Da-Lite Ascender Electrol 84759 Bedienungsanleitung

Da-Lite Nicht kategorisiert Ascender Electrol 84759

Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für Da-Lite Ascender Electrol 84759 (8 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 15 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/8
INSTRUCTION BOOK FOR
Ascender Electrol
2
ATTENTION! Les ressorts des bras de l'écran sont fortement
tendus.
Ne vous placez pas devant l'écran pendant son
fonctionnement.
Ne vous asseyez pas, ne vous tenez pas debout, ou ne placez
aucun objet sur la trappe du caisson de l'écran.
Ne couvrez pas la trappe du caisson de l'écran avec un
revêtement en bois, de la moquette, des stratiiés
supplémentaires, etc. Tout poids ajouté à la trappe du
caisson de l'écran pourrait entraîner, avec le temps, le
dysfonctionnement de l'écran.
La trappe du caisson active un interrupteur de sécurité situé
à l'intérieur du caisson de l'écran. Si vous essayez d'élever
l'écran alors que quelque chose tient la trappe fermée, le
moteur rétractera l'écran. La trappe doit être complètement
fermée pour activer cet interrupteur. Vériiez que la trappe
n'est pas entrouverte.
Pre-Installation
Important Safety Instructions
When using your video equipment, basic safety precautions should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at
least equal to that of the appliance should be used. Cords rated
for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric shock
when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by the
manufacturer may cause a risk of ire, electric shock, or injury to
persons.
Save These Instructions
1. The Ascender screen must be installed on a lat, level surface.
2. Remove the white shipping braces (mounted at the end of the arms to the back of the case).
3. Refer to the chart below for minimum overhead clearance required to raise the screen.
4. Allow 12" clearance from back of screen housing to allow arms to extend properly.
5. Remove packing paper from fabric roller. DO NOT use a knife or sharp object to remove the paper.
Screen Operation
CAUTION!
The arms of the screen are under high spring tension.
Do not stand over the screen while it is operating.
Do not sit, stand, or put anything on the screen case door.
Do not apply anything (wood inish, carpet, additional
laminate, etc.) to the screen case door. Any weight added to
the screen case door may cause the screen to malfunction
over time.
The case door activates a safety switch inside the screen
case. If you attempt to raise the screen while something is
holding the door shut, the motor will reverse and retract the
screen. The door must be fully closed to activate this switch.
Be sure there is nothing holding the door ajar.
Diagonal Extended Height
100" 94"
120" 104"
150" 121"
180" 139"
200" 149"
Diagonal Extended Height
106" 86"
119" 92"
133" 99"
159" 112"
4:3 Video Format 16:9 HDTVFormat
3
CAUTION! Excessive continuous operation may cause
overheating. If this happens, the motor will shut of until it
cools to normal operating temperature. Standard duty cycle
is 1 min. on / 15 min. of.
ATTENTION! Le fonctionnement continu et excessif peut
provoquer une surchaufe et l'arrêt du moteur. Si cela se
produit, les moteurs s'arrêteront jusqu'à qu'ils se soient
refroidis à la température normale de fonctionnement. Le
cycle de fonctionnement normal est de 1 min. en marche / 15
min. à l'arrêt.
Screen Operation (continued)
Ascender Electrol® Installation
1. For installations where the Ascender will be set on the loor, the
box must be secured to loor in at least six places (recommended
hardware is #12 x 2" L wood screws)(Figure 1).
Screw Box Into Floor Stud
Floor
Floor
Box Frame Support
Figure 1 Figure 2
2. For installations where the Ascender will be recessed into the
loor, the box must be secured in at least six places
(recommended hardware is #12 x 2" L wood screws)(Figure2).
1. The Ascender screen can be operated by the included wall
switch or by optional remote controls (IR or RF).
2. To raise the screen, simply push and release the wall switch. The
screen will stop at its preset position. If you push the switch a
second time while it is rising, the screen will stop. By pushing the
switch a third time the screen will retract and close.
3. To lower the screen from the fully up position, press and release
the wall switch and the screen will retract and close.
4. Test the screen by running it up and down a few times. Be
prepared to stop the screen if needed.


Produktspezifikationen

Marke: Da-Lite
Kategorie: Nicht kategorisiert
Modell: Ascender Electrol 84759

Brauchst du Hilfe?

Wenn Sie Hilfe mit Da-Lite Ascender Electrol 84759 benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert Da-Lite

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-