Da-Lite Tensioned Large Advantage Electrol 37022L Bedienungsanleitung

Da-Lite Projektionsfläche Tensioned Large Advantage Electrol 37022L

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Da-Lite Tensioned Large Advantage Electrol 37022L (12 Seiten) in der Kategorie Projektionsfläche. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Download PDF

Seite 1/12

INSTRUCTION BOOK FOR

Tensioned Large

Advantage® Electrol®

Tools Required for Installation

1. The case provides multiple attachment points for bolts,

cables, or threaded rod. Page 4 shows threaded rod

installed. The variable position-mounting bracket may be

located anywhere along the length of the case. It is

recommended to keep the brackets spaced evenly enough

to distribute the weight of the screen. One mounting bracket

is required for every 4' of case length.

2. Tighten bolts until trim lange is lush with ceiling.

NOTE: For proper operation, screen assembly must be level

after installation.

3. Remove 2 screws to open junction box. Install electrical

connections that apply to your unit. Make sure to review the

wiring diagram for proper hook up. Replace junction box

cover and secure with 2 screws.

NOTE: Please Note: Motor Operator Projection Screen

Models LADT, LADDT, LAD and LADD must be installed in

accordance with the requirements of the Local Building

Codes, the Canadian Electrical Code (CEC), CAN/CSA C22.1

and the National Electric Code (NEC), NFPA 70. An

appropriate disconnect device shall be provided as part of

the building installation.

If your case was ordered in advance of the screen and roller

assembly, your installation is now complete. Continue to

step 4 if your Tensioned Large Advantage Electrol was

ordered as a complete unit.

4. Carefully remove paper and tape from roller assembly

CAUTION! Do not use a knife or sharp object to cut tape;

you will damage the screen. Pull orange string.

ATTENTION! Ne coupez pas le ruban adhésif sur la toile

avec un couteau ou un outil tranchant. Retirez à la main.

5. Use supplied 1/8" hex key to remove silver shipping brackets

attached to slat and screen case.

6. Test installation by running screen up and down a few times.

Be prepared to stop screen should any objects obstruct the

movement of the screen. To prevent damage to the motor,

the standard duty cycle is 1 minute on and 3 minutes of.

Case Installation

Important Safety Instructions

When using your video equipment, basic safety precautions

should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled,

or contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rating

at least equal to that of the appliance should be used. Cords

rated for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric

shock when the appliance is used subsequently.

5. The use of an accessory attachment not recommended

by the manufacturer may cause a risk of ire, electric shock,

or injury to persons.

Pre-Installation

1. Carefully unpack case from shipping crate.

2. Set aside the Installation Kit. Items inside will be used during

installation.

3. Make sure to recheck measurement of case for proper

installation clearance.

4. Remove any protective foam from case.

5. If necessary. adjust hanger brackets with a 3/4" open wrench

or socket driver.

3/4“ Open Wrench

or Socket Driver

1/8“ Hex Key

(included)

If your screen was shipped with the motor and roller already installed proceed to step 7.

1. Remove the access door. First, remove the 2 bolts from each

end with a 9/16" open wrench or socket driver. Next, use a 5/32"

hex key to remove the two screws in the center of the access

door. This will allow the door to drop open on the hinges

(Figure 1).

2. Carefully unpack screen and roller assembly. Use supplied 1/8"

hex key to remove shipping brackets attached to slat. Remove

fabric and roller assembly from shipping board using a 1/2"

wrench. Leave packing paper on roller.

3. Remove the square peg bracket from the motor end of the

roller assembly (Figure 2).

4. Remove the safety clip from the motor attachement bracket

located in the motor end of the screen housing.

5. Use a 1/2" open wrench or socket driver to loosen the four

bolts that secure pin end mounting bracket into housing. Lift

pin end of roller into position and slide the bracket into the

roller pin. Tighten all four bolts. Slide the pin end bracket

towards the end of the case (Figure 3).

6. Place the roller assembly into the case with the motor on the

left side. The limit switches should be facing down. Line up the

head of the motor with the motor attachment bracket.

7. Complete electrical hook-up by snapping motor 1/3 wire

connectors into case connectors (Figure 2).

8. Return to motor end and insert safety clip over casting bracket

to secure motor end.

9. Carefully remove tape strips securing picture surface around

roller. Slat should move freely. (Only if the roller assembly is pre

installed.)

CAUTION! Do not cut tape on fabric with a knife or any

sharp tool. Remove by hand.

ATTENTION! Ne coupez pas le ruban adhésif sur la toile

avec un couteau ou un outil tranchant. Retirez à la main.

10. Test installation by running screen up and down a few times.

Be prepared to stop screen should any objects obstruct the

movement of the screen. To prevent damage to the motor, the

standard duty cycle is 1 minute on and 3 minutes of.

11. Re-install the access door. Procedure is the reverse of step 1

listed above.

Screen And Roller Assembly Installation

Tools required for screen and roller assembly:

Bolts

Figure 3Figure 1 Figure 2

Bolts

Access

Door

Door Support

Screws

Screen Motor

LVC Control Box

Screen Motor

Limit Switches

9/16“ Open Wrench

or Socket Driver

1/2“ Open Wrench

or Socket Driver

5/32“ Hex Key 1/8“ Hex Key

(included)

Produktspezifikationen

Marke:	Da-Lite
Kategorie:	Projektionsfläche
Modell:	Tensioned Large Advantage Electrol 37022L

Brauchst du Hilfe?

Wenn Sie Hilfe mit Da-Lite Tensioned Large Advantage Electrol 37022L benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten

Ihren Namen*

Deine E-Mail*

Schreiben Sie hier Ihre Frage