Da-Lite Wireline Advantage 29745EG Bedienungsanleitung

Da-Lite Nicht kategorisiert Wireline Advantage 29745EG

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Da-Lite Wireline Advantage 29745EG (12 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/12
INSTRUCTION BOOK FOR
Wireline Advantage®
2
Tools Required for Installation
Important Safety Instructions
When using your video equipment, basic safety precautions
should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so it will not be tripped over, pulled or contact
hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at
least equal to that of the appliance should be used. Cords rated
for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric shock
when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by the
manufacturer may cause a risk of ire, electric shock, or injury to
persons.
6. Do not allow children to play with ixed controls. Keep remote
controls away from children.
7. Frequently examine the installation for imbalance and signs of
wear or damage to cables. Do not use if repair or adjustment is
necessary.
8. Appliance is not to be used by persons, including children, with
reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given
supervision or instruction.
9. Failure to provide adequate structural strength for this
component can result in serious personal injury or damage to
equipment! It is the installer’s responsibility to make sure the
structure to which this component is attached can support the
weight of all equipment. Reinforce the structure as required
before installing the component.
10. Use this projection screen only for its intended use as described
in these instructions. Do not use attachments not
recommended by the manufacturer.
Save These Instructions
1/4", 7/16" and 3/4“
Open Wrench or
Socket Driver
1/8 Hex Key
(included)
Original Instructions
Disclaimer
Milestone and its ailiated corporations and subsidiaries
(collectively "Milestone"), intend to make this manual accurate
and complete. However, Milestone makes no claim that the
information contained herein covers all details, conditions or
variations, nor does it provide for every possible contingency in
connection with the installation or use of this subject to change
without notice or obligation of any kind. Milestone makes no
representation of warranty, expressed or implied, regarding the
information contained herein. Milestone assumes no
responsibility for accuracy, completeness or suiciency of the
information contained in this document.
Da-Lite® is a registered trademark of Milestone AV Technologies.
All rights reserved.
#3 Phillips
Screwdriver
3
1. The case provides multiple attachment Ceiling Mount:
points for bolts, cables, or threaded rod. Page 4 shows
threaded rod installed. The variable position-mounting
bracket may be located anywhere along the length of the
case. It is recommended to keep the brackets spaced evenly
enough to distribute the weight of the screen. One
mounting bracket is required for every 4' of case length.
Wall Mount: For use with optional langeless case only. The
variable position wall mounting brackets (sold separately)
may be located anywhere along the length of the case. It is
recommend to keep the brackets spaced evenly enough to
distribute the weight of the screen. One mounting bracket is
required for every 4' of case length.
2. Tighten bolts until trim lange islush with Ceiling Mount:
ceiling.
Wall Mount: Remove lat brackets from top of case and
discard. Save bolts to attach wall brackets to case. Determine
spacing of wall brackets and attach to wall. Hoist screen to
brackets and completely tighten bolts attaching case to wall
brackets.
NOTE: For proper operation, screen assembly must be level
after installation.
3. Remove the silver shipping brackets that attach the slat to
the screen case. Use the supplied 1/8" hex key to remove the
set screws and a 1/4" socket to remove the screws from the
slat bar.
4. Using a 7/16" wrench and #3 Phillips screwdriver, remove the
shipping bracket that is attached to the roller. Once the
white wire is disconnected, feed it into the junction box in
order to complete the electrical installation. See Figure 1.
NOTE: Depending on the inal postion of the screen roller,
there may be a wood iller block insert for bracket
attachment. The wood block must be removed and
discarded before operation.
Case Installation
Pre-Installation
1. Carefully unpack case from shipping crate.
2. Set aside the Installation Kit. Items inside will be used during
installation.
3. Make sure to recheck measurement of case for proper
installation clearance.
4. Remove any protective foam from case.
5. If necessary, adjust hanger brackets with a 3/4" open wrench
or socket driver.
Remove
Bolt
White (Common)
Wire
Remove
Screw
Figure 1
Case Installation (continued)
5. Remove 2 screws to open junction box. Install electrical
connections that apply to your unit. Make sure to review the
wiring diagram for proper hook up. Replace junction box
cover and secure with 2 screws.
NOTE: Motor Operator Projection Screen Model WAD must
be installed in accordance with the requirements of the
Local Building Codes, the Canadian Electrical Code (CEC),
CAN/CSA C22.1 and the National Electric Code (NEC), NFPA
70. An appropriate disconnect device shall be provided as
part of the building installation.
6. Test installation by running screen up and down a few times.
Be prepared to stop screen should any objects obstruct the
movement of the screen. To prevent damage to the motor,
the standard duty cycle is 2 minute 30 seconds on and 50
minutes of. For 230 volt motors 2 operating cycles is not to
be exceeded.
NOTE: Do not allow upper batten bar to come to a rest on
any object during travel. Doing so will cause cables to lose
tension.
7. The screen comes set standard with 18" of wire drop out of
the case.
Wood
Filler
Block
4
Ceiling Installation
Variable Position
Mounting Brackets
Electrical
Junction Box
Electrical
Junction Box
Screen Roller
Access Door
Audience
Side
Self-Trimming
Flange
(Suggested) 1/2"
Threaded Rod
(Not Included)
Attached to
Mounting Bracket
Finished
Ceiling
Self-Trimming
Flange
12 "
13"
11"
9 ⅛"
11 ⁄"
The Wireline Advantage comes standard with ceiling mount brackets.
5
Wall Installation
Variable Position Wall
Mounting Brackets
(Optional Accessory)
Electrical
Junction Box
Flangeless
Case Option
Recommend
1/2" x 2"L Lag
Screw with 1/2"
Washer
(3 places)
For wall installation, the wall mount brackets must be ordered separately and the Wireline Advantage must be ordered with the
flangeless case option..
18 ¼"
12"
11"
12 ¼"
18"
2 ¼"
1"
7"
7"
1/2"
1 ½"
2"
6
120V Wiring Diagram
Power Input
120VAC / 60Hz
Black (Hot)
White (Common)
Green
(Ground)
Ground
Lug
230V Wiring Diagram
Power Input
230VAC / 50Hz
Brown (Hot)
Blue (Common)
Green/Yellow
(Ground)
Ground
Lug
7
1. Run screen in down direction until it reaches lower limit and
stops.
2. Press and hold both "UP" and "DOWN" arrows simultaneously
until screen jogs.
3. Run screen to new desired lower limit position by pressing
DOWN arrow on remote
NOTE: Motor will run in momentary contact mode while in
this procedure. If you go to far down you can press up and
move to the next step.
4. Press and "MY" (STOP) button until the screen jogs to
conirm new limit.
1. Run screen in down direction until it reaches lower limit and
stops.
2. Press and hold both "UP" and "DOWN" arrows simultaneously
until screen jogs.
3. Run screen to new desired lower limit position by pressing
UP arrow on remote.
NOTE: Motor will run in momentary contact mode while in
this procedure. If you go to far down you can press down
and move to the next step.
4. Press and "MY" (STOP) button until the screen jogs to
conirm new limit.
NOTE: The entire screen surface must be unrolled from the
large roller for proper tensioning.
Screen Travel Adjustment for 120V Screens
More Screen Drop Less Screen Drop
Surface travel is set to stop automatically with 18" of wire travel out of the case. Use the supplied radio frequency remote control to
make adjustments to the amount of travel.
NOTE: For multiple screen installations, disconnect power to every screen except the one being adjusted prior to making changes.
CAUTION: Do not adjust for more than 29' of cable drop.
ATTENTION! Ne pas régler plus de 884 centimètres de chute
de câble
Front of Remote Back of Remote
Pairing an Accessory for 120V Screens
1. On the back of the remote that shipped with the screen,
press and hold the program button until the motor jogs.
2. On the accessory being paired, press and hold the program
button until the motor jogs.
3. The accessory is now paired with the screen.
PROG - FC


Produktspezifikationen

Marke: Da-Lite
Kategorie: Nicht kategorisiert
Modell: Wireline Advantage 29745EG

Brauchst du Hilfe?

Wenn Sie Hilfe mit Da-Lite Wireline Advantage 29745EG benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Da-Lite

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-