CRUX DKGM-16W Bedienungsanleitung


Lesen Sie kostenlos die đź“– deutsche Bedienungsanleitung fĂĽr CRUX DKGM-16W (7 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war fĂĽr 7 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/7
-Retains factory features in select GM AN 29 Bit vehicles while func oning with an rmarket L
radio.
-Pre-programmed to retain factory Steering Wheel Controls.
-Retains OnStar, factory Rear view camera and chime fun ons.
-Adds Forced Rear view and Front view camera while in mo on using the factory side mirror
controls.
-Supports Bose, non-Bose and Y-91 audio systems.
-
-
EIA color coded wiring for easy installa on.
Includes Double DIN Dash Kit
1. The Front and Rear fading are not retained on Y-91 Bose System.
2. Chime incl es: seat belt, check engine, key in i iud gn on, low fuel, low oil and lights on.
Video Ha ess rn
SETTING THE AFTERMARKET RADIO BRAND
With the key in the o pos o set the DIP switches the corresponding a rmarket radio se ng. n, to
3.5MM SWC CABLE
Plug in the 4-Pin SWC cable to the 4-pin c nector plug on the module. on
NOTE: Cap or insulate the 3.5mm plug, the Blue/Yellow or Green wires if not being used.
SWC 3.5MM PLUG ADAPTER:
R
INTERFACING SOLUTIONS
DKGM-16W
Dash Kit oidaR noitagivaN htiw SKCURT & s’VUS tiB 92 NAL MG rof
PRODUCT FEATURES:
NOTES:
DIP SWITCH SETTINGS:
DKGM-16W Module DKGM-16W HarnessDouble Din Dash Kit
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
1 of 7
Radio Replacement with OnStar Retention, SWC Retention, & Double DIN
SWC Cable &
Antenna Adaptor
rev.03282023
RSE Retention
Harness
Provides Factory Rear Seat Entertainment Activation with RSE Cable #CRUX2444A
-
R
INTERFACING SOLUTIONS
DKGM-16W
Dash Kit oidaR noitagivaN htiw SKCURT & s’VUS tiB 92 NAL MG rof
SELECTING THE AUDIO SYSTEM:
BOSE
Conne on
Non-BOSE
Conne on
2 / 6
If the vehicle is equipped with a Bose system, the DKGM-16W has a built in
DKGM-16W module. The module is also labeled “Bose” and “Non Bose” to
avoid confusion. (see picture below)
If the vehicle is not equipped with a Bose system, plug in the male
module.
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
2 of 7
INSTALLATION DIAGRAM:
Radio Replacement with OnStar Retention, SWC Retention, & Double DIN
rev.03282023
AFTERMARKET
RADIO
Reverse Gear Red/White
Parking Brake Yellow/Black
Illuminaîžźon (+) Orange
+12V Constant Yellow
+12V ACC Red
Ground Black
Right Front (+) Gray
Right Front (-) Gray/Black
Le Front (+) White
Le Front (-) White/Black
Right Rear (+) Violet
Right Rear (-) Violet/Black
Le Rear (+) Green
Le Rear (-) Green/Black
TO FACTORY
HARNESS
24-Pin
Connector
8-Pin
Connector
BOSE NON
BOSE
10-Pin
Connector SWC DIP SWC CAM
1 2 3 4
ON
Video Out
Front Camera
Rear Camera
To OEM Camera
Harness
Gray 20-Pin
Connector VIDEO HARNESS
Chime Volume
Adjustment
1 2 3
ON VR Activation
for OnStar (set DIP#1 to ON)
44-PIN
CONNECTOR
Vehicle Speed Sense
(Green/White)
4-Pin
Connector
Cap or insulate if
not being used
3.5MM SWC CABLE
Plug in the 3.5MM SWC cable to the 4-pin port
on the module. See “DIP SWITCH SETTINGS” section.
LIN BUS (Green/Black)
JVC/Kenwood (Blue / Yellow) Insulate if not
being used
TROUBLESHOOTING
LED
LIGHT LED MODULE FEEDBACK
Solid blue
Flashing blue
Solid red Module providing 12V ACC
CAN not recognized
CAN recognized
12V ACC OFFRed off
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
3 of 7
CHIME VOLUME ADJUSTMENT:
ONSTAR VOLUME ADJUSTMENT:
REAR SEAT ENTERTAINMENT (RSE):
BACK UP CAMERA CONNECTION:
top a sah - W61-MGKD ehT ometer to adjust the chime volume.
I is set at half way by default. To adjust the volume, simply use a t
suitable screw driver and turn the poten ometer clockwise to
increase the volume and counter-clockwise to decrease the volume.
To adjust the OnStar volume, turn on OnStar and adjust the volume using the Steering Wheel Control volume
.level siht eziromem lliw W61-MGKD eht ,tes si ti ecnO .tnemtsujda
The DKGM-16W incl es a video harness that allows a front and rear view camera to be plugged in ud
a viewed on the rmarket radio screen. The vide harness inc des a 20-pin brown connector nd o lu
that plugs into the OEM rear view camera harness to retain the use of the OEM rear view camera (if
equipp The two female video RCAs are used to connect an aed). ermarket front and rear view
came vehicle is not equipped with an OEM rear view cam . ra (if era)
To DKGM-16W
Module (CAM)
Chime
Volume
Adjustment
R
INTERFACING SOLUTIONS
DKGM-16W
Dash Kit oidaR noitagivaN htiw SKCURT & s’VUS tiB 92 NAL MG rof
Radio Replacement with OnStar Retention, SWC Retention, & Double DIN
Video Out
Front Camera
Rear Camera
To OEM Camera
Harness
Gray 20-Pin
Connector
1 2 3 4
ON
SWC DIP SWC CAM
rev.03282023
AV INPUT
TO FACTORY
OVERHEAD
SCREEN
To AV
Input
To AV
Output
To Factory
20-Pin
Connector
AUDIO
MENU
SEEK
SEEK
RADIO
MEDIA
VOLUME
OPEN
CLOSE
1. Remove the OEM radio and plug the CRUX 2444A’s 20 pin connector to the vehicle’s 20 pin factory RSE
connector at the factory radio location. Use one of the Crux parts listed in the Note section.
2. To view videos from the aftermarket radio on the factory overhead screen, connect the RCA’s lebeled
“TO FACTORY OVERHEAD SCREEN” to the aftemarket radio AV output .
3. To retain the use of the factory rear panel AV inputs, plug the RCA’s labeled “AV INPUT” to the aftermarket
radio’s AV input (optional).
4 Test the audio & video on the overhead screen before installing the radio back into the dashboard


Produktspezifikationen

Marke: CRUX
Kategorie: Nicht kategorisiert
Modell: DKGM-16W

Brauchst du Hilfe?

Wenn Sie Hilfe mit CRUX DKGM-16W benötigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert CRUX

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂĽr -Kategorien-