KHOMO GEAR GER-1273 Bedienungsanleitung
KHOMO GEAR
Projektionsfläche
GER-1273
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für KHOMO GEAR GER-1273 (2 Seiten) in der Kategorie Projektionsfläche. Dieser Bedienungsanleitung war für 16 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/2
To ensure the performance of your screen, please note the following points:
1. When installing the screen, find a floor or counter top of the correct size. It's best to cover it with a clean
cloth sheet or another soft material so the screen does not get damaged.
2. Do not write or mark the screen or the frame.
3. Do not use sharp or hard objects on the screento avoid scratches or damage.
4.Avoid touching the white part of the screenwith your hands.
5. Do not use a corrosivedetergent to clean the screen. For cleaning use a soft clean cloth to remove dust.
6. During installation, please take it lightly and keep children away.
7. For this assembly it's recommended to have two people involved
Parts Included:
Side Frame x2
Top & Bottom Frame x4
Center Support Bar x2
Long & Short Fiberglass Rod x4
Screen x1
Corner Joint
Plate x4
Spring Hook
x1
Springs
x100
Hanging Bracket
x4
Joint Plates Screws
x24
Wall Anchors
x8
Wall Screws
x8
Center Joint
Plate x2
1. Place the frames facing down onto the floor or (as the image ), and screw the center
plates into place by using the plate screws.
2. After assembling the top and bottom frames, securely fasten the side frame with
corner plates using the designated screws to ensure a stable structure.
4. Place the screen with the white side facing down on top of the facing down frame to
hook the springs. Start by placing the spring in the middle part of the screen (3-4 on
each side ), pulling them toward the frame.
5. Continue to hook the corner springs toward the frame, then complete the remaining
springs until the screen is completely stretched out.
7. Measure the area where the projector screen is going to be hung. Install the brackets
at the least 50-inch apart, and make sure there are aligned. Use a power drill to make
the holes. Insert the anchors then place the brackets and screws into place. 8. Hang your projector screen and Enjoy!
3. For this step we recommend washing your hands, avoid touching the white side of the
screen, and use a clean cloth sheet underneath. Roll out the projector screen with the
black side facing up, and slide the fiberglass rods into the four side pockets of the
screen.
Instructional Video
6. Start by positioning the support bars into the top groove on the back of the frame.
Then, working together, gently extend the bottom frame outward while ensuring the
support bar is centered before securing it into place.
Top
Bottom
Produktspezifikationen
| Marke: | KHOMO GEAR |
| Kategorie: | Projektionsfläche |
| Modell: | GER-1273 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit KHOMO GEAR GER-1273 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Projektionsfläche KHOMO GEAR
4 September 2024
4 September 2024
Bedienungsanleitung Projektionsfläche
- Projektionsfläche Da-Lite
- Projektionsfläche Pyle
- Projektionsfläche Optoma
- Projektionsfläche Kodak
- Projektionsfläche NEC
- Projektionsfläche Celexon
- Projektionsfläche Elite
- Projektionsfläche AV:link
- Projektionsfläche Draper
- Projektionsfläche Oregon Scientific
- Projektionsfläche Duronic
- Projektionsfläche GPX
- Projektionsfläche Luxburg
- Projektionsfläche EluneVision
- Projektionsfläche Stewart
- Projektionsfläche Elite Screens
- Projektionsfläche Lumene
- Projektionsfläche Avers
- Projektionsfläche Elite ProAV
- Projektionsfläche EPV
Neueste Bedienungsanleitung für -Kategorien-
12 Oktober 2024
2 Oktober 2024
29 September 2024
27 September 2024
20 September 2024
11 September 2024
7 September 2024
6 September 2024
6 September 2024
5 September 2024