Da-Lite NET-100 Bedienungsanleitung


Lesen Sie kostenlos die ๐Ÿ“– deutsche Bedienungsanleitung fรผr Da-Lite NET-100 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fรผr 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
INSTALLATION GUIDE FOR
Da-Lite NET๎˜Ÿ100
2
When connecting the NET๎˜Ÿ100, there are three connections that
must be made to the SCB๎˜Ÿ100 for proper operation: Power
+12Vdc, RS๎˜Ÿ232 Communication and Ethernet.
NOTE: If you ordered your screen with a built-in SCB๎˜Ÿ100 it will
come equipped with a 11-pin phoenix connector. The NET๎˜Ÿ100 will
be equipped with a 2-pin plug and 3-pin plug for connection. The
2-pin plug will plug into #10 and #11 and the 3-pin plug will plug
into #4, #5 and #6. (See Fig. 1)
Product Description
The NET๎˜Ÿ100 is an Ethernet adapter to the SCB๎˜Ÿ100 Serial Control Board for Da-Lite motorized screens and projector lifts. This Ethernet
adapter allows remote control of a screen or lift through a TCP/IP connection.
The NET๎˜Ÿ100 is classi๎˜žied as a serial device server, which by de๎˜žinition means that it makes available to client computers the Da-Lite
screen or lift as a serial device (enabled by the SCB๎˜Ÿ100). The NET๎˜Ÿ100 supports the suite of RS๎˜Ÿ232 commands developed under the
SCB๎˜Ÿ100, and allows those commands to be issued by an Ethernet enabled computer or third party controller.
Installation
Figure 1
Terminal
Block
3๎˜ŸPin Plug
RS๎˜Ÿ232 Communication
2๎˜ŸPin Plug
+12VDC Output
If you did not order your screen with a built-in SCB๎˜Ÿ100, remove the 2-pin and 3-pin connectors from the NET๎˜Ÿ100. Refer to (Fig. 2)
Once these connections have been made and power
is supplied to the SCB๎˜Ÿ100, the NET๎˜Ÿ100 will be
powered from the SCB๎˜Ÿ100.
Upon a successful connection, the power LED and
the status LED will turn on solid green. The green
10/100 Mb Link LED indicates the presence of
communication between the NET๎˜Ÿ100 and
one or more nodes on the network.
Power II IPut
120VAC / 60Hz
Back Of
Wall Switch
Red (Tx)
Black (Rx)
Green (Ground)
Front Of
Wall Switch
NOTE: 20๎˜Ÿ24AWG Wire
Recommended For Connecting
Wall Switch To The SCB๎˜Ÿ100
Controller
RJ๎˜Ÿ45 Connector
RJ๎˜Ÿ45 Ethernet
Connection
Black With White
Stripe 12VDC+
Black Solid
12VDC -
DB๎˜Ÿ25 to RJ๎˜Ÿ45
Adaptor
Strain Relief
Black (Hot)
Green (Ground)
White (Common)
Black (Hot)
Green (Ground)
White (Common)
+ 120 VDC OUT
Red Up
Black (Down)
White (Common)
Red (Up)
Black (Down)
White (Common)
Rx - Data In
G - Ground
TX - Data Out
RX - Data In
G - Ground
Tx - Data Out
WBR
- 120 VDC OUT
Up
Stop
Down
RJ๎˜Ÿ45 PINOUT
PIN - 3 RX
PIN - 4 TX
PIN - 5 GR
PIN - 6 NOT USED
Figure 2
3
Con๎˜žiguration
The NET๎˜Ÿ100 is designed for simple, transparent installation and
con๎˜žiguration. By default the NET๎˜Ÿ100 is shipped with DHCP
disabled. The following IP address is assigned to the NET๎˜Ÿ100.
IP Address: 192.168.1.100
Subnet: 255.255.255.0
To con๎˜žigure the network settings, type the IP address into your
browser. It will open a new page with the setup pro๎˜žile. A new
window will pop up asking for a user name and password. Leave
the user name and password ๎˜žield blank and press the OK
button.
The new window will contain the con๎˜žiguration browser program.
The menu will be located on the left side of page. Click on
"Network".
For DHCP click on "Obtain IP address automatically" and type in
the DHCP HostName. For Static IP leave the option "Use the
following IP con๎˜žiguration" clicked and type in the IP address and
Subnet Mask. Then click the "OK" button. Finally click on the
"Apply Settings" in the left menu.
Network Menu
OK Button
Blank
OK Button
Apply Settings


Produktspezifikationen

Marke: Da-Lite
Kategorie: Nicht kategorisiert
Modell: NET-100

Brauchst du Hilfe?

Wenn Sie Hilfe mit Da-Lite NET-100 benรถtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Da-Lite

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fรผr -Kategorien-