Da-Lite 99622 Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr Da-Lite 99622 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 9 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: 574-267-8101
800-622-3737
Fax: 574-267-7804
Toll Free Fax: 877-325-4832
www.da-lite.com
e-mail: info@da-lite.com
POWER
PRESENTATION PRODUCTS
The
In
Installation Instructions for
VIDEO PROJECTOR INTERFACE
CAUTION: THE PROJECTOR MUST BE TURNED OFF BEFORE CONNECTING THE TRIGGER WIRES TO THE PROJECTOR. FAILURE
TO DO SO MAY DAMAGE THE CONTROLLER.
1. Use 2-conductor 20-24 gauge wire to extend the low voltage connection from the projector’s 5 or 12-volt screen
trigger output to the length required to reach the VPI. When extending the low voltage connection from the
projector’s screen trigger output, be sure to maintain the proper polarity. the red wire from the VPI is the “signal”
and the black wire from the VPI is the “ground”.
2. Connect the wires from the VPI that are labeled “Low Voltage Connection” to the end of the extended screen
trigger wires above. See Figure 1.
CAUTION: NEVER APPLY VOLTAGE TO THE PROJECTOR’S SCREEN TRIGGER WIRES OR THE VPI AND/OR PROJECTOR WILL BE
DAMAGED.
VIDEO PROJECTOR INTERFACE INSTALLATION
1
The Video Projector Interface (VPI) housing is divided into three compartments. The compartment labeled “Low Voltage
Connections” is where you will connect the VPI to the projector’s output and wall switch wire connections. The
compartment labeled “AC Power Connections” is where the main power and motor wire connections are made. Access
is not required to the center compartment.
WARNING: TO PREVENT ELECTRICAL SHOCK OR DAMAGE TO THE VIDEO PROJECTOR INTERFACE (VPI), DO NOT APPLY
POWER TO THE VPI UNTIL ALL CONNECTIONS ARE COMPLETE. MAKE SURE POWER IS TURNED OFF ON ALL CIRCUITS
BEFORE MAKING CONNECTIONS.
CAUTION: ANY ITEM BEING CONNECTED TO THE VPI CANNOT BE ENERGIZED.
â–˛
!
LOW VOLTAGE CONNECTION
RED
BLACK
RED
BLACK
5/12 VOLT SCREEN
TRIGGER ON
PROJECTOR
5/12 VOLT SCREEN
TRIGGER ON
PROJECTOR
RECOMMENDED WIRE SIZE: 20-24 AWG RECOMMENDED WIRE SIZE: 20-24 AWG
FIGURE 1
120V 240V
â–˛
!
â–˛
!
â–˛
!
2
Screen Motor
1. Using 4-conductor, 14-18 gauge wire, extend the motor wires from the screen junction box to the length required
to reach the VPI.
2. Connect the extended wires from the screen motor to the VPI wires that are labeled “motor wires”. Refer to
Figure 2.
AC POWER CONNECTIONS
GREEN
W
W
W
WWH
H
H
HHI
I
I
IIT
T
T
TTE
E
E
EE
BLACK GROUND LUG
FIGURE 2
POWER
SOURCE
120VAC
60HZ
W
W
W
WWH
H
H
HHI
I
I
IIT
T
T
TTE
E
E
EE
(COMMON)
BLACK (HOT)
GROUND LUG
FIGURE 3
AC Power Source
1. Connect the incoming power wires to the VPI wires that are labeled “AC power input”.
2. Connect the building ground wire to the ground lug on the metal housing. Refer to Figure 3.
RECOMMENDED WIRE SIZE: 14-18 AWG
SCREEN
MOTOR
GREEN/YELLOW
BLUE
BROWN GROUND LUG
RECOMMENDED WIRE SIZE: 14-18 AWG
SCREEN
MOTOR
W
W
W
WWH
H
H
HHI
I
I
IIT
T
T
TTE
E
E
EE
(COMMON)
BLACK (HOT)
GREEN (GROUND)
RECOMMENDED WIRE SIZE: 14-18 AWG
POWER
SOURCE
220VAC
50HZ
BLUE (COMMON)
BROWN (HOT)
GROUND LUG
BLUE (COMMON)
BROWN (HOT)
GREEN/YELLOW (GROUND)
RECOMMENDED WIRE SIZE: 14-18 AWG
120V 240V
120V 240V
RED BLACK
GREEN (GROUND)
GREEN/YELLOW (GROUND)


Produktspezifikationen

Marke: Da-Lite
Kategorie: Nicht kategorisiert
Modell: 99622

Brauchst du Hilfe?

Wenn Sie Hilfe mit Da-Lite 99622 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Da-Lite

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-