Draper Luma Bedienungsanleitung
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Draper Luma (1 Seiten) in der Kategorie Projektionsleinwand. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/1
Crimp
Crimp
Luma pictured
Operating Instructions—Standard
To lower picture surface, pull screen down. —then allow screen to retract Hesitate
very slowly until it locks in place.
To raise picture surface, pull screen down and, while holding, allow for slow
retraction into the case to reduce risk of injury from falling screen.
Operating Instructions—AutoReturn (Available with Luma)
To lower picture surface, pull screen down. —then allow screen to retract Hesitate
very slowly until it locks in place.
To raise picture surface, pull screen down gently until it stops, then release.
Wall Mounting
(Hardware not Included)
Ceiling Suspended
(Hardware not Included)
T–Bar Twist Clips
(Optional Equipment)
Extension Brackets
(Optional Equipment)
If you encounter any diffi culties installing or servicing your screen, call your dealer
or Draper, Inc., Spiceland, Indiana, (765) 987-7999, or fax (765) 987-7142.
Copyright © 2010 Draper Inc. Form Luma-Star_Inst10 Printed in U.S.A.
Installation/Operating Instructions
Luma and Star Spring Roller Operated Projection Screens by Draper
Installation
Your Draper screen can be mounted on a wall or suspended from the ceiling or
extension brackets. It must be mounted level and with the fl at back parallel to the
wall.
The screen (or extension brackets) should be mounted into studs or blocking in the
wall/ceiling, or in drywall (minimum thickness ½") with specifi ed anchors. For any
other type of installation, follow all local build ing and safety codes.
Steel studs, concrete or cinder block walls and all other types of non-wood frame
construction require the use of special screws or anchors.
The selection of ap pro pri ate mounting hardware should be made by a
qualifi ed professional installer.
Use the upper portion of the holes at the back of the endcap/mounting bracket
for fl ush wall mount ing. Recommended hard ware (not included): For mount ing
into wood or wall stud, use #10 x 1¼" wood screws; for mount ing into dry wall
(minimum ½" thick), use 3/16" tog gle bolts or 3/16" molly bolts. DO NOT USE FLAT
HEAD SCREWS. DO NOT OVERTIGHTEN.
Use the holes at the front of the endcap/
mount ing brack et for sus pend ed mount ing.
Po si tion and prop er ly an chor screw eyes or
oth er fasteners (not included) into ceil ing
joists or oth er sol id sur face. Sus pend “S”
hooks (not included) from fas ten ers (not
included) and hook through holes in the
front of the mount ing brack et. For added
safe ty, crimp both ends of the “S” hooks so
the screen can not come off.
Recommended hardware (not included):
For mount ing into wood or ceil ing joist,
use two
3
/
16
" x 1
1
/
4
" screw eyes and
3
/
16
"
di am e ter “S” hooks; for mount ing into
dry wall (min i mum
1
/
2
" thick), use
3
/
16
" tog gle
or molly bolts with
3
/
16
" “S” hooks.
Wall mount the brackets (not in clud ed
with screen) using hard ware recom-
mended for “Wall Mounting” (above, not
included). Then, sus pend the screen from
the front holes with “S” hooks. For added
safe ty, crimp both ends of the “S” hooks
so the screen can not come off.
DO NOT OVERTIGHTEN.
®
➀ Loosen the clip assembly by turn ing the
formed steel hanger counterclockwise.
➁ Spread the clip assembly apart, place over
the T-irons, and fi rmly squeeze the clip
assembly back to geth er, mak ing sure the
clip is fi rmly seated around the T-iron.
Retighten by using pliers to turn the formed
steel hanger clockwise. Make sure it is fully
tightened.
➂ Se cure with the nut. Tighten with pliers.
Please Note: Make sure the clip is
fully tightened around the T-iron, and
that the formed steel hanger and the
lock nut are fully tightened. Poorly
tightened clip assemblies, hangers
or nuts allow the T-Bar Twist Clip to
work loose.
➃ Test by trying to pull the twist clip open and by pulling down on the hanger.
The clip should not pull open.
➄ Suspend “S” hooks (not included) from the holes in the clips and hook
through holes in the front of the screen mounting brack et. For added safe ty,
crimp both ends of the “S” hooks so the screen can not come off.
Please Note: T–Bar Twist Clips are not rec om mend ed for screens larg er
than 70" x 70" unless T-irons are reinforced.
Crimp
Crimp
Caution
➀ Read and understand these instructions; keep them for future reference.
Follow instructions carefully.
➁ Care in both mounting and correct operation will mean long and satis-
factory service from your Draper screen.
➂ Locate the screen where the audience can best see it, and where other
room fur nish ings permit.
➃ Mount the screen so that the bottom of the picture, when screen is fully
extended, will be above the heads of viewers.
➄ When raising screen, pull down and, while holding, allow for slow
retraction into the case to reduce risk of injury from falling screen.
➅ Screen should be installed level (using a carpenter’s level).
➆ Nothing should be fastened to screen dowel or viewing surface.
NOTE: Screen has been thoroughly inspected and tested at factory and found to
be operating prior to shipment.
Luma
Star
Luma pictured
Clip
Assembly
Screen
Hanger
Nut
Crimp
Crimp
Luma pictured
Viewing Surface Care & Maintenance
Matt White & High Contrast Grey
Clean surface with a solution of mild dishwashing liquid diluted with warm
water. Sponge the surface, rinse with clear water and blot dry. Do not use clean ing
solvents or abrasives.
Glass Beaded
Clean with a very soft brush or cloth and care ful ly dust the surface. DO NOT
USE SOAP, WATER, SOLVENTS OR ABRASIVES. These substances will damage
a glass beaded viewing surface.
Caution: If mounting screen on old-
style metal wall brackets, do not mount
back of screen to front of bracket.
Lip to prevent screen from
“jumping” off mounting screw
Please note: When installing wall brackets, fl exible driver bit extensions may make
it easier to accurately drive the fasteners into the mounting surface.
Produktspezifikationen
| Marke: | Draper |
| Kategorie: | Projektionsleinwand |
| Modell: | Luma |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Draper Luma benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Projektionsleinwand Draper
25 Mai 2024
14 März 2024
16 Dezember 2023
2 Dezember 2023
20 September 2023
5 September 2023
17 August 2023
12 August 2023
14 Juni 2023
14 Juni 2023
Bedienungsanleitung Projektionsleinwand
- Projektionsleinwand Da-Lite
- Projektionsleinwand Sony
- Projektionsleinwand Pyle
- Projektionsleinwand Optoma
- Projektionsleinwand Celexon
- Projektionsleinwand Projecta
- Projektionsleinwand AV:link
- Projektionsleinwand Oregon Scientific
- Projektionsleinwand Duronic
- Projektionsleinwand Luxburg
- Projektionsleinwand EluneVision
- Projektionsleinwand Stewart
- Projektionsleinwand Elite Screens
- Projektionsleinwand Instaal
Neueste Bedienungsanleitung für -Kategorien-
2 Juni 2024
2 Juni 2024
22 Mai 2024
21 Mai 2024
16 Mai 2024