Da-Lite Scenic Roller 40365 Bedienungsanleitung

Da-Lite Nicht kategorisiert Scenic Roller 40365

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Da-Lite Scenic Roller 40365 (4 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/4
INSTRUCTION BOOK FOR
Scenic Roller
2
Pre-Installation Installation
Having decided on hooks, chains, cables or other mounting
method, have mounting prepared before opening box.
Do not mount screen against walls that might rub fabric.
1. Remove screen from box by lifting roller at the ends. Be
careful not to permit lid or any tools to fall on screen. During
installation handle unit only by ends of roller and top header.
Do not grasp around fabric do not rest unit on fabric.
2. Remove wrapping paper and unwind ropes.
3. With the screen lying on the loor, install the clamps on the
reinforcement tape on the header as shown in Figure 2.
Clamp assembly is shown in Figure 1. Drop the closed loop of
the turnbuckle in the slot of the clamp before inserting bolt.
Each clamp uses three bolts and nuts. Do not tighten nuts
any more thaninger tight. Make sure the ends of clamps do
not push into the fabric. Pulleys at each end of header must
be in the vertical position, when hung for proper operation.
4. Adjust top header in fabric pocket to the 21/4" and 33/4"
position shown on the drawing.
5. Hang the screen in place at three, ive, or seven points.
CAUTION! When this screen is shipped from the factory,
there are 2-1/2 turns of rope around each end of the roller.
Make certain that this is left unchanged to insure good
operation.
CAUTION! Before dropping fabric make certain ropes
at end of bottom roller do not overlap. Overlapping of
ropes will cause rope to work inward and thus damage
the fabric.
Figure 1 – Clamp Assembly
3
1. Lower screen slowly by gradually releasing ropes.
2. With screen in the Down” position, turn the header in the
fabric pocket carefully to adjust the pulleys to a vertical end
position. Check the 21/4" and 33/4" end tube dimensions.
Adjust the clamps on the reinforcement tape. Clamps are not
to push into fabric pocket. Tighten nuts on all bolts.
3. Total screen drop may be controlled by adjusting rope clamp.
Do not adjust for more drop.
4. With unit in completely unrolled position, examine the screen
carefully. If slight sag appears in center of fabric, adjust
turnbuckles at the eye bolts until fabric hangs lat.
5. Screen may be raised by pulling on ropes. Tie of ropes to
keep screen in raised position.
6. Protect your screen against damage and it will give many
years of enjoyment.
a. When lowering screen, do so gently. Never allow it to
drop uncontrolled.
b. Before raising screen, be sure both front and back sides
are free from insects or any foreign matter.
c. Form the habit of looking in space between fabric and
roller for foreign matter before raising screen.
d. Caution stage hands and others to avoid bumping
screen with ladders, scenery, etc.
Screen Adjustment
Don't Adjust
Rope Clamp
Already Set
for Proper
Full Screen
Opening
Mount Header
Tube Level
Locate Clamps on
Reinforcement Tape
Mount at These Points Only
Turnbuckle Adjust
for Flat Fabric Hang
Do Not Handle Unit by
Fabric Area
Pulley Must be Installed
in The Vertical Position
Check Here for Foreign
Matter Before Raising
Screen
Center Line of Screen
Handle Unit Only
by Top Header and
Roller Ends During
Installation
Figure 2
2 ¼" 3 ¾"
6" 6"


Produktspezifikationen

Marke: Da-Lite
Kategorie: Nicht kategorisiert
Modell: Scenic Roller 40365

Brauchst du Hilfe?

Wenn Sie Hilfe mit Da-Lite Scenic Roller 40365 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Da-Lite

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-