Draper Access FIT V Bedienungsanleitung

Draper Projektionsleinwand Access FIT V

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Draper Access FIT V (8 Seiten) in der Kategorie Projektionsleinwand. Dieser Bedienungsanleitung war für 39 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/8

Contents

Overview - Components .......................................................................................1

Section 1 - Removing Shipping Brackets

(Tab-Tensioned, "V" Surfaces only)

.......2

PLEASE READ - Safety Information ....................................................................2

Section 2 - Hanging Screen .................................................................................3

Section 3 - Bottom Access FIT Panel Installation/Removal ..........................3

Section 4 - Motorized Roller/Fabric Installation ..............................................4

Section 5 - Motorized Roller/Fabric Removal ...................................................4

Section 6 - Operation............................................................................................5

Section 7 - Tab-Tension Adjustment Procedure ..............................................5

Section 8 - Limit Adjustments .............................................................................6

Section 9 - Case Length Dimensions ................................................................. 7

Section 10 - Case Width Dimensions .................................................................7

Section 11 - Mounting Bracket Dimensions......................................................7

Section 10 - Wiring Diagrams: 110-120V Motor and Quiet Motor ..................8

Overview - Components

CAUTION

Read and understand all warnings

(Page 2)

before beginning installation.

Electrical

Cutout

Tab Tensioning

“V” Dowel

“E” Dowel

Mounting Bracket

Mounting Bracket Hoisting Bracket

Leveling Brackets

Hoisting Bracket

“E” Free Hanging

Viewing Surface

“V” Flexible Vinyl

Viewing Surface

Trim Flange

Shipping Brackets Attached

to Dowel and Screen Case

(V Screens Only)

Please Note: Shipping brackets must remain

in place until product has been mounted and

connected to power

(see Sections 1 and 4 in this

document.)

Also, DO NOT operate screen before removing

shipping brackets from screen case.

TOOLS REQUIRED

POW R RILE D L

PENCIL

TAP ASUE E M RE

HAR ARDW E

(b oth rs)y e

L LEVE

Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385

draperinc.com | 765.987.7999 | 800.238.7999

Access FIT E and V

Electric projection screen

INSTRUCTIONS

INSTALLATION & OPERATION

If you have any difﬁculties installing or servicing your

Access FIT screen, call your dealer or Draper, Inc.

PLEASE READ - Safety Information

WARNING

Improper installation and use of the Access Fit E and V screen can result in serious injury or death. Primarily, injuries can occur if the unit falls due to

imprecise installation, mishandling of the unit during installation, or installation on an insufﬁcient wall or ceiling structure. Please use extreme care.

Please read the following installation guidelines thoroughly and follow them

carefully. Failure to do so may cause product to fall or otherwise fail, and could

result in serious injury.

Installation and calibration of the unit should only be performed by an

authorized, qualiﬁed, and experienced professional. In particular, electrical

work and wiring [indicated in diagram by dashed lines] must be completed only

by a qualiﬁed professional electrician who has read this manual completely

and is familiar with the construction and operation of this equipment and the

hazards involved.

Do not afﬁx the unit to walls or ceilings that have inadequate strength

to permanently hold the unit during use. It is the owner’s and installer’s

responsibility to conﬁrm the wall or ceiling to which the unit attaches is

sufﬁcient to permanently hold the weight and stress loads of the unit at all

times. Draper, Inc., is not responsible for improper installation, application,

testing, or workmanship related to the product at place of installation.

It is the installer’s responsibility to make sure appropriate fasteners are used

for mounting.

All hardware must be installed level. Unit must be level and square.

Never leave the area while operating the unit during installation, maintenance,

or normal operation, unless it is secure and safe.

Before testing or operation, carefully inspect the entire area and path

(especially

underneath)

of unit to be sure no persons or objects are in the area.

Turn off power and any nearby equipment or cables carrying electricity before

connecting switches, wires, controls, or electrical components.

Do not wire motors in parallel without written permission from Draper, Inc.

10.

During testing or operation, carefully watch the surrounding area for any

potential safety concerns including nearby persons or objects.

11.

After installation, the entire system, including all sensors, should be carefully

tested to ensure safe and normal operation. Extreme care should be taken

during testing to remain clear of moving parts to avoid possible injury.

12.

Operation of unit should be performed only by authorized and qualiﬁed

personnel, who have been trained in its safe and effective operation and

understand its safety features.

13.

The safety features of the unit should never be disabled, bypassed, or

overridden. The system should not be operated until all safety features are

properly and completely installed, calibrated, and tested.

14.

Unit may need to comply with local, state, or district rules and regulations, in

particular when installed in schools. All applicable rules and regulations should

be reviewed before installation and use.

15.

Failure to precisely follow installation guidelines invalidates all

warranties.

16.

Custom products/installations may not be reﬂected in this manual. Call Draper,

Inc., if you have questions about the installation of custom products or any

questions about your installation.

Before Beginning Installation

Look for any job site conditions that could interfere with installation or

operation of the system.

Read carefully and be sure to understand all installation instructions and

all related operations manuals. These instructions are intended to serve

as a guide for the installer and owner. They should be followed closely and

combined with the expertise of experienced qualiﬁed installers. Draper, Inc., is

not responsible for improper installation, application, testing, or workmanship

related to the product at place of installation. Please retain all instructions for

future use.

Open cartons lengthwise.

Locate and lay out all pieces.

Inspect all boxes to make sure you have received the proper unit and parts.

Controls may be shipped separately, or in same carton as unit.

If you have any difﬁculties with installing, servicing, or operating your unit, call

your dealer or Draper, Inc., 765-987-7999.

Important Safety Information Important Safety Information

Remove

fasteners from

bracket clamps.

Run screen

DOWN to expose

dowel screws.

Loosen screws

and remove

shipping bracket.

Retighten

dowel endcap

screws.

Section 1 - Removing Shipping Brackets

(Tab-Tensioned, "V" Surfaces only)

CAUTION: DO NOT remove shipping

brackets until product has been

mounted and connected to power

(see

Section 4 in this document.)

Also, DO NOT OPERATE SCREEN

BEFORE REMOVING SHIPPING

BRACKETS FROM SCREEN CASE.

page 2 of 8

Access FIT E and V

CENTER of CASE

CENTER

of CASE

Engagement Bracket

With Ball Detent:

will snap into Access

Panel Support Bracket.

Access Panel

Support Bracket

Attaching Brackets:

Insert pin in top

slot and push up.

Rotate bracket

clockwise to lock

bracket in place.

Remove Screws

from both ends

of Screen Housing.

Access

Panel Door:

Pivot on Hinges.

OPEN

ACCESS

PANEL

CLOSED

ACCESS PANEL

SCREEN

HOUSING

Section 3 - Bottom Access FIT Panel Installation/Removal

Figure 3

Access case as seen from below

Bottom Access FIT panel secures to the screen housing

with two screws

(one on each end)

, and held in the closed

position by engagement brackets with ball detents that

snap into case support brackets

(Fig. 3)

CAUTION: For larger sizes, the following requires two people to perform safely.

Bottom ﬂange of

Access housing

Bottom Access Panel Door

CAUTION: Beware of pinch points at ends of closure

Please Note: When locating viewing surface and checking clearance for screen operation, ensure that surface is centered in the case.

Engage each case mounting bracket

(attached to case)

with top of housing

(Fig. 2)

and tighten set screws.

Section 2 - Hanging Screen

Screen should be sufﬁciently supported to withstand

vibration.

Please Note: A hoisting bracket is included on each end of the

case to aid in overhead installation.

Ensure that fasteners are of adequate strength and suitable

for the mounting surface chosen. Supporting hardware

such as chains, cables, two

3/8

(9.5 mm)

rods, etc., must be

precisely vertical.

Entire bottom of case must be readily accessible after

installation is complete.

Front, back, and top of case must be straight—not forced

to warp or bow.

CAUTION: Screen case and ﬂange are not designed to

serve as ceiling support.

Do not seal unit in ceiling until electrical connections have

been made and screen operates successfully.

Please Note: If case is painted on location, removal of roller/

fabric assembly is recommended prior to painting. If not

removed, slot on bottom of case should be shielded to

protect viewing surface from paint splatters/overspray.

HOISTING

BRACKET

CASE

MOUNTING

BRACKET

7⁄8" (22mm)

ELECTRICAL

KNOCKOUT

TYPICAL

INSTALLATION

With typical installation, brackets

may be angled to meet installation requirements.

CASE

MOUNTING

BRACKE TS

ALTERNATE

INSTALLATION

Additional set of brackets

required, but NOT included.

Figure 2

Installation of Case

Figure 4

Removing Access Panel

Press up on Access FIT panel and pull toward the front of the

screen housing to disengage hinges and remove Access FIT panel.

To Remove/Install Support Brackets:

page 3 of 8

Access FIT E and V

Produktspezifikationen

Marke:	Draper
Kategorie:	Projektionsleinwand
Modell:	Access FIT V
Gewicht:	34000 g
Produktfarbe:	Weiß
Befestigungstyp:	Zimmerdecke
Paketgewicht:	41000 g
Natives Seitenverhältnis:	16:9
Gehäusefarbe:	Weiß
Einsehbare Bildschirmhöhe (H):	1140 mm
Einsehbare Bildschirmbreite (B):	2030 mm
Diagonal:	92 "
Antriebstyp:	Motorisiert
Format:	HDTV
Schwarzer Vorlauf:	305 mm
Gehäuse L1:	2720 mm
Bildschirmoberfläche:	Mattweiß
Gespannter Bildschirm:	Ja