Da-Lite Cinema Contour 20387V Bedienungsanleitung
Da-Lite
Projektionsfläche
Cinema Contour 20387V
Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Da-Lite Cinema Contour 20387V (8 Seiten) in der Kategorie Projektionsfläche. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet
Seite 1/8
INSTRUCTION BOOK FOR
Cinema Contour® Screen
2
High Power® Frame Bracket
Screens with High Power® quantity = 2
Screens with 2-piece side frame rails quantity = 2
Quantity Included ___________________________
Included Hardware
Frame Assembly
1. Unwrap the frame pieces. Assemble frame pieces on padding
material or other soft, clean surface. This will help keep the
frame clean and protect it from scratches.
2. Slide the frame pieces together at corners (Note: Frame
assembly holes may not appear to it properly at the corners
until all fasteners have been attached. Once fasteners are
attached, the frame corners will be drawn in for a proper it.)
Secure frame pieces with #10 screws provided. Do not tighten
screws until all are started, then tighten. See Figure 1.
NOTE: The frame pieces are labeled “top” and “bottom”. Be
sure the frame pieces are assembled according to the labels.
This will ensure the snap pattern on the frame and screen
surface will match.
3. Attach the eight snap studs to the back of the frame in the
predrilled holes.
Figure 1 (Rear View)
Large Wall Bracket (47" Long)
Installation screws not included
Quantities vary by screen size:
Screens 80" and smaller viewing width = 1
Screens over 80" to 96" viewing width = 2
Screens over 96" viewing width = 3
Quantity Included ___________________________
Small Wall Bracket (8" Long)
Installation screws not included
Quantity = 1. Only for screens 80" and smaller viewing width.
Quantity Included ___________________________
Snap Stud
Quantity Included ___________________________
#10 Screw
Quantity Included ___________________________
Use Installation Method Number ____________
Screws
Snaps
3
Installation
Method 1 (Screens 80" And Smaller
In Viewing Width)
Method 1 (Screens 80" And Smaller
In Viewing Width)
There are four methods of installation based on the size of the
screen and type of viewing surface. Measure the width of the
viewing area of your screen and refer to the appropriate method
of installation below. The wall bracket diagram shows the type
and quantity of bracket(s) supplied based on the size of the
screen.
Method 1: Screens 80" and smaller in viewing width.
Method 2: Screens over 80" up to 96" in viewing width.
Method 3: Screens over 96" in viewing width.
Method 4: Any size screen with High Power® viewing surface.
1. Secure the wall bracket to wall studs at the desired height.
Make sure the bracket is level. The top of the frame will be
1/8" above the top of the wall bracket when mounted. You will
need at least 5/8" clearance above the bracket to hang the
screen. Figures 2, 3, and 4 show the proper orientation for the
supplied wall brackets.
2. To install the lower wall bracket, you must measure the
overall height of the screen frame and subtract 1-3/8". Using
that dimension, measure down from the top edge of the wall
bracket and mark the wall for two screw holes. The holes
should be centered within the frame and 6" apart. Refer to
Figure 3.
3. Attach the small wall bracket to the wall. Refer to Figure 4 for
proper orientation. Do not tighten the screws completely. The
bracket should slide up and down easily.
4. Unroll the screen on a clean surface. Do not use newspaper.
The viewing side is rolled to the inside of the roll. Place the
frame over the screen surface, and while lifting the frame
with one hand, snap the screen surface onto the frame
with the other hand while maintaining a steady pull
on the surface.
5. Hang the screen on the brackets by hooking the bottom of
the frame onto the lower wall bracket and lift up until you can
hook the top of the frame on the top bracket. Push down on
the frame to seat it on the brackets. Refer to Figure 4.
Figure 2
Small Wall Bracket
1-Piece
Figure 3
Large Wall
Bracket
1-Piece
Large Wall Bracket
6"
Small Wall Bracket
Overall Height Less 1 ⅜"
Overall
Height
Figure 4
2
Lift
1
3
Wall
Produktspezifikationen
| Marke: | Da-Lite |
| Kategorie: | Projektionsfläche |
| Modell: | Cinema Contour 20387V |
Brauchst du Hilfe?
Wenn Sie Hilfe mit Da-Lite Cinema Contour 20387V benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten
Bedienungsanleitung Projektionsfläche Da-Lite
2 Oktober 2024
27 September 2024
11 September 2024
5 September 2024
2 September 2024
1 September 2024
31 August 2024
17 August 2024
10 August 2024
10 August 2024
Bedienungsanleitung Projektionsfläche
- Projektionsfläche Pyle
- Projektionsfläche Optoma
- Projektionsfläche Kodak
- Projektionsfläche NEC
- Projektionsfläche Celexon
- Projektionsfläche Elite
- Projektionsfläche AV:link
- Projektionsfläche Draper
- Projektionsfläche Oregon Scientific
- Projektionsfläche Duronic
- Projektionsfläche GPX
- Projektionsfläche Luxburg
- Projektionsfläche EluneVision
- Projektionsfläche Stewart
- Projektionsfläche Elite Screens
- Projektionsfläche Lumene
- Projektionsfläche Avers
- Projektionsfläche Elite ProAV
- Projektionsfläche KHOMO GEAR
- Projektionsfläche EPV
Neueste Bedienungsanleitung für -Kategorien-
12 Oktober 2024
29 September 2024
20 September 2024
7 September 2024
6 September 2024
6 September 2024
5 September 2024
4 September 2024
4 September 2024
Celexon Ultramobile Plus Professional 194 x 146 Bedienungsanleitung
3 September 2024