Da-Lite Pro Imager Vertical Masking System Bedienungsanleitung

Da-Lite Projektionsfläche Pro Imager Vertical Masking System

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Da-Lite Pro Imager Vertical Masking System (8 Seiten) in der Kategorie Projektionsfläche. Dieser Bedienungsanleitung war für 19 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
DA-LITE SCREEN COMPANY, INC.
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
Phone: 574-267-8101
800-622-3737
Fax: 574-267-7804
www.da-lite.com
e-mail: info@da-lite.com
POWER
PRESENTATION PRODUCTS
The
In
Instruction Book for
PRO IMAGER
IMPORTANT SAFETY INSTRUCTIONS
When using your video equipment, basic safety precautions
should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled,
or contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rat-
ing at least equal to that of the appliance should be used.
Cords rated for less amperage than the appliance may over-
heat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric
shock when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by
the manufacturer may cause a risk of fire, electric shock, or
injury to persons.
SAVE THESE INSTRUCTIONS
1
FRAME ASSEMBLY
2
TOOLS REQUIRED FOR ASSEMBLY
5/16" socket or wrench
Carpenters level
Tape Measure
1. Unpack frame pieces and lay them face down on
the floor. The top frame has the roller and motor
assembly attached to it. The side frames are the
two short pieces.
2. Attach the side frame pieces to the top frame.
See figure 1. Insert the slat bar into the small
channel located on the side frame. Fasten the
frame pieces with four #10 x 3/4" hex head
screws.
NOTE: the top and bottom frame pieces will over-
lap the side frame pieces.
3. HORIZONTAL MASK ONLY - Attach the bottom
frame with four #10 x 3/4" hex head screws.
Attach the bottom brackets with the two screws
at the back of the frame as shown in figure 2.
VERTICAL MASK ONLY - Attach the pull straps to
the bottom slat bar by sliding the looped end of
the pull straps over the ends of the slat bar (See
figure 2 for pull strap attachment). The bottom
roller is spring loaded and has an internal lock to
keep it from retracting during shipping. To disen-
gage the lock pull on the slat bar to unroll the
mask but DO NOT let go of the slat bar. To lock
the roller let the mask retract slowly and the lock
will engage. The lock will only engage when the
frame is laying face down on the floor. When the
frame assembly is hanging on the wall the lock
will not engage. Insert the slat bar into the small
channel on the side frame. Fasten the bottom
frame with four #10 x 3/4" hex head screws.
Attach the bottom brackets with the two screws
at the back of the frame as shown in figure 2.
SLAT BAR
FIG. 1
CHANNEL
1/8" MAX.
PULL STRAP
GUIDE
PULL STRAP
SLAT BAR
VIEWING
SURFACE
FIG. 2
#10 x 3/4" SCREWS
BOTTOM
BRACKET
#10 x 3/4" SCREW


Produktspezifikationen

Marke: Da-Lite
Kategorie: Projektionsfläche
Modell: Pro Imager Vertical Masking System

Brauchst du Hilfe?

Wenn Sie Hilfe mit Da-Lite Pro Imager Vertical Masking System benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Projektionsfläche Da-Lite

Bedienungsanleitung Projektionsfläche

Neueste Bedienungsanleitung für -Kategorien-