CRUX SWRFD-60E Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für CRUX SWRFD-60E (5 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 12 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/5
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.020620
SWRFD-60E
Radio Replacement with Steering Wheel Control Retention
for Select Ford Vehicles with 4” Screen
1 of 5
RADI O REPLAC EMEN T
SWC R ETENT IO N
+
R
INTERFACING SOLUTIONS
- Retains factory features in select Ford vehicles with 4” screen.
- Pre-programmed to retain factory Steering Wheel Controls.
- Retains factory 4” screen.
- Works on vehicles with or without Sync.
- Retains factory Aux-Input on vehicles without Sync.
- Retains voice command features on vehicles with Sync.
- Phone pick up and hang up functions using the steering wheel control buttons.
PRODUCT FEATURES:
PARTS INCLUDED:
INSTALLATION DIAGRAM:
CAN Module SWC Module SWRFD-60E Harness SWC Cable
AFTERMARKET
RADIO
+12V Constant Yellow
+12V ACC Red
12V Ground Black
Illumination Orange
Reverse Gear Purple/White
Power Antenna Blue/White
Vehicle Speed Sense Pink
Right Front (+) Gray
Right Front (-) Gray/Black
Left Front (+) White
Left Front (-) White/Black
Right Rear (+) Violet
Right Rear (-) Violet/Black
Left Rear (+) Green
Left Rear (-) Green/Black
Factory Aux Input*
24-Pin
Plug
TO FACTORY
RADIO
HARNESS
12-Pin
Connector
SWC
MODULE
ON RAD IO VEHICLE
1 2 3 4 5 6 7 8
AFTERMARKET
RADIO SELECTOR
(See Chart)
FORD
SWC SETTING
(OFF OFF OFF OFF)
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
Cap or insulate if
not being used
Kenwood/JVC (BLUE / YELLOW)
Insulate with tape
if not being used
3.5MM SWC CABLE
Plug in the 3.5MM SWC cable to the 4-pin port
on the module. See “DIP SWITCH SETTINGS” section.
12-Pin
Connector
TO FACTORY
SCREEN
TO FACTORY
SCREEN
HARNESS
SWC 1
with Sync
(Orange wire) SWC 2
without Sync
(Blue wire)
* Retention of factory AUX Input is available ONLY on vehicles WITHOUT Sync.
CAN
MODULE
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.0206202 of 5
RADI O REPLAC EMEN T
SWC R ETENT IO N
+
R
INTERFACING SOLUTIONS
SWRFD-60E
Radio Replacement with Steering Wheel Control Retention
for Select Ford Vehicles with 4” Screen
DIP SWITCH SETTINGS:
FORD STEERING WHEEL CONTROL DIP SWITCH SETTING:
AFTERMARKET RADIO DIP SWITCH SETTINGS:
RADIO BRAND: DIP: 1 2 3 4
Atoto, Dual, Farenheit, Jensen, Pioneer
Power Acoustik, Soundstream
Blaupunkt, Most o-brand Radios
Alpine
Clarion
Kenwood
JVC
Boss, Old Sony
New Sony
OFF OFF ON ON
OFF OFF ON ON
OFF OFF ON ON
OFF OFF OFF OFF
OFF ON ON OFF
OFF ON ON ON
OFF ON OFF ON
OFF ON OFF OFF
OFF OFF ON OFF
SWC MODULE
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
NOTE: For Atoto, Blaupunkt, Dual, Farenheit, Power Acoustik, Soundstream, and most o-brand radios,
check the aftermarket radio’s manual to see if the SWC buttons need to be programmed.
DIP: 5 6 7 8
Ford OFF OFF OFF OFF
SWC MODULE
ON RADIO VEHICLE
1 2 3 4 5 6 7 8
1. The factory AUX Input is retained ONLY on vehicles without Sync system.
2. The Date and Time display MUST BE adjusted prior to removal of the factory radio. You cannot make adjustments once the
radio has been removed.
3. The SWRFD-60E does not retain Sync features.
NOTE: Insulate the Blue/Yellow wire or 3.5mm plug if not being used.
3.5MM SWC CABLE
Plug in the 3.5MM to 4-Pin SWC cable to the SWC module.
NOTES:
IMPORTANT INSTALLATION NOTES:
Plug the 12-pin Molex connector labeled “To CAN Module”
to the CAN module
Plug the 12-pin Molex connector labeled “To SWC Module”
to the smaller SWC Module
Failure to do so will damage the modules!
RED to SWC Key 1
WHITE to SWC Key 2
SHIELD to SWC Ground
For aermarket radios that have wires for SWC connecons, cut o the 3.5mm plug on the Crux SWC Cable and connect the
SWC wires as follows:
Note that there are some radios that only have SWC1 and
SWC2, in this case “shield” does not need to be connected.
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.0206203 of 5
RADI O REPLAC EMEN T
SWC R ETENT IO N
+
R
INTERFACING SOLUTIONS
SWRFD-60E
Radio Replacement with Steering Wheel Control Retention
for Select Ford Vehicles with 4” Screen
IMPORTANT:
Set me and date before removing the factory
radio. Go to Menu > Clock Sengs > Set Time /
Set Date.
1. Carefully remove the top cover of the
screen.
2. Remove the rubber mat on top of
the dashboard.
3. Remove the 2 screws under the
rubber mat.
4. Pop up the top poron of the
dashboard.
5. Remove the 2 screws holding the
radio faceplate.
6. Remove the radio faceplate and
unplug the connector.
INSTALLATION INSTRUCTIONS:
Connect the SWRFD-60E T-harness to the aermarket radio harness. Refer to the diagram on page 1 for wire color
codes.


Produktspezifikationen

Marke: CRUX
Kategorie: Nicht kategorisiert
Modell: SWRFD-60E

Brauchst du Hilfe?

Wenn Sie Hilfe mit CRUX SWRFD-60E benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert CRUX

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung für -Kategorien-