CRUX RVCHN-76D Bedienungsanleitung


Lesen Sie kostenlos die 📖 deutsche Bedienungsanleitung für CRUX RVCHN-76D (2 Seiten) in der Kategorie Nicht kategorisiert. Dieser Bedienungsanleitung war für 5 Personen hilfreich und wurde von 2 Benutzern mit durchschnittlich 4.5 Sternen bewertet

Seite 1/2
RVCHN-76D
Rear View Integration with Lip Mount Camera for
Select Honda Odyssey EX Vehicles with 8” Screen 2011-2013
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.102120
1 of 2
- Automacally switches to rear-view when vehicle is in reverse gear.
- Aermarket lip mount rear view camera included.
- Plug & Play Installaon.
PRODUCT FEATURES:
INSTALLATION DIAGRAM:
Video
Connection
WHITE**
Parking Line
Cut = OFF / Connect = ON
BLUE
(not used
keep connected)
**NOTE: Changes to the parking line option
will take eect after a power cycle.
Camera Power
Regulator
*Camera Ground
(to chassis)
Red wire
Not Used (Insulate)
Make sure the arrows
line up and push in
the connectors well.
8” Factory
Screen
Radio
To factory
screen
To factory
harness
Green Connector at fuse Panel
(Driver’s left kick panel)
Pin 4
Brown/Silver wire
(Reverse Camera Trigger)
Use a length of 18 gauge wire (not included) and
tap the RED camera power wire from the Yellow
RCA to the pin# 4 (BROWN/SILVER) wire on the
Green connector in the fuse panel. This is the
factory reverse trigger wire.
PARTS INCLUDED:
RVCHN-76D Harness CUL-03 Lip Mount Camera
RVCHN-76D
Rear View Integration with Lip Mount Camera for
Select Honda Odyssey EX Vehicles with 8” Screen 2011-2013
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
Crux Interfacing Solutions • Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.102120
2 of 2
VEHICLE APPLICATIONS:
HONDA
2011 - 2013 Odyssey (with 8” screen)
1. Remove the rear ligate panel cover.
2. Drill a 5/8” hole using the hole saw included on the lip under the Honda emblem. Drill the hole at the
as close as you can to the center of the vehicle.
3. Fish the camera cable through 5/8” hole. Do not secure the camera yet unl aer tesng the viewing
angle.
4. Plug the 4 pin barrel connector of the camera cable to the extension cable provided.
5. Route the cable towards the radio locaon.
6. Remove the radio to gain access to the factory screen.
7. Plug the Yellow male RCA of the extension cable to the Yellow female RCA of the RVCHN-76D harness.
8. Unplug the 32 pin connector from behind the screen and plug it to the RVCHN-76D t-harness. Plug the
other end of the t-harness to the screen.
9. To power the camera, you will need to tap the red wire coming out of the Yellow RCA to the BROWN/
SILVER reverse wire found at the fuse panel.
10. Test the camera for funconality before installing. Note that the rear ligate needs to be closed
otherwise the reverse camera will not show on the screen.
INSTALLING THE CAMERA:


Produktspezifikationen

Marke: CRUX
Kategorie: Nicht kategorisiert
Modell: RVCHN-76D

Brauchst du Hilfe?

Wenn Sie Hilfe mit CRUX RVCHN-76D benĂśtigen, stellen Sie unten eine Frage und andere Benutzer werden Ihnen antworten




Bedienungsanleitung Nicht kategorisiert CRUX

Bedienungsanleitung Nicht kategorisiert

Neueste Bedienungsanleitung fĂźr -Kategorien-