Draper Luma 207008 Bedienungsanleitung
Draper
Projektionsfläche
Luma 207008
Lesen Sie kostenlos die đ deutsche Bedienungsanleitung fĂźr Draper Luma 207008 (1 Seiten) in der Kategorie Projektionsfläche. Dieser Bedienungsanleitung war fĂźr 11 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/1
Crimp
Crimp
Luma pictured
Operating InstructionsâStandard
To lower picture surface, pull screen down. âthen allow screen to Hesitate
retract very slowly until it locks in place.
To raise picture surface, pull screen down and, while holding, allow for
slow retraction into the case to reduce risk of injury from falling screen.
Operating InstructionsâAutoReturn (Available with Luma)
To lower picture surface, pull screen down. âthen allow screen to Hesitate
retract very slowly until it locks in place.
To raise picture surface, pull screen down gently (1-3 inches), then release.
Wall Mounting
(Hardware not Included)
Ceiling Suspended
(Hardware not Included)
TâBar Twist Clips
(Optional Equipment)
Extension Brackets
(Optional Equipment)
If you encounter any difďŹ culties installing or servicing your screen, call your dealer
or Draper, Inc., Spiceland, Indiana, (765) 987-7999, or fax (765) 987-7142.
Copyright Š 2008 Draper Inc. Form Luma-Star_Inst08-R4 Printed in U.S.A.
Installation/Operating Instructions
Luma and Star Spring Roller Operated Projection Screens by Draper
Installation
Your Draper screen can be mounted on a wall or suspended from the ceiling or
extension brackets. It must be mounted level and with the ďŹ at back parallel to the
wall.
The screen (or extension brackets) should be mounted into studs or blocking in the
wall/ceiling, or in drywall (minimum thickness ½") with speciďŹ ed anchors. For any
other type of installation, follow all local build ing and safety codes.
Steel studs, concrete or cinder block walls and all other types of non-wood frame
construction require the use of special screws or anchors.
The selection of ap pro pri ate mounting hardware should be made by a
qualiďŹ ed professional installer.
Use the upper portion of the holes at the back of the endcap/mounting bracket
for ďŹ ush wall mount ing. Recommended hard ware (not included): For mount ing
into wood or wall stud, use #10 x 1Âź" wood screws; for mount ing into dry wall
(minimum ½" thick), use 3/16" tog gle bolts or 3/16" molly bolts. DO NOT USE FLAT
HEAD SCREWS. DO NOT OVERTIGHTEN.
Use the holes at the front of the endcap/
mount ing brack et for sus pend ed mount ing.
Po si tion and prop er ly an chor screw eyes or
oth er fasteners (not included) into ceil ing
joists or oth er sol id sur face. Sus pend âSâ
hooks (not included) from fas ten ers (not
included) and hook through holes in the
front of the mount ing brack et. For added
safe ty, crimp both ends of the âSâ hooks so
the screen can not come off.
Recommended hardware (not included):
For mount ing into wood or ceil ing joist,
use two
3
/
16
" x 1
1
/
4
" screw eyes and
3
/
16
"
di am e ter âSâ hooks; for mount ing into
dry wall (min i mum
1
/
2
" thick), use
3
/
16
" tog gle
or molly bolts with
3
/
16
" âSâ hooks.
Wall mount the brackets (not in clud ed
with screen) using hard ware recom-
mended for âWall Mountingâ (above, not
included). Then, sus pend the screen from
the front holes with âSâ hooks. For added
safe ty, crimp both ends of the âSâ hooks
so the screen can not come off.
DO NOT OVERTIGHTEN.
ÂŽ
â Loosen the clip assembly by turn ing the
formed steel hanger counterclockwise.
â Spread the clip assembly apart, place over
the T-irons, and ďŹ rmly squeeze the clip
assembly back to geth er, mak ing sure the
clip is ďŹ rmly seated around the T-iron.
Retighten by using pliers to turn the formed
steel hanger clockwise. Make sure it is fully
tightened.
â Se cure with the nut. Tighten with pliers.
Please Note: Make sure the clip is
fully tightened around the T-iron, and
that the formed steel hanger and the
lock nut are fully tightened. Poorly
tightened clip assemblies, hangers
or nuts allow the T-Bar Twist Clip to
work loose.
â Test by trying to pull the twist clip open and by pulling down on the hanger.
The clip should not pull open.
â Suspend âSâ hooks (not included) from the holes in the clips and hook
through holes in the front of the screen mounting brack et. For added safe ty,
crimp both ends of the âSâ hooks so the screen can not come off.
Please Note: TâBar Twist Clips are not rec om mend ed for screens larg er
than 70" x 70" unless T-irons are reinforced.
Crimp
Crimp
Caution
â Read and understand these instructions; keep them for future reference.
Follow instructions carefully.
â Care in both mounting and correct operation will mean long and satis-
factory service from your Draper screen.
â Locate the screen where the audience can best see it, and where other
room fur nish ings permit.
â Mount the screen so that the bottom of the picture, when screen is fully
extended, will be above the heads of viewers.
â When raising screen, pull down and, while holding, allow for slow
retraction into the case to reduce risk of injury from falling screen.
â
Screen should be installed level (using a carpenterâs level).
â Nothing should be fastened to screen dowel or viewing surface.
NOTE: Screen has been thoroughly inspected and tested at factory and found to
be operating prior to shipment.
Luma
Star
Luma pictured
Clip
Assembly
Screen
Hanger
Nut
Crimp
Crimp
Luma pictured
Viewing Surface Care & Maintenance
Matt White & High Contrast Grey
Clean surface with a solution of mild dishwashing liquid diluted with warm
water. Sponge the surface, rinse with clear water and blot dry. Do not use
clean ing solvents or abrasives.
Glass Beaded
Clean with a very soft brush or cloth and care ful ly dust the surface. DO
NOT USE SOAP, WATER, SOLVENTS OR ABRASIVES. These substances
will damage a glass beaded viewing surface.
Caution: If mounting screen on old-
style metal wall brackets, do not mount
back of screen to front of bracket.
Lip to prevent screen from
âjumpingâ off mounting screw
Please note: When installing wall brackets, ďŹ exible driver bit extensions may make
it easier to accurately drive the fasteners into the mounting surface.
Produktspezifikationen
| Marke: | Draper |
| Kategorie: | Projektionsfläche |
| Modell: | Luma 207008 |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Draper Luma 207008 benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Projektionsfläche Draper
7 September 2024
5 September 2024
3 August 2024
2 August 2024
2 August 2024
2 August 2024
1 August 2024
31 Juli 2024
31 Juli 2024
29 Juli 2024
Bedienungsanleitung Projektionsfläche
- Projektionsfläche Da-Lite
- Projektionsfläche Pyle
- Projektionsfläche Optoma
- Projektionsfläche Kodak
- Projektionsfläche NEC
- Projektionsfläche Celexon
- Projektionsfläche Elite
- Projektionsfläche AV:link
- Projektionsfläche Oregon Scientific
- Projektionsfläche Duronic
- Projektionsfläche GPX
- Projektionsfläche Luxburg
- Projektionsfläche EluneVision
- Projektionsfläche Stewart
- Projektionsfläche Elite Screens
- Projektionsfläche Lumene
- Projektionsfläche Avers
- Projektionsfläche Elite ProAV
- Projektionsfläche KHOMO GEAR
- Projektionsfläche EPV
Neueste Bedienungsanleitung fĂźr -Kategorien-
12 Oktober 2024
2 Oktober 2024
29 September 2024
27 September 2024
20 September 2024
11 September 2024
6 September 2024
6 September 2024
5 September 2024
4 September 2024