide in Voice:

[Location, example: “Basement”]. Evacuate.” Pause.

“Highest carbon monoxide level was [CO level example:

_0_ ppm]”; Off; Flashes Power/Smoke LED: CO LED:

Red in sync with the horn pattern.

If Battery Becomes

Low or is Missing

Voice: “Replace battery in [Location, example

“Basement”].” Repeated every 5 hours; chirps Horn:

once a minute; Flashes Green On Power/Smoke LED:

for 2 seconds/Off for 2 seconds. Low Battery Latch is

now engaged. Flashes Green once a minute if AC power

is off; OffCO LED:

If Alarm is Not

Operating Properly

(MALFUNCTION SIGNAL)

Voice: “Detector error in [Location, example

“Basement”], please see manual.” Repeated every

5 hours; 3 chirps every minute; Horn: Power/

Smoke LED: 3 Green Flashes approximately once a

minute; OffCO LED:

Alarm has reached

its End of Life

Voice: “Detector error in [Location, example

“Basement”], please see manual.” Repeated every

5 hours; 5 chirps every minute; Horn: Power/

Smoke LED: 5 Green Flashes approximately once a

minute; OffCO LED:

Smoke is Detected

Horn: 3 beeps, pause, repeating 9 times; Voice:

“Warning, evacuate smoke in [Location, example:

“Basement”]. Evacuate.”; 3 beeps, pause, Horn:

repeating 2 times followed by Voice Warning above;

Power/Smoke LED: During Alarm: Flashes Red in sync

with the horn pattern. After Alarm: Flashes Red On for

2 seconds/Off for 2 seconds. Smoke Alarm Latch is now

engaged; OffCO LED:

Alarm Levels of CO are Detected

Horn: 4 fast beeps, pause, 4 fast beeps, pause*; Voice:

“Warning, evacuate carbon monoxide in [Location,

example: “Basement”]. Evacuate.” Pause. “Highest

carbon monoxide level was [CO level example: ___

ppm]”; 4 beeps, pause, 4 beeps, pause repeating Horn:

2 times followed by Voice Warning above; Power/

Smoke LED: CO LED: Off; During Alarm: Flashes Red

in sync with the horn pattern. After Alarm: Flashes Red

On for 2 seconds/Off for 2 seconds. CO Alarm Latch

is now engaged.

*NOTE: If unit goes into CO Alarm, the regular 4 beeps-

brief pause cycle will repeat for fteen minutes. After

fteen minutes, the pause will increase to one minute.

Smoke Alarm is Silenced Voice: “Horn silenced. Detector active.”; Off; Horn:

Power/Smoke LED: CO LED: Flashes Red; Off

CO Alarm is Silenced Voice: “Horn silenced. Detector active.”; Off; Horn:

Power/Smoke LED: CO LED: Off; Flashes Red

04 ALARM FEATURES

• Friendly voice tells you what the danger is and it’s location.Voice & Location Alerts:

• When one alarm sounds, all compatible* alarms sound.Early Warning Interconnect:

• Allows for easy installation. No need to rewire.Quick Connect Plug:

LOCKING FEATURES

The locking features are designed to discourage unauthorized removal of the batteries

or Alarm. It is not necessary to activate the locks in single-family households where

unauthorized battery or Alarm removal is not a concern.

These Alarms have two separate locking features: one to lock the battery compartment, and

the other to lock the Alarm to the mounting bracket. You can choose to use either feature

independently, or use them both.

Tools you will need: Needle-nose pliers,

Standard Flathead screwdriver.

Both locking features use locking pins, which

are molded into the mounting bracket. Using

needle-nose pliers, remove one or both pins

from the mounting bracket, depending on how

many locking features you want to use.

IMPORTANT!

To permanently remove either lock, insert a athead screwdriver between the locking

pin and the lock, and pry the pin out of the lock.

TO LOCK THE BATTERY COMPARTMENT

Do not lock the battery compartment until you have installed the battery and tested the

battery back-up.

1. Push and hold Test/Silence button until

the Alarm sounds.

IMPORTANT!

If the unit does not Alarm during testing, DO

NOT lock the battery compartment! Install a

new battery and test again. If the Alarm still

does not Alarm, replace it immediately.

2. Using needle-nose pliers, detach one locking pin

from the mounting bracket.

3. Push the locking pin through the hole near the

battery drawer on the back of the Alarm.

TO UNLOCK THE BATTERY COMPARTMENT

IMPORTANT!

Once the Alarm is installed, you must disconnect it from the AC power before unlocking

the battery compartment.

DANGER!

ELECTRICAL SHOCK HAZARD. Turn off the power to the area where the Alarm is

installed before removing it from the mounting bracket. Failure to turn off the power

rst may result in serious electrical shock, injury or death.

! WARNING!

Always discharge the branch circuit before servicing an AC or AC/DC Alarm. First, turn off

the AC power at the circuit breaker or fuse box. Next, remove the battery from Alarms with

battery back-up. Finally, press and hold the Test/Silence button for 5-10 seconds to discharge

the branch circuit.

1. Remove the Alarm from the mounting bracket.

If the unit is locked to the bracket, see the

section “To Unlock the Mounting Bracket.”

2. Disconnect the power connector by gently

prying it away from the back of the Alarm.

3. Insert a athead screwdriver under the head

of the locking pin, and gently pry it out of

the battery compartment lock. (If you plan

to relock the battery compartment, save

the locking pin.)

4. To relock the battery compartment, close the battery door and reinsert locking pin in lock.

5. Reconnect the power connector to the back of the Alarm, reattach the Smoke Alarm to the

mounting bracket, and restore the power.

IMPORTANT!

When replacing the batteries, always test the Alarm before relocking the battery compartment.

TO LOCK THE MOUNTING BRACKET

1. Using needle-nose

pliers, detach one

locking pin from

mounting bracket.

2. Insert the locking pin

into the lock located

opposite from the

battery drawer as

shown in the diagram.

3. When you attach

the Alarm to the

mounting bracket,

the locking pin’s head

will t into a notch

on the bracket.

TO UNLOCK THE MOUNTING BRACKET

DANGER!

ELECTRICAL SHOCK HAZARD. Turn off the power to the area where the Alarm is

installed before removing it from the mounting bracket. Failure to turn off the power

rst may result in serious electrical shock, injury or death.

! WARNING!

Always discharge the branch circuit before servicing

an AC or AC/DC Alarm. First, turn off the AC power

at the circuit breaker or fuse box. Next, remove the

battery from Alarms with battery back-up. Finally,

press and hold the Test/Silence button for 5-10

seconds to discharge the branch circuit.

1. Insert a athead screwdriver between the

mounting bracket pin and the mounting bracket.

2. Pry the Alarm away from the bracket by

turning both the screwdriver and the Alarm

counterclockwise (left) at the same time.

05 TESTING & MAINTENANCE

WEEKLY TESTING

! WARNING!

• use an open ame of any kind to test this unit. You might accidentally damage or set re NEVER

to the unit or to your home. use vehicle exhaust! Exhaust may cause permanent damage NEVER

and voids your warranty.

• If the Alarm ever fails to test properly, replace it immediately. Products under warranty may be

returned to the manufacturer for replacement. See “Limited Warranty” at the end of this manual.

! CAUTION!

It is important to test this unit every week to make sure it is working properly. Using the test

button is the recommended way to test this Smoke/CO Alarm.

You can test this Smoke/CO Alarm by pressing and holding the Test/Silence button on the Alarm

cover until Alarm Voice says “Testing” (typically 3-5 seconds).

Activate the Alarm test, reset or silence function by use of a nger or thumb. Use of any other

instrument is strictly prohibited.

During testing, you will see and hear the following sequence:

• The Alarm Voice will say “Testing.” The Horn will sound 3 beeps, pause, 3 beeps. The Alarm Voice

will say “Warning, evacuate smoke in [Location, example: “Basement”]. Evacuate.” The Power/

Smoke LED CO LED ashes Red and the will be Off.

• Next the Horn will sound 4 beeps, pause, 4 beeps. The Alarm Voice will say “Warning, evacuate

carbon monoxide in [Location, example: “Basement”]. Evacuate.” The Power/Smoke LED will be

Off and the ashes Red.CO LED

If the unit does not alarm, make sure the batteries are correctly installed, and test again. If the

unit still does not alarm, replace it immediately.

REGULAR MAINTENANCE

This unit has been designed to be as maintenance-free as possible, but there are a few simple things

you must do to keep it working properly:

• Test it at least once a week.

• Clean the Smoke/CO Alarm at least once a month; gently vacuum the outside of the Smoke/CO

Alarm using your household vacuum’s soft brush attachment. Test the Smoke/CO Alarm. Never use

water, cleaners or solvents since they may damage the unit.

• If the Smoke/CO Alarm becomes contaminated by excessive dirt, dust and/or grime, and cannot be

cleaned to avoid unwanted alarms, replace the unit immediately.

• If the green power LED ashes 2 times every minute (horn is silent) it means that the Alarm needs

to be cleaned as indicated above. If green light continues to ash, replace Alarm.

• Relocate the unit if it sounds frequent unwanted alarms. See “Where This Alarm Should Not Be

Installed” for details.

• When the battery back-up becomes weak, the Alarm will “chirp” about once a minute (the low

battery warning), and the will say “Replace battery in [Location, example “Basement”].” Voice

Repeated every 5 hours. This warning should last 7 days, but you should replace the battery

immediately to continue your protection. The Low Battery Latch feature will be engaged. The

Green Power/Smoke LED will ash On for 2 seconds/Off for 2 seconds.

• Protect or cover the alarm when doing any maintenance to home i.e. sanding oors, painting,

drywall patching, etc. to prevent contamination.

CHOOSING A REPLACEMENT BATTERY:

Your Smoke/CO Alarm requires two “AA” Duracell MN1500/LR6 and Energizer E91 batteries. These

batteries are available at many local retail stores.

! WARNING!

• Always use the exact batteries specied by this User’s Manual. use rechargeable DO NOT

batteries. Clean the battery contacts and also those of the device prior to battery installation.

Install batteries correctly with regard to polarity (+ and -).

• Please dispose of or recycle used batteries properly, following any local regulations. Consult your

local waste management authority or recycling organization to nd an electronics recycling facility

in your area. DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY EXPLODE OR LEAK.

! WARNING!

• Keep battery out of reach of children. In the event a battery is swallowed, immediately contact

your poison control center, your physician, or the National Battery Ingestion hotline at

202-625-3333 as serious injury may occur.

IMPORTANT!

Actual battery service life depends on the Alarm and the environment in which it is installed. All

the batteries specied above are acceptable replacement batteries for this unit. Regardless of the

manufacturer’s suggested battery life, you replace the battery immediately once the unit starts MUST

“chirping” (the “low battery warning”).

To replace the batteries (without removing Alarm from the ceiling or wall):

1. Open the battery compartment.

2. Press tabs A and B as shown in the diagram

and remove each battery.

3. Insert the new batteries, making sure they

snap completely into the battery compartment.

Match the terminals on the ends of the

batteries with the terminals on the unit.

4. Close the battery compartment, and then test

the unit by pressing the Test/Silence button.

TROUBLESHOOTING GUIDE

DANGER!

ELECTRICAL SHOCK HAZARD. Turn off the power to the area where the Alarm is installed

BEFORE removing it from the mounting bracket or checking any electrical connections!

Failure to turn off the power rst may result in electrical shock, injury or death.

IF THE ALARM... PROBLEM... YOU SHOULD...

Horn “chirps” and LED

ashes green about once

per minute, or LED ashes

Green On for 2 seconds/

Off for 2 seconds. (Low

Battery Latch is engaged.)

Voice: “Replace battery in

[Location]” every 5 hours

Low battery warning. Install two

new AA batteries*.

Horn “chirps” and Green

LED ashes 3 times

every minute. Voice:

“Detector error in [Location,

example “Basement”],

please see manual”,

repeated every 5 hours.

MALFUNCTION SIGNAL.

Device is not working

properly, and needs

to be replaced.

If unit is under warranty,

contact Consumer

Support to process a

warranty replacement.

Horn “chirps” and Green

LED ashes 5 times

every minute. Voice:

“Detector error in [Location,

example “Basement”],

please see manual”,

repeated every 5 hours.

END OF LIFE SIGNAL.

Alarm needs to

be replaced.

Immediately

replace the Alarm.

Power LED ashes Green 2

times every minute. Alarm requires cleaning.

Clean Alarm then press

and release the test button.

See Regular Maintenance

section. If Green LED

Continues to ash, contact

Consumer Support.

CARBON MONOXIDE ALARM ONLY

CO Alarm goes back into

alarm 4 minutes after

you Silence it.

CO levels indicate

a potentially

dangerous situation.

IF YOU ARE FEELING

SYMPTOMS OF CO

POISONING, EVACUATE

your home and call 911

or the Fire Department.

Refer to “If The CO Alarm

Sounds” for details.

CO Alarm sounds frequently

even though no high levels

of CO are revealed in

an investigation.

The CO Alarm may be

improperly located. Refer

to “Where to Install This

Alarm” for details.

Relocate your Alarm. If

frequent alarms continue,

have home rechecked for

potential CO problems. You

may be experiencing an

intermittent CO problem.

SMOKE ALARM ONLY

Smoke Alarm sounds when

no smoke is visible.

Unwanted alarm may be

caused by nonemergency

source like cooking smoke.

Silence Alarm using

manual button; clean the

Alarm’s cover with a soft,

clean cloth. If frequent

unwanted alarms continue,

relocate your Alarm. Alarm

may be too close to a

kitchen, cooking appliance,

or steamy bathroom.

*For a list of acceptable replacement batteries, see “Choosing a Replacement Battery.”

If you have questions that cannot be answered by reading this manual, call the

Consumer Support Team at 1-800-323-9005

FIRE SAFETY TIPS

Follow safety rules and prevent hazardous situations: 1) Use smoking materials properly. Never smoke

in bed. 2) Keep matches or lighters away from children; 3) Store ammable materials in proper

containers; 4) Keep electrical appliances in good condition and don’t overload electrical circuits;

5) Keep stoves, barbecue grills, replaces and chimneys grease- and debris-free; 6) Never leave

anything cooking on the stove unattended; 7) Keep portable heaters and open ames, like candles,

away from ammable materials; 8) Don’t let rubbish accumulate. Keep Alarms clean, and test them

weekly. Replace Alarms immediately if they are not working properly. Smoke Alarms that do not work

cannot alert you to a re. Keep at least one working re extinguisher on every level, and an additional

one in the kitchen. Have re escape ladders or other reliable means of escape from an upper level in

case stairs are blocked; 9) Have an escape plan and practice it regularly.

06 IF YOUR SMOKE/CO ALARM SOUNDS

WHAT TO DO FIRST: IDENTIFY THE TYPE OF ALARM SIGNAL

Refer to previous section “What You Will See And Hear With This Alarm”.

IF THE CO ALARM SOUNDS

“ALARM-MOVE TO FRESH AIR”

If you hear the Alarm horn sound 4 beeps, pause, 4 beeps, pause, and the RED CO light

is ashing, move everyone to a source of fresh air.

! WARNING!

Actuation of your CO Alarm indicates the presence of carbon monoxide (CO) which can kill you. In

other words, when your CO Alarm sounds, you must not ignore it!

IF THE CO ALARM SIGNAL SOUNDS:

1. Press the Test/Silence button.

2. Call your emergency services, re department or 911. Write down the number of your local

emergency service here:

____________________________________________________________________

3. Immediately move to fresh air—outdoors or by an open door or window. Do a head count to check

that all persons are accounted for. Do not re-enter the premises, or move away from the open door

or window until the emergency services responder has arrived, the premises have been aired out,

and your CO Alarm remains in its normal condition.

4. After following steps 1-3, if your CO Alarm reactivates within a 24-hour period, repeat steps

1-3 and call a qualied appliance technician to investigate for sources of CO from fuel-burning

equipment and appliances, and inspect for proper operation of this equipment. If problems are

identied during this inspection have the equipment serviced immediately. Note any combustion

equipment not inspected by the technician, and consult the manufacturers’ instructions, or contact

the manufacturers directly, for more information about CO safety and this equipment. Make sure

that motor vehicles are not, and have not, been operating in an attached garage or adjacent to the

residence. Write down the number of a qualied appliance technician here:

____________________________________________________________________

NOTE: A qualied appliance technician is dened as “a person, rm, corporation, or company that

either in person or through a representative, is engaged in and responsible for the installation, testing,

servicing, or replacement of heating, ventilation, air conditioning (HVAC) equipment, combustion

appliances and equipment, and/or gas replaces or other decorative combustion equipment.”

AFTER AN ALARM

After the emergency responders arrive, the premises aired out, and your CO Alarm

remains in its normal condition, you can check what the highest carbon monoxide

level sensed was:

Action Alarm Will Say

Press & Hold Test Button

“Highest carbon monoxide level was ___

ppm. Please see manual.”

“To clear highest carbon monoxide level,

press and hold test button now.”

Press & Hold Test Button, if you would like to

clear the highest level sensed. If you would

like to keep the highest level in memory, do

not press anything.

“Highest carbon monoxide

level cleared.”

Alarm will say nothing.

IF THE SMOKE ALARM SOUNDS:

RESPONDING TO AN ALARM

! WARNING!

• If the unit alarms and you are not testing the unit, it is warning you of a potentially dangerous

situation that requires your immediate attention. ignore any alarm. Ignoring the alarm may NEVER

result in injury or death.

• Never remove the batteries from a battery operated Smoke/CO Alarm to stop an unwanted alarm

(caused by cooking smoke, etc.). Removing batteries disables the alarm so it cannot sense smoke,

and removes your protection. Instead open a window or fan the smoke away from the unit. The

alarm will reset automatically.

• If the unit alarms get everyone out of the house immediately.

WHAT TO DO IN CASE OF FIRE

• Don’t panic; stay calm. Follow your family escape plan.

• Get out of the house as quickly as possible. Don’t stop to get dressed or collect anything.

• Feel doors with the back of your hand before opening them. If a door is cool, open it slowly. Don’t

open a hot door. Keep doors and windows closed, unless you must escape through them.

• Cover your nose and mouth with a cloth (preferably damp). Take short, shallow breaths.

• Meet at your planned meeting place outside your home, and do a head count to make sure

everybody got out safely.

• Call the Fire Department as soon as possible from outside. Give your address, then your name.

• Never go back inside a burning building for any reason.

• Contact your Fire Department for ideas on making your home safer.

! WARNING!

Alarms have various limitations. See “General Limitations of Smoke/CO Alarms” for details.

07 USING THE SILENCE FEATURES

! WARNING!

Never remove the batteries to quiet an unwanted alarm. Removing the batteries disables the

alarm and removes your protection.

• The Silence Feature is intended to temporarily silence the horn while you identify and correct the

problem. Do not use the Silence Feature in emergency situations. It will not correct a CO problem

or extinguish a re.

• The Silence Feature can temporarily quiet an unwanted alarm for several minutes. You can

silence this Smoke/CO Alarm by pressing the Test/Silence button on the alarm cover for at

least 3-5 seconds.

• After the Test/Silence button is released, the Alarm Voice will say “Horn silenced, detector active.”

The Red LED blinks during the silence mode.

When the Smoke Alarm is Silenced When the CO Alarm is Silenced

The Smoke Alarm will remain silent for up to

15 minutes, then return to normal operation.

If the smoke has not cleared–or continues to

increase–the device will go back into alarm.

The CO Alarm will remain silent for

up to 4 minutes.

After 4 minutes, if CO levels remain

potentially dangerous the horn will start

sounding again.

SILENCING THE LOW BATTERY WARNING

This Silence Feature can temporarily quiet the low battery warning “chirp” for up to 8 hours if AC power

is present. Press the Test/Silence button on the Alarm cover until you hear the acknowledge “chirp”.

Once the low battery warning “chirp” Silence Feature is activated, the unit continues to ash the

green light once a minute for 8 hours. After 8 hours, the low battery “chirp” will resume. The Alarm

will continue to operate as long as AC power is supplied. However, replace the batteries as soon as

possible, to maintain protection in event of a power outage.

To deactivate this feature: Press the Test/Silence button again. The unit will go into Test Mode and

the low battery warning will resume (LED ashes and unit sounds “chirp” once a minute).

To silence alarms in an interconnected series: To silence an interconnected series of Smoke/CO

Alarms, you must press the Test/Silence button on the initiating alarm (The unit with the ashing red

light; the red light will be off on all other Alarms.). If you press the Test/Silence on any other Alarm, it

will only silence that unit, not the whole interconnected series.

SILENCING THE END OF LIFE SIGNAL

This Silence Feature can temporarily quiet the End of Life warning “chirp” for up to 2 days. You can silence

the End of Life warning “chirp” by pressing the Test/Silence button. The horn will chirp, acknowledging that

the End of Life Silence Feature has been activated. After approximately 2 days, the End of Life “chirp” will

resume. The timer shall not be able to be reset after 14 days following the initial end-of-life signal.

LATCHING FEATURES

Alarm Latch is activated after an Alarm is exposed to alarm levels of smoke or carbon

monoxide. This feature will only work with AC power. See “Special Requirements for

Interconnected Alarms” for signaling. This feature helps emergency responders, investigators,

or service technicians identify which unit(s) in your home were exposed to alarm levels of

smoke or carbon monoxide. This can help investigators pinpoint the source of smoke or CO.

Interconnected Alarms. Latching Alarm Indicator shows which Alarm(s) in the series were

exposed to alarm levels of smoke or carbon monoxide. The Latching Alarm Indicator stays

ON until you clear it, so it can alert you to an alarm that occurred while you were away from

home, even though smoke or CO present in the air has dropped below alarm levels.

LATCHING FEATURES (CONTINUED)...

Low Battery Latch

is activated when the Alarm is in the “low battery condition”. When this

occurs, the Smoke/Power LED ashes Green On for 2 seconds/Off for 2 seconds. This feature

is designed to help you identify which Alarm needs to have the battery replaced. Although, the

Alarm will sound the low battery chirp approximately once every minute, sometimes during the

initial stages of “low battery”, the Alarm will chirp in greater intervals than one minute, sometimes

up to several hours, until the battery reaches a steady low battery level. This innovative feature

eliminates the frustration of waiting for and/or identifying which unit is chirping.

Latching Alarm

Unit was exposed to

Alarm levels of smoke

Latching Not Activated

Unit was not exposed to

Alarm levels of smoke

“SMART INTERCONNECT” FEATURE

This Alarm includes “Smart Interconnect” which enables the Alarm to be interconnected with other

First Alert

and BRK Smoke, Heat, and “Smart Interconnect” CO Alarms. When smoke is detected, all

Alarms will sound the smoke horn pattern. When CO is detected, “Smart Interconnect” Alarms will

sound the CO horn pattern. Alarms that do not have the “Smart Interconnect” feature will remain silent

during a CO Alarm.

08 WHAT YOU NEED TO KNOW ABOUT CO

WHAT IS CO?

CO is an invisible, odorless, tasteless gas produced when fossil fuels do not burn completely, or are

exposed to heat (usually re). Electrical appliances typically do not produce CO.

These fuels include: Wood, coal, charcoal, oil, natural gas, gasoline, kerosene, and propane.

Common appliances are often sources of CO. If they are not properly maintained, are improperly

ventilated, or malfunction, CO levels can rise quickly. CO is a real danger now that homes are more

energy efcient. “Air-tight” homes with added insulation, sealed windows, and other weatherproong

can “trap” CO inside.

SYMPTOMS OF CO POISONING

These symptoms are related to CO POISONING and should be discussed with ALL household members.

Mild Exposure: Slight headache, nausea, vomiting, fatigue (“u-like” symptoms).

Medium Exposure: Throbbing headache, drowsiness, confusion, fast heart rate.

Extreme Exposure: Convulsions, unconsciousness, heart and lung failure. Exposure to carbon

monoxide can cause brain damage, death.

IMPORTANT!

This CO Alarm measures exposure to CO over time. It Alarms if CO levels are extremely high in a

short period of time, or if CO levels reach a certain minimum over a long period of time. The CO

Alarm generally sounds an Alarm before the onset of symptoms in average, healthy adults. Why is

this important? Because you need to be warned of a potential CO problem while you can still react in

time. In many reported cases of CO exposure, victims may be aware that they are not feeling well, but

become disoriented and can no longer react well enough to exit the building or get help. Also, young

children and pets may be the rst affected. The average healthy adult might not feel any symptoms

when the CO Alarm sounds. However, people with cardiac or respiratory problems, infants, unborn

babies, pregnant mothers, or elderly people can be more quickly and severely affected by CO. If you

experience even mild symptoms of CO poisoning, consult your doctor immediately!

FINDING THE SOURCE OF CO AFTER AN ALARM

Carbon monoxide is an odorless, invisible gas, which often makes it difcult to locate the source of CO

after an Alarm. These are a few of the factors that can make it difcult to locate sources of CO:

• House well ventilated before the investigator arrives.

• Problem caused by “backdrafting.”

• Transient CO problem caused by special circumstances.

Because CO may dissipate by the time an investigator arrives, it may be difcult to locate the

source of CO. First Alert shall not be obligated to pay for any carbon monoxide investigation

or service call.

POTENTIAL SOURCES OF CO IN THE HOME

Fuel-burning appliances like:

portable heater, gas or wood

burning replace, gas kitchen range

or cooktop, gas clothes dryer.

Damaged or insufcient venting:

corroded or disconnected water

heater vent pipe, leaking chimney

pipe or ue, or cracked heat

exchanger, blocked or clogged

chimney opening.

Improper use of appliance/

device: operating a barbecue grill

or vehicle in an enclosed area (like

a garage or screened porch).

Transient CO problems: “transient” or on-again-off-again CO problems can be caused by outdoor

conditions and other special circumstances.

The following conditions can result in transient CO situations:

1. Excessive spillage or reverse venting of fuel appliances caused by outdoor conditions such as:

Wind direction and/or velocity, including high, gusty winds. Heavy air in the vent pipes (cold/humid air

with extended periods between cycles).

• Negative pressure differential resulting from the use of exhaust fans.

• Several appliances running at the same time competing for limited fresh air.

• Vent pipe connections vibrating loose from clothes dryers, furnaces, or water heaters.

• Obstructions in or unconventional vent pipe designs which can amplify the above situations.

2. Extended operation of unvented fuel burning devices (range, oven, replace).

3. Temperature inversions, which can trap exhaust close to the ground.

4. Car idling in an open or closed attached garage, or near a home.

These conditions are dangerous because they can trap exhaust in your home. Since these

conditions can come and go, they are also hard to recreate during a CO investigation.

09 HOW CAN I PROTECT MY FAMILY FROM

CO POISONING

A CO Alarm is an excellent means of protection. It monitors the air and sounds a loud Alarm before

carbon monoxide levels become threatening for average, healthy adults. A CO Alarm is not a substitute

for proper maintenance of home appliances.

TO HELP PREVENT CO PROBLEMS AND REDUCE THE RISK OF CO POISONING:

• Clean chimneys and ues yearly. Keep them free of debris, leaves, and nests for proper air ow.

Also, have a professional check for rust and corrosion, cracks, or separations. These conditions

can prevent proper air movement and cause backdrafting. Never “cap” or cover a chimney in any

way that would block air ow.

• Test and maintain all fuel-burning equipment annually. Many local gas or oil companies and HVAC

companies offer appliance inspections for a nominal fee.

• Make regular visual inspections of all fuel-burning appliances. Check appliances for excessive rust

and scaling. Also check the ame on the burner and pilot lights. The ame should be blue. A yellow

ame means fuel is not being burned completely and CO may be present. Keep the blower door

on the furnace closed. Use vents or fans when they are available on all fuel-burning appliances.

Make sure appliances are vented to the outside. Do not grill or barbecue indoors, or in garages or

on screen porches.

• Check for exhaust backow from CO sources. Check the draft hood on an operating furnace for a

backdraft. Look for cracks on furnace heat exchangers.

• Check the house or garage on the other side of shared wall.

• Keep windows and doors open slightly. If you suspect that CO is escaping into your home, open a

window or a door. Opening windows and doors can signicantly decrease CO levels.

In addition, familiarize yourself with all enclosed materials. Read this manual in its entirety, and make

sure you understand what to do if your CO Alarm sounds.

10 REGULATORY INFORMATION

FOR SMOKE ALARMS

RECOMMENDED LOCATIONS FOR SMOKE ALARMS

INSTALLING SMOKE ALARMS IN SINGLE-FAMILY RESIDENCES

The National Fire Protection Association (NFPA), recommends one Smoke Alarm on every oor, in every

sleeping area, and in every bedroom. In new construction, the Smoke Alarms must be AC powered and

interconnected. See “Agency Placement Recommendations” for details. For additional coverage, it is

recommended that you install a Smoke Alarm in all rooms, halls, storage areas, nished attics, and

basements, where temperatures normally remain between 40˚ F (4.4˚ C) and 100˚ F (37.8˚ C). Make

sure no door or other obstruction could keep smoke from reaching the Smoke Alarms.

MORE SPECIFICALLY, INSTALL SMOKE ALARMS:

• On every level of your home, including nished attics and basements.

• Inside every bedroom, especially if people sleep with doors closed.

• In the hall near every sleeping area. If your home has multiple sleeping areas, install a unit in each.

• If a hall is over 40 feet (12 meters) long, install an Alarm at each end.

• At the top of the rst-to-second level stairway, and at bottom of basement stairway.

IMPORTANT!

Specic requirements for Smoke Alarm installation vary from state to state and from region to region.

Check with your local Fire Department for current requirements in your area. It is recommended AC

or AC/DC units be interconnected for added protection.

HARDWIREDBATTERY OPERATED & WIRELESS

MULTI-STORY RESIDENCE1-STORY RESIDENCE

Wireless Alarms

Wireless Interconnected Alarms

Hardwired Interconnected

AC or AC/DC Alarms

Smoke Alarms

CO Alarms

Both OR Combination

Smoke/CO Alarms

11 REGULATORY INFORMATION FOR CO ALARMS

WHAT LEVELS OF CO CAUSE AN ALARM?

Underwriters Laboratories Inc. Standard UL2034 requires residential CO Alarms to sound when

exposed to levels of CO and exposure times as described below. They are measured in parts per

million (ppm) of CO over time (in minutes).

UL2034 Required Alarm Points*:

• If the Alarm is exposed to 400 ppm of CO, IT MUST ALARM BETWEEN 4 and 15 MINUTES.

• If the Alarm is exposed to 150 ppm of CO, IT MUST ALARM BETWEEN 10 and 50 MINUTES.

• If the Alarm is exposed to 70 ppm if CO, IT MUST ALARM BETWEEN 60 and 240 MINUTES.

* Approximately 10% COHb exposure at levels of 10% to 95% Relative Humidity (RH).

The unit is designed not to Alarm when exposed to a constant level of 30 ppm for 30 days.

IMPORTANT!

CO Alarms are designed to Alarm before there is an immediate life threat. Since you cannot see or

smell CO, never assume it’s not present.

• An exposure to 100 ppm of CO for 20 minutes may not affect average, healthy adults, but after 4

hours the same level may cause headaches.

• An exposure to 400 ppm of CO may cause headaches in average, healthy adults after 35 minutes,

but can cause death after 2 hours.

Standards: Underwriters Laboratories Inc. Single and Multiple Station Carbon

Monoxide Alarms UL2034.

According to Underwriters Laboratories Inc. UL2034, Section 1-1. 2: “Carbon monoxide Alarms covered

by these requirements are intended to respond to the presence of carbon monoxide from sources

such as, but not limited to, exhaust from internal-combustion engines, abnormal operation of fuel-red

appliances, and replaces. CO Alarms are intended to Alarm at carbon monoxide levels below those

that could cause a loss of ability to react to the dangers of carbon monoxide exposure. ” This CO Alarm

monitors the air at the Alarm, and is designed to Alarm before CO levels become life threatening. This

allows you precious time to leave the house and correct the problem. This is only possible if Alarms

are located, installed, and maintained as described in this manual.

Gas Detection at Typical Temperature and Humidity Ranges: The CO Alarm is not formulated to

detect CO levels below 30 ppm typically. UL tested for false Alarm resistance to Methane (500 ppm),

Butane (300 ppm), Heptane (500 ppm), Ethyl Acetate (200 ppm), Isopropyl Alcohol (200 ppm) and

Carbon Dioxide (5000 ppm). Values measure gas and vapor concentrations in parts per million.

Audible Alarm: 85 dB minimum at 10 feet (3 meters).

12 AGENCY PLACEMENT RECOMMENDATIONS

Standards: Underwriters Laboratories Inc. Single and Multiple Station Smoke Alarms 217.

NFPA 72 CHAPTER 29 “FOR YOUR INFORMATION, THE NATIONAL FIRE ALARM AND SIGNALING

CODE, NFPA 72, READS AS FOLLOWS:”

29.5.1* Required Detection.

29.5.1.1* Where required by other governing laws, codes, or standards for a specic type of

occupancy, approved single and multiple-station Smoke Alarms shall be installed as follows:

1. *In all sleeping rooms and guest rooms

2. *Outside of each separate dwelling unit sleeping area, within 21 ft (6.4 m) of any door to a

sleeping room, with the distance measured along a path of travel

3. On every level of a dwelling unit, including basements

4. On every level of a residential board and care occupancy (small facility), including basements and

excluding crawl spaces and unnished attics

5. *In the living area(s) of a guest suite

6. In the living area(s) of a residential board and care occupancy (small facility)

(Reprinted with permission from NFPA 72

National Fire Protection Association, Quincy, MA 02269. This reprinted material is not the complete

and ofcial position of the National Fire Protection Association, on the referenced subject which is

represented only by the standard in its entirety).

(National Fire Alarm and Signaling Code

and NFPA 72

are registered trademarks of the National Fire

Protection Association, Inc., Quincy, MA 02269).

CALIFORNIA STATE FIRE MARSHAL (CSFM)

Early warning detection is best achieved by the installation of re detection equipment in all rooms

and areas of the household as follows: A Smoke Alarm installed in each separate sleeping area (in

the vicinity, but outside bedrooms), and Heat or Smoke Alarms in the living rooms, dining rooms,

bedrooms, kitchens, hallways, nished attics, furnace rooms, closets, utility and storage rooms,

basements, and attached garages.

13 SPECIAL COMPLIANCE CONSIDERATIONS

This Smoke Alarm is suitable for use in apartments, condominiums, townhouses, hospitals, day care

facilities, health care facilities, boarding houses, group homes and dormitories provided a primary re

detection system already exists to meet re detection requirements in common areas like lobbies,

hallways, or porches. Using this Smoke Alarm in common areas may not provide sufcient warning to

all residents or meet local re protection ordinances/regulations.

This Smoke Alarm alone is not a suitable substitute for complete re detection systems in places

housing many people—like apartment buildings, condominiums, hotels, motels, dormitories, hospitals,

health care facilities, nursing homes, day care facilities, or group homes of any kind. It is not a

suitable substitute for complete re detection systems in warehouses, industrial facilities, commercial

buildings, and special-purpose non-residential buildings which require special re detection and Alarm

systems. Depending on the building codes in your area, this Smoke Alarm may be used to provide

additional protection in these facilities.

In new construction, most building codes require the use of AC or AC/DC powered Smoke Alarms only.

In existing construction, AC, AC/DC, or DC powered Smoke Alarms can be used as specied by local

building codes. THIS EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THE NATIONAL FIRE

PROTECTION ASSOCIATION’S STANDARD 72 (National Fire Protection Association, Batterymarch Park,

Quincy, MA 02269). Refer to NFPA 101 (Life Safety Code), local building codes, or consult your Fire

Department for detailed re protection requirements in buildings not dened as “households”.

FCC COMPLIANCE

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that of the receiver.

• Consult the dealer or an experienced radio or TV technician for help.

! WARNING!

Changes or modications to the product, not expressly approved by First Alert, could void the user’s

authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

14 GENERAL LIMITATIONS OF

SMOKE/CO ALARMS

This Smoke/CO Alarm is intended for residential use. It is not intended for use in industrial

applications where Occupational Safety and Health Administration (OSHA) requirements for Carbon

Monoxide Alarms must be met. The Smoke Alarm portion of this device is not intended to alert hearing

impaired residents. Special purpose Smoke Alarms should be installed for hearing impaired residents

(CO Alarms are not yet available for the hearing impaired).

Smoke/CO Alarms may not waken all individuals. Practice the escape plan at least twice a year,

making sure that everyone is involved – from kids to grandparents. Allow children to master re

escape planning and practice before holding a re drill at night when they are sleeping. If children

or others do not readily waken to the sound of the Smoke/CO Alarm, or if there are infants or family

members with mobility limitations, make sure that someone is assigned to assist them in re drill and

in the event of an emergency. It is recommended that you hold a re drill while family members are

sleeping in order to determine their response to the sound of the Smoke/CO Alarm while sleeping and

to determine whether they may need assistance in the event of an emergency.

Smoke/CO Alarms cannot work without power. Battery operated units cannot work if the batteries

are missing, disconnected or dead, if the wrong type of batteries are used, or if the batteries are not

installed correctly. AC units cannot work if the AC power is cut off for any reason (open fuse or circuit

breaker, failure along a power line or at a power station, electrical re that burns the electrical wires,

etc.). If you are concerned about the limitations of battery or AC power, install both types of units.

This Smoke/CO Alarm will not sense smoke or CO that does not reach the sensors. It will

only sense smoke or CO at the sensor. Smoke or CO may be present in other areas. Doors or other

obstructions may affect the rate at which CO or smoke reaches the sensors. If bedroom doors are

usually closed at night, we recommend you install an Alarm device (Combination CO and Smoke Alarm,

or separate CO Alarms and Smoke Alarms) in each bedroom and in the hallway between them.

This Smoke/CO Alarm may not sense smoke or CO on another level of the home. Example:

This Alarm device, installed on the second oor, may not sense smoke or CO in the basement For

this reason, one Alarm device may not give adequate early warning. Recommended minimum

protection is one Alarm device in every sleeping area, every bedroom, and on every level of your

home. Some experts recommend battery powered smoke and CO Alarms be used in conjunction with

interconnected AC powered Smoke Alarms. For details, see “About Smoke Alarms” for details.

Smoke/CO Alarms may not be heard. The Alarm horn loudness meets or exceeds current UL

standards of 85 dB at 10 feet (3 meters). However, if the Smoke/CO Alarm is installed outside the

bedroom, it may not wake up a sound sleeper or one who has recently used drugs or has been

drinking alcoholic beverages. This is especially true if the door is closed or only partly open. Even

persons who are awake may not hear the Alarm horn if the sound is blocked by distance or closed

doors. Noise from trafc, stereo, radio, television, air conditioner, or other appliances may also prevent

alert persons from hearing the Alarm horn. This Smoke/CO Alarm is not intended for people who are

hearing impaired.

The Alarm may not have time to Alarm before the re itself causes damage, injury, or death,

since smoke from some res may not reach the unit immediately. Examples of this include

persons smoking in bed, children playing with matches, when a person’s clothing catches re

while cooking, res caused by violent explosions resulting from escaping gas, or incendiary

res where the re grows so rapidly that an occupant’s egress is blocked even with properly

located Smoke Alarms.

This Smoke/CO Alarm is not a substitute for life insurance. Though this Smoke/CO Alarm warns

against increasing CO levels or the presence of smoke, First Alert does not warrant or imply in any way

that they will protect lives. Homeowners and renters must still insure their lives.

This Smoke/CO Alarm has a limited life. Although this Smoke/CO Alarm and all of its parts have

passed many stringent tests and are designed to be as reliable as possible, any of these parts could

fail at any time. Therefore, you must test this device weekly. The unit should be replaced immediately

if it is not operating properly.

This Smoke/CO Alarm is not foolproof. Like all other electronic devices, this Smoke/CO Alarm has

limitations. It can only detect smoke or CO that reaches the sensors. It may not give early warning of

the source of smoke or CO is in a remote part of the home, away from the Alarm device.

15 LIMITED WARRANTY

First Alert

warrants that for a period of ten years from the date of purchase, this product will be free

from defects in material and workmanship. First Alert, at its option, will repair or replace this product

or any component of the product found to be defective during the warranty period. Replacement

will be made with a new or remanufactured product or component. If the product is no longer

available, replacement may be made with a similar product of equal or greater value. This is your

exclusive warranty.

This warranty is valid for the original retail purchaser from the date of initial retail purchase and is

not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty

performance. First Alert dealers, service centers, or retail stores selling First Alert products do not have

the right to alter, modify or any way change the terms and conditions of this warranty.

This warranty does not cover normal wear of parts or damage resulting from any of the following:

negligent use or misuse of the product, use on improper voltage or current, use contrary to the

operating instructions, disassembly, repair or alteration by anyone other than First Alert or an

authorized service center. Further, the warranty does not cover Acts of God, such as re, ood,

hurricanes and tornadoes or any batteries that are included with this unit.

First Alert shall not be liable for any incidental or consequential damages caused by the breach of any

express or implied warranty. Except to the extent prohibited by applicable law, any implied warranty

of merchantability or tness for a particular purpose is limited in duration to the duration of the above

warranty. Some states, provinces or jurisdictions do not allow the exclusion or limitation of incidental

or consequential damages or limitations on how long an implied warranty lasts, so the above

limitations or exclusion may not apply to you. This warranty gives you specic legal rights, and you

may also have other rights that vary from state to state or province to province.

HOW TO OBTAIN WARRANTY SERVICE

Service: If service is required, do not return the product to your retailer. In order to obtain warranty

service, contact the Consumer Support Team at 1-800-323-9005. To assist us in serving you, please

have the model number and date of purchase available when calling.

Battery: First Alert makes no warranty, express or implied, written or oral, including that of

merchantability or tness for any particular purpose with respect to battery.

Disposal: Please follow local guidelines regarding the disposal or recycling of batteries

and/or electronics.

For your records, please record:

Date Purchased: ___________________________

Where Purchased: __________________________

Date Installed: __________/__________Month/Year

Replace Alarm 10 years after installation.

Please write the date in the space provided:_____________/____________ Month/Year

The Alarm will also provide an audible End-of-Life Signal approximately 10 years after

installation to remind you to replace the unit.

The End-of-Life Signal can be silenced for up to 2 days. Do not unplug or deactivate the Alarm

until you get replacement.

Printed in Mexico | M08-179720 12/22

CONFORMS TO UL STD 217 AND UL STD 2034

120 VAC ~ 60Hz, 0.07A

rstalert.com

manufactured by Resideo Technologies, Inc. and its afliates. 3901 Liberty Street,

Aurora, IL 60504-8122. Consumer Support Team: (800) 323-9005 | rstalert.com

Produktspezifikationen

Marke:	First Alert
Kategorie:	Rauchmelder
Modell:	SMCO100V-AC

Brauchst du Hilfe?

Wenn Sie Hilfe mit First Alert SMCO100V-AC benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage

Bedienungsanleitung Rauchmelder First Alert

First Alert HD6135FB Bedienungsanleitung

14 Oktober 2024

First Alert SA710CE Bedienungsanleitung

11 Oktober 2024

First Alert SA410 Bedienungsanleitung

2 Oktober 2024

First Alert SA900 Bedienungsanleitung

22 September 2024

First Alert CO600 Bedienungsanleitung

13 September 2024

First Alert P1010 Bedienungsanleitung

5 September 2024

First Alert SMCO210 Bedienungsanleitung

4 September 2024

First Alert SMCO210V Bedienungsanleitung

4 September 2024

First Alert SMCO100V-AC Bedienungsanleitung

4 September 2024

First Alert SMICO100-AC Bedienungsanleitung

4 September 2024

Bedienungsanleitung Rauchmelder

Neueste Bedienungsanleitung für -Kategorien-

FirstAlert SA700 Bedienungsanleitung

16 Oktober 2024

Alecto SA-100 Bedienungsanleitung

16 Oktober 2024

Clas Ohlson 32-3383 Bedienungsanleitung

14 Oktober 2024

Siemens DELTA reflex SD230N Bedienungsanleitung

9 Oktober 2024

Elro FS151021M Bedienungsanleitung

9 Oktober 2024

TFA AirCo2ntrol Life Bedienungsanleitung

8 Oktober 2024

FireAngel HT-630-EU Bedienungsanleitung

7 Oktober 2024

Elro 2001-023 Bedienungsanleitung

4 Oktober 2024

Pyle PCMM05 Bedienungsanleitung

3 Oktober 2024

FireHawk FHB10 Bedienungsanleitung

2 Oktober 2024